XP-SK-Series Operation Manual - BJM Pumps

More documents

Recommendations

Info

Lifting:Attach a rope or lifting chain (not included) to the handle (or lifting rings) on the top ofthe pump.Do not lift the pump by the power cable or discharge hose/piping.Proper lifting equipment (rope/chain) must be used.PRE-INSTALLATION INSPECTION1) Check the pump for damage that may have occurred during shipment.2) Inspect the pump for any cracks, dents, damaged threads, etc.3) Check power cord (and Seal Leak Detector cord, if installed) for any cuts ordamage.4) Check for, and tighten any hardware that appears loose.5) Carefully read all tags, decals and markings on the pump.6) Important: Always verify that the pump nameplate amps, voltage, phase, and HPratings match your control panel and power supply.Record the model numbers and serial numbers from the pumps and control panel onthe front of this instruction manual for future reference. Give it to the owner or affix it tothe control panel when finished with the installation.If anything appears to be abnormal, contact your BJM Pumps distributor or BJMPumps, LLC. If damaged, the pump may need to be repaired before use. Do not installor use the pump until appropriate action has been taken.PUMP INSTALLATIONThe Shredder pumps (2 HP) are not designed to pump unscreened solids which couldcontain matter such as bunched paper towels, feminine napkins, tampon applicators,etc. This type of debris can clog the pump & prevent it from operating properly. TheBJM Pumps Shredder Pumps (7 ½ HP and larger) are designed to handle unscreenedsewage.POSITIONING THE PUMPBJM Pumps, XP-SK Series pumps are designed to operate fully or partiallysubmerged. Avoid running the pump dry for extended periods of time. Refer to datasheet for minimum submersion depth for your particular model. Data sheets can beobtained online at www.bjmpumps.com or by calling BJM Pumps, LLC at 860-399-5937.For minimum submergence requirements, refer to EIM ELECTRIC CO., LTD InstructionManual for Installation, Operation and Maintenance for the Explosion Proof SubmersibleMotors (EMQY Series; FM Approved for Class I, Division 1, Group C & D).6
Do not run pump dry.Pump liquid should not exceed a maximum temperature of 104°F.Never place the pump on loose or soft ground. The pump may sink, preventingwater from reaching the impeller. Place on a solid surface or suspend the pumpwith a lifting rope/chain.For maximum pumping capacity, use the proper size non-collapsible hose or rigidpiping. A check valve may be installed after the discharge to prevent back flowwhen the pump is shut off (recommended if static head is 30’ or greater).Take stand off of pump when using slide rail. Keep stand and reattach whentransporting or handling the pump.WIRING INSTRUCTIONSElectrical wiring and protection must be in accordance with the National Electrical Codeper NEC articles 500 through 503 for installation in Class I, Division 1, Group C & DHazardous Locations, and any other applicable state and local electrical requirements.For motor specifications, motor technical data, design features, power supply, electricalwiring, operation, inspecting & maintenance, replacing shaft seals, replacing cables,replacing bearings and other parts, repairing, storing and troubleshooting thesubmersible electric motor, refer to EIM ELECTRIC CO., LTD Instruction Manual forInstallation, Operation and Maintenance for the Explosion Proof Submersible Motors(EMQY Series; FM Approved for Class I, Division 1, Group C & D).Note: All service work on the FM approved motor by EIM Electric Co., needs to be doneby an FM Approved repair facility.The XP-SK Series motors have a separate sensor cable for the motor thermal sensorsand Seal Minder. See Seal Minder - Thermal Motor Sensor Switch section in thismanual for proper connection methodPUMP ROTATIONDO NOT PLACE HANDS IN PUMP SUCTION WHILE CHECKINGMOTOR ROTATION. TO DO SO WILL CAUSE SEVERE PERSONAL INJURY.Before installing a pump, check the pump rotation to insure that wiring has beenconnected properly to power source, and that the green lead of power cord (See wiringdiagram), is connected to a valid ground, momentarily energize the pump, observing thedirections of kick back due to starting torque. Rotation is correct if kick back is in theopposite direction of rotation arrow on the pump casing. If rotation is not correct,switching of any two power leads other than ground will provide the proper rotation.7
Page 3 and 4: TABLE OF CONTENTSINTRODUCTION .....
Page 5: Hazards or unsafe practices that CO
Page 9 and 10: Consult EIM ELELCTRIC Co., LTD. Ins
Page 11 and 12: EXPLODED VIEW OF XP-SK15C (2HP)BJM
Page 13 and 14: EXPLODED VIEW OF XP-SK55C, XP-SK75C
Page 15 and 16: XP-SK SERIES PARTS LISTPump Model X
Page 17 and 18: XP-SK DIMENSIONAL DRAWING17
Page 21 and 22: BJM PUMPS, LLCBJM PUMPS, LLC123 Spe
Page 23 and 24: START-UP REPORT FORMAre guide rails
Page 25 and 26: NOTES:

XP-SK-Series Operation Manual - BJM Pumps

Create successful ePaper yourself

Delete template?

Save as template?