Instruction Manual Model XTpc Pipe & Cable ... - EngineerSupply

More documents

Recommendations

Info

Receiver ConnectorSECTION V: CONNECTORS AND ACCESSORIESThis 2.5mm phone plug accepts any mono or stereo earphones or headphones. The receiver automaticallydetects the insertion of the plug and routes the audio signals to the earphones or headphones, silencing theinternal speaker.Transmitter ConnectorThis circular, lock-type, 8-pin connector is used to connect the conductive clips, the optional inductiveclamp, optional inductive antenna, or the battery charger to the transmitter. The transmitter automaticallydetects what accessory has been plugged in and adjusts its operation and indicators accordingly. It isrecommended that you turn the transmitter's power OFF before removing or inserting accessories from/intothe connector.Standard AccessoriesA - Inductive Signal OutB - N/CC - Signal GNDD - Conductive / Clamp Signal OutE - Battery Charger +VF - Battery Temperature SensorG - Battery Charger GNDH - Accessory ID ResistorThe following accessories are included with all XTpc models: Hard carrying case Instruction manual Belt receiver holder cup Locating 101 Book Ground stake Locating DVD Conductive clips Universal power supply for battery charger w/ Disposable Battery for Receivercountry-specific power cord Battery charger for Transmitter Battery Vehicle power supply for battery chargerFor the XT512 model, the following accessories are included: Soft carrying bag Instruction manual Belt receiver holder cup Locating 101 Book Disposable Battery Locating DVDOptional AccessoriesMany optional accessories are available for the XTpc Pipe and Cable locator line. The following listincludes the most common ones, please contact Schonstedt for details and additional optional accessoriesnot listed below. Inductive antenna (33 kHz or 82 kHz) Inductive clamp (3-1/8" ID, 5" ID and 7" ID) Sondes (33 kHz, 82 kHz and 512 Hz) "Carry All " duffel bag Padded transmitter and accessory belt-pouch w/belt Shoulder strap Medium size conductive clips Large size conductive clips- 14 -
SECTION VI: BATTERIES AND CHARGERReceiver BatteryThe XTpc receiver is powered by one 9-volt disposable battery. The battery is located in the handle of theinstrument and can be accessed by turning the screw counterclockwise by hand or with the use of ascrewdriver or coin. To remove the battery, simply tilt the unit so that the handle is pointing down, and thebattery will slide out. When replacing the battery, look at the inside of the battery door for the properbattery orientation. (The positive terminal should be on the right on the inside of the unit) As a safetymeasure the unit has been "keyed" so that the battery will only make contact when it is inserted in thecorrect orientation. For this reason you should never have to force the battery door closed. If the batterydoes not seem to be going in all the way, remove the battery, reverse its orientation and then replace it.Transmitter BatteryThe batteries for the transmitter are 6 rechargeable NiMH cells packed to provide 7.2- volt, and need not bereplaced. It is recommended to first charge the batteries for at least 4 hours before the initial use. If yoususpect that the batteries are malfunctioning please contact Schonstedt Instrument Company.Transmitter Battery ChargerThe battery charger is especially designed to charge the internal NiMH, 7.2-volt battery pack that powersthe transmitter. It will typically charge a fully discharged battery in under 4 hrs and it has smart safetyfeatures to monitor the charge process.The color LED indicators work as follows:TRANSMITTERBATTERY STATUSREADY LIGHT(Green)CHARGING LIGHT(Yellow)Fully Charged ON OFFCharging OFF ON or FlashingThe charger can be powered by the included AC power supply or the included vehicle power supply. TheAC power supply operates from a range of input voltages and frequencies to suit most countries. Thevehicle power supply allows the battery to be recharged while driving from job to job. Its input voltage is12 to 14.4 VDC from a car battery.- 15 -
Page 1 and 2: Instruction ManualModel XTpcPipe &
Page 3 and 4: Important NoticeSchonstedt believes
Page 5: the signal being traced by the rece
Page 8 and 9: locate, it just means that there is
Page 10 and 11: TransmitterON/OFF - This is a momen
Page 12 and 13: When all three elements of this ind
Page 16 and 17: Recommendations for Battery Chargin
Page 18 and 19: SECTION VIII : OPERATING RECOMMENDA

Instruction Manual Model XTpc Pipe & Cable ... - EngineerSupply

Create successful ePaper yourself

Delete template?

Save as template?