Hotstart Catalog - Davidson Sales Co.

More documents

Recommendations

Info

In-BlockDirect Immersion HeatersNote: In-block heaters are complete with 2-wire w/ground 6foot HPN cord and plug. For cord replacements or “Y”thermocord energy saver, please reference page 56.CUSEngine ModelPart Number120 VoltsPart Number240 Volts Watts Application InformationHeat ShieldRequiredOil HeaterThread Size*Product ImageCaterpillar — <strong>Co</strong>ntinued3406 & 3408except 1998ADEM 2AC-101CATV-151AC-102CATV-15210001500Replaces 1” thread-in plug in the rear ofthe oil cooler bonnet on the right side ofthe engine1” NPT3406E1998 ADEM 2engines onlyTF151-002 TF152-002 1500Replaces the 1” threaded plug thatpoints downward on the top of the rearof the oil cooler bonnetYES1” NPT3406EADEM 3 andADEM2000 enginesAC-101CATV-151AC-102CATV-15210001500Replaces 1” thread-in plug in the rear ofthe oil cooler bonnet on the right side ofthe engine1” NPT3456 15.8LAC-101CATV-151AC-102CATV-15210001500Replaces 1” thread-in plug in the rear ofthe oil cooler bonnet on the right side ofthe engine1” NPTChevrolet/GMC (Small Truck)5.7L V8 (350 CID) FC601-5016.2L V8 Diesel6.5L V8 DieselFC601-PY2NONE 600Mounts in the freeze plug in the engine’sblockNo replacement cord availableCummins6 Cylinder Engines: H, NT, NH, N Family743 CID, 855 CID, 927 CID, “N14”1. Cummins engines are often referred to by their horsepower rating “i.e. 350 Cummins”2. Cummins engines are often referred to as Big Cam, Big Cam2, 3, 4, full flow cooling, etc.All refer to engines of 855 CID Size – listed belowGroup IFlat plate design CUN-151B CUN-152B 15001” NPTFlat plate designwhen the 1/2” NPTopening is used6 bolt flat plate on the right side of theengine. May use either the forward orrear opening depending on clearance.CUN-151BH CUN-152BH 1500 1” NPTGroup IIWhen an external oil cooleris used..Note: When a 4 bolt flat plate element design is encountered, remove the next two bolts on the casting, remove the wholecasting, and replace the casting and element with either CNT-151B/CNT-152B OR CNT151B90/CNT152B90When connectionis 1 1/2” rubberhoseEngines producedAug. 1975 thruJune 1982CNT-151B-90 CNT-152B-90 15006 bolt, flat plate design with an elbowthat will rotate 360 degrees to connectwith any hose or casting1” NPTUses an “O” ringforthe 1 1/4” watertube connectionEngines producedprior to August ‘75CNT-151B CNT-152B 15006 bolt, flat plate design with an elbowthat will rotate 360 degrees to connectwith any hose or casting1” NPT* If supplemental oil heating is desired, this column gives the correct thread size in oil pan. See NOTE on page 54.46 Customer Support: (509) 536-8660 www.hotstart.com
In-BlockDirect Immersion HeatersNote: In-block heaters are complete with 2-wire w/ground 6 footHPN cord and plug. For cord replacements or “Y” thermocordenergy saver, please reference page 56.CUSEngine ModelPart Number120 VoltsPart Number240 Volts Watts Application InformationHeat ShieldRequiredOil HeaterThread Size*Product ImageCummins — <strong>Co</strong>ntinuedGroup IIIFor industrialengines with holepattern reversedCUN-151BREVCUN-152BREV 1500Six bolt flat plate on the right side of theblock1” NPTGroup IV1998 and laterN14 IndustrialPF151-002 PF152-002 1500Six bolt flat plate on the right side of theblock1” NPTAdditional Cummins Engine ModelsCummins A4 cyl & 6 cylCUA-101F CUA-102F 1000Inserts in any of the freeze plugs on rightside of engine. Element points down.ISC/QSC 8.3LISL/QSL 9.0LDD8L-101 DD8L-102 10003/4” NPT threaded plug in theright rear side of engine22mmL10, M11ISMCUL-151 CUL-152 1500Inserts in the forward opening of theheater casting on the right rear of block1” NPTQSB 3.9L, 5.9LISB 5.9TF751-002 TF752-002 7503/4” NPT threaded plug in the frontof the oil cooler casting22mmISM/QSM 11.0LFlat Plate DesignPF151-003 PF152-003 1500 Right rear. Replaces plate. 1” NPTQSX, ISXSignature 600PF151-004 PF152-004 1500Mounts in the oval shaped plate on theright side of the block27mm4BT 3.9LCUB-751FPCUB-101FPCUB-752FPCUB-102FP7501000Inserts in any of the freeze plugsright side of engineCheck ExhaustRouting22mm6BT 5.9LCUB-751FPCUB-101FPCUB-151FPCUB-752FPCUB-102FPCUB-152FP75010001500Inserts in any of the freeze plugsright side of engineCheck ExhaustRouting22mm6CT 8.3L CUC-151FP CUC-152FP 1500Inserts in the freeze plugright rear of the blockDetroit Diesel22mmSERIES 104 cylinderPhaser enginesPER-751FPPER-101FPPER-752FPPER-102FP7501000Mounts in the 1-1/4” freeze plugopening on either side of the engineSERIES 106 cylinderPhaser enginesPER-151FP PER-152FP 1500Mounts in the 1-1/2” freeze plug on theright side of the engineSERIES 30 DD8L-101 DD8L-102 1000Mounts in the 3/4” NPT opening in theblock* If supplemental oil heating is desired, this column gives the correct thread size in oil pan. See NOTE on page 54.Customer Support: (509) 536-8660www.hotstart.com47
Page 1 and 2: P R O D U C T S C A T A L O GIMC-70
Page 3 and 4: P R O D U C T C A T A L O GSECTION
Page 5: EngineDisplacementModel Number Volt
Page 8 and 9: Industrial TankHeatersEngineDisplac
Page 12 and 13: Dimensional Drawingsinch, millimete
Page 18 and 19: Dimensional Drawingsinch, millimete
Page 20 and 21: Installation Instructions for Tank-
Page 22 and 23: HOTflowHeatersCSM SeriesSingle & Th
Page 24 and 25: HOTflowHeatersEngineDisplacement120
Page 26 and 27: Oil HeatersOilCapacityWeathertightH
Page 28 and 29: IndustrialImmersion Heaters2” Scr
Page 30 and 31: V-ClampImmersion HeatersThreadless
Page 32 and 33: 5 SECTIONP R O D U C T C A T A L O
Page 34 and 35: Temperature ControlsNOTE: When usin
Page 36 and 37: Control SystemsCONTROL SYSTEMSCONTR
Page 38 and 39: 38 Customer Support: (509) 536-8660
Page 40 and 41: Battery Heating PadsBattery heater
Page 42 and 43: SiliconePad HeatersModel Number Dim
Page 44 and 45: In-BlockDirect Immersion HeatersNot
Page 54 and 55: ReplacementCords &ThermostatsCordLe
Page 56 and 57: Specifying anEngine Heater1. Determ
Page 58: Customer ServicesTo better serve yo

Hotstart Catalog - Davidson Sales Co.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?