t230 grass trimmer t230x grass trimmer c230 ... - Shindaiwa USA

More documents

Recommendations

Info

Starting the EngineIMPORTANT!Engine ignition is controlled by a twoposition switch mounted on the throttlehousing labeled, “I” for ON or START and“O” for OFF or STOP.Make sure thecutting attachmentis clear ofobstructions!IMPORTANT!If the engine fails to start after several attemptswith the choke in the closed position,the engine may be flooded with fuel.If flooding is suspected, move the chokelever to the open position and repeatedlypull the recoil starter to remove excessfuel and start the engine. If the engine stillfails to start, refer to the troubleshootingsection of this manual.Figure 22230321. Slide the ignition switch to the “I” position(engine ON).ReturnTubeFigure 254. While holding the outer tube firmly withone hand, slowly pull the recoil starterhandle until resistance is felt, then pullquickly to start the engine.CAUTION!Do not pull the recoil starter to the endof the rope travel. Pulling the recoilstarter to the end of the rope travel candamage the starter.When the Engine Starts... After the engine starts, allow the engineto warm up at idle 2 or 3 minutes beforeoperating the unit. After the engine is warm, pickup the unit and clip on the harness if soequipped. See page 13. Advancing the throttle makes the cuttingattachment turn faster; releasingthe throttle permits the attachment tostop turning. If the cutting attachmentcontinues to rotate when the enginereturns to idle, carburetor idle speedshould be adjusted (page 13).Primer BulbFigure 232. Press the primer bulb until fuel can beseen flowing in the transparent returntube.IMPORTANT!The primer system only pushes fuelthrough the carburetor. Repeatedlypressing the primer bulb will not flood theengine with fuel.WARNING!The cutting attachment may rotatewhen the engine is started!5. When the engine starts, slowly move thechoke lever to the “OPEN” position. SeeFigure 26. (If the engine stops after theinitial start, close the choke and restart.)OpenStopping the EngineFigure 2723037Idle the engine briefly before stopping(about 2 minutes), then slide the ignitionswitch to the “O” (Engine OFF) position.ClosedFigure 2623036Figure 24230343. (Cold Engine Only) Set the chokelever to the CLOSED position.WARNING!Never start the engine from the operatingposition.12
Adjusting Engine IdleIdle AdjustingScrewFigure 28The engine must return to idle speedwhenever the throttle lever is released.Idle speed is adjustable, and must be setlow enough to permit the engine clutch todisengage the cutting attachment.Idle Speed AdjustmentWARNING!The cutting attachment must NEVERrotate at engine idle! If the idle speedcannot be adjusted by the proceduredescribed here, return the unit to yourShindaiwa dealer for inspection.1. Place the unit on the ground, then startthe engine, and then allow it to idle 2-3minutes until warm.2. If the attachment rotates when theengine is at idle, reduce the idle speedby turning the idle adjustment screwcounter-clockwise. See Figure 26.3. If a tachometer is available, the engine idlespeed should be final adjusted to 2,750(±250) RPM (min -1 ).4. Carburetor fuel mixture adjustments arepreset at factory on units with emissioncontrol systems and cannot be servicedin the field.Checking Unit ConditionNEVER operate the unit with the cuttingattachment shield or other protectivedevices (harness, ignition switch, bladeretention clip, etc.) removed!WARNING!A cutting attachment shield or otherprotective device is no guarantee ofprotection against ricochet. YOU MUSTALWAYS GUARD AGAINST FLYINGDEBRIS!Use only authorized Shindaiwa parts andaccessories with your Shindaiwa trimmer,brushcutter, or lawn edger. Do not makemodifications to this unit without the writtenapproval of Shindaiwa, Inc.ALWAYS make sure the cutting attachmentis properly installed and firmly tightenedbefore operation.NEVER use a cracked or warped cuttingattachment: If a properly installed attachmentvibrates, replace the attachment withnew one andre-check.ALWAYS stop the engine immediately andcheck for damage if you strike a foreignobject or if the unit becomes tangled. Donot operate with broken or damaged equipment.NEVER allow the engine to run at highRPM without a load. Doing so could damagethe engine.NEVER operate a unit with worn or damagedfasteners or attachment holders.NEVER cut with a dull blade. Doing so willincrease the risk of blade thrust and mayalso cause equipment damage.Shoulder StrapAdjust the shoulder strap so the shoulder padrests comfortably on the off-side shoulder andthe cutting path of the cutting attachmentis parallel to the ground. Make sure allhooks and adjustment devices are secure.Optional AccessoriesShoulder Strap...................P/N 22410-17202Hanger................................P/N 22410-12210Hanger Bolt........................P/N 01020-05120Hanger Nut.........................P/N 01500-05041Grass TrimmingNOTE:Although a shoulder strap accessory is notrequired for use with a grass trimmer, ashoulder strap can increase operator comfortduring extended periods of operation. SeeFigure 29.Figure 29Using a BladeWARNING!Always wear a shoulder strap when operatingthis unit with a blade. A shoulderstrap is also recommended whenusing trimmer line.Shoulder straprequired for usewithbrushcuttersFigure 30NOTE:Using a shoulder strap with a brush-cutterallows you to maintain proper control of theunit and reduces fatigue during extendedoperation.13
Page 1 and 2: ENGLISHSHINDAIWA OWNER’S/OPERATOR
Page 3 and 4: General Safety InstructionsStay Ale
Page 5 and 6: Unit DescriptionUsing the accompany
Page 7 and 8: AssemblyHandlebar C230Ignition Swit
Page 9 and 10: AssemblyCutting Attachment Shield A
Page 11: AssemblyBlade C230/T230X (continued
Page 15 and 16: Using A Brushcutter Blade C230/T230
Page 17 and 18: 10/15-Hour MaintenanceFigure 360.02
Page 19 and 20: Long Term StorageWhenever the unit
Page 21 and 22: Troubleshooting Guide (continued)AD
Page 23 and 24: NOTES23

t230 grass trimmer t230x grass trimmer c230 ... - Shindaiwa USA

Create successful ePaper yourself

Delete template?

Save as template?