PROFILE 3 (SLW & ULTIMATE).pdf - Emenite Limited

Recommendations

Info

2. COMPLEMENTARY ACCE SSORIES2The following drawing, shows our products and accessories to solve the different parts of theroof. For details, please refer to sub chapters 2.1 to 2.7 and to chapter 4 Design Informationfig. 2.12.5Flat wingbarge boardOne piece atwing ridge2.32.1Profile 3roofing sheet2.7Flat wing gusset2.2Two piececorrugatedridge2.2Two piececorrugated ridgeValley piece2.12.4Profile 3roofingsheetOne piece atwing hip ridge2.6Profile 3roofingsheet2.12.1 PROFILE 3® ROOFING SHEETfig. 2.2Profile 3® roofing sheet2.1This roof parts can be solved with ULTIMATE ® and SUPERLIGHTWEIGHT®PROFILE 3 MANUAL11
2.22.2 TWO PIECE CORRUGAT ED RIDGEfg. 2.3Two piece corrugated ridge - InstallationProfile 3Min. 150mmTwo-Piece CorrugatedRidgeMin. 50mmStandard galvanizednail 62.5mm50 x 75mmPurlinThis accessory comes in pairs (upper and lower) which can be articulated to resolve the ridge line of theroof. its main advantage lies in the fact that the two pieces are adjustable and can be installed over anypossible pitch.2.32.3 ONE PIECE FLAT WING RIDGEfig. 2.4One piece flat wing ridge - InstallationOne Piece Flat Wing RidgeMin. 50mmMin. 150mm50 x 75mm PurlinStandard galvanizednail 62.5mmIt is a fixed piece that is intended to resolve the ridge line of roofs with specifc pitches. The available anglesare 15°; 25° and 30°. Th ey can be used over roofs with pitches with the specifed angles ±2°12®PROFILE 3 MANUAL
Page 1 and 2: PROFILE 3TECHNICALMANUAL
Page 3: IndexEmenite ® presentation 4Etex
Page 6 and 7: ®PROFILE 3 MANUAL05
Page 9 and 10: • ULTIMATE ® sheets come in stan
Page 11: Below are the recommended standards
Page 15 and 16: 2.62.6 ONE PIECE FLAT WING HIP RIDG
Page 17 and 18: fig. 3.1Recommended purlin spacings
Page 19 and 20: 3.23.2 FASTENERSFasteners are respo
Page 21 and 22: 44. DESIGN INFORMATION4.14.1 PARTS
Page 23 and 24: advisable to avoid backflow through
Page 25 and 26: These values are valid, only if the
Page 27 and 28: 55. INSTALLATION5.15.1 RECOMMENDED
Page 29 and 30: fig. 5.3Defining the left and the r
Page 31 and 32: 5.75.7 FASTENING PROCEDUREPROFILE 3
Page 33 and 34: 66. ESTIMATION OF MATERIALS6.16.1 E
Page 35 and 36: SOLUTION FOR SUPERLIGHTWEIGHT®NR =
Page 37 and 38: 6.26.2 ESTIMATION OF ACCESSORIESTo
Page 39 and 40: 77. TRANSPORTATIO N HANDLINGAND STO
Page 41 and 42: fig. 7.4Unloading sheets40®PROFILE
Page 43 and 44: 99. CARE AND MAINTENANCEThe followi
Page 45 and 46: oofs when it is wet or windy.• Sh
Page 47: 1111.ENVIRONMENTAL PROTSUSTAINABILI

PROFILE 3 (SLW & ULTIMATE).pdf - Emenite Limited

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?