PXA30-K11 Extension module for KNX / EIB - Siemens

9 280
DESIGO PX
Extension module
for KNX / EIB
for KNX / EIB integration
PXA30-K11
• Integration of KNX / EIB subsystems at the automation level of the DESIGO
building automation and control system
• Plugs into the modular automation station type PXC...-U
Functions
• Integration of max. 45 RXB… room controllers (S-mode or polling)
• Integration of max. 2000 data points from KNX / EIB 3rd party systems (S-mode)
Types
PXA30-K11
Extension module
Compatibility
The module is plugged into a PXC64-U or PXC128-U automation station.
CM1N9280en_02
18 May 2009 Building Technologies

Ordering
When ordering, please specify the quantity, product name and type code.
Example:
30 Extension modules PXA30-K11
Design
• Two-part snap-together housing (plastic)
• Cover for contact protection
• PCB with electronic components
• Two-pole EIB/KNX connection terminals
• RJ45 service socket
• Service pin
9280Z01
Mounting
The extension module is plugged into the PXC..-U modular automation station.
It is important to follow the instructions supplied with the device, in particular:
• Avoid touching the connector pins (ESD precautions)
• Push the module firmly into position (1.5 mm) and check that it is securely in place
so that the fine contact pins interlock properly.
2
1
3
3
1 Plug-in unit
2 Device base
3 Extension module
9280Z02
2/4
Siemens PXA30-K11 – Extension module for KNX / EIB CM1N9280en_02
Building Technologies 18 May 2009

Commissioning
For integration operation the corresponding firmware must be loaded into the PXC...-U
automation station.
Disposal
The device includes electrical and electronic components and must not be disposed of
as domestic waste.
Current local legislation must be observed.
Technical data
Elements of the user interface Service pin
Programming mode
KNX / EIB interface
Stranded or solid conductors,
2 x 1.0 mm 2
KNX / EIB bus Interface type KNX / EIB (electrically isolated)
Transceiver
TP-UART
Bus current
5 mA
Baud rate
9.6 kbit/s
Bus topology, bus termination
Refer to KNX / EIB manual
Service interface
RJ45
Housing
Protection standard to EN 60529 IP 30
protection standard
Protection class Insulation protection class II
Ambient conditions Normal operation Class 3K5 to IEC 721
Temperature 0 ... 50 °C
Humidity
< 85 % rh
Transport Class 2K3 to IEC 721
Temperature – 25 ... 65 °C
Humidity
< 95 % rh
Industry standards
Product safety
Automatic electronic controls for
household and similar use EN 60730-1
Special requirements for energy controllers EN 60730-2-11
Electromagnetic compatibility
Interference immunity
EN 61000-6-2 (Industry)
Emitted interference
EN 61000-6-3 (Residential)
Meets the requirements for CE marking:
EMC Directive
2004/108/EG
Dimensions
See “Dimensions”
Weight Excluding packaging 75 g
With packaging
95 g
Siemens PXA30-K11 – Extension module for KNX / EIB CM1N9280en_02
Building Technologies 18 May 2009
3/4

Connections
Standard RJ45 socket
for service
87654321
9280Z03
1 KNX data cable (CE+)
2 KNX data cable (CE–)
3 Not used
4 Not used
5 Not used
6 Not used
7 Not used
8 Not used
KNX / EIB-interface
9280Z05
+ KNX data cable (CE+)
– KNX data cable (CE–)
Dimensions
Dimensions in mm
9280M01
111
62 33
28
4/4
© 2004 – 2009 Siemens Switzerland Ltd. Subject to alteration
Siemens PXA30-K11 – Extension module for KNX / EIB CM1N9280en_02
Building Technologies 18 May 2009