Understanding APIICP653 Reading 2-650-Selected Reading

More documents

Recommendations

Info

API 653 Exam Administration -- Publications Effectivity Sheet FOR: November 2015, March 2016 and July 2016 Listed below are the effective editions of the publications required for this exam for the date(s) shown above. API Recommended Practice 571, Damage Mechanisms Affecting Fixed Equipment in the Refining Industry, Second Edition, April 2011 Charlie Chong/ Fion Zhang
ATTENTION: Only the following sections / mechanisms from RP 571 are included on the exam: Section 3, Definitions Par. 4.2.7 Brittle Fracture 4.2.16 Mechanical Fatigue 4.3.2 Atmospheric Corrosion 4.3.3 Corrosion Under insulation (CUI) 4.3.8 Microbiologically Induced Corrosion (MIC) 4.3.9 Soil Corrosion 4.3.10 Caustic Corrosion 4.5.1 Chloride Stress Corrosion Cracking (Cl-SCC) 4.5.3 Caustic Stress Corrosion Cracking (Caustic Embrittlement) 5.1.1.10 Sour Water Corrosion (Acidic) 5.1.1.11 Sulfuric Acid Corrosion Charlie Chong/ Fion Zhang
Page 1 and 2: Understanding APIICP653 Reading 2 A
Page 3 and 4: Petroleum Tank Charlie Chong/ Fion
Page 5: API 653 Exam Administration -- Publ
Page 9 and 10: • American Society of Mechanical
Page 11 and 12: Charlie Chong/ Fion Zhang
Page 15 and 16: API650-2013 BOK Search Keyword “6
Page 17 and 18: I. CALCULATIONS & TABULAR EVALUATIO
Page 19 and 20: 4. WELD SIZES FOR SHELL & ROOF OPEN
Page 21 and 22: 10. RECONSTRUCTED TANK SHELL - MINI
Page 23 and 24: A. The inspector should have the kn
Page 25 and 26: III. NONDESTRUCTIVE EXAMINATION ASM
Page 27 and 28: 10. API 650, Annex D 11. API 650, A
Page 29 and 30: API Standard 653, Tank Inspection,
Page 31 and 32: A. Calculation questions will be or
Page 33 and 34: 8.1.1 Application Radiographic exam
Page 35 and 36: Figure 8.1—Radiographic Requireme
Page 37 and 38: Figure 8.1—Radiographic Requireme
Page 39 and 40: 6. Complete radiograph of each vert
Page 41 and 42: c) Vertical joints in which the she
Page 43 and 44: 8.1.2.3 One spot radiograph shall b
Page 45 and 46: 8.1.2.9 When bottom annular plates
Page 47 and 48: 8.1.3.3 The requirements of T-285 i
Page 49 and 50: 8.1.6 Determination of Limits of De
Page 51 and 52: 8.1.7 Repair of Defective Welds 8.1
Page 55 and 56: 4. WELD SIZES FOR SHELL & ROOF OPEN
Page 57 and 58:
C L Nozzle Neck bevel should be abo
Page 59 and 60:
C L Regular Low type t A (see Note
Page 61 and 62:
Shell plate of lowest shell course
Page 63 and 64:
16-mm ( 5 /8-in.) diameter bolts in
Page 65 and 66:
5 mm ( 3 /16 in.) 6 mm ( 1 /4 in.)
Page 67 and 68:
Table 5.6a—Dimensions for Shell N
Page 69 and 70:
Column 1 Column 2 Column 3 Column 4
Page 71 and 72:
8. IMPACT TESTING The inspector sho
Page 73 and 74:
4.2.9.3 An impact test shall be per
Page 75 and 76:
NOTE 1 The Group II and Group V lin
Page 77 and 78:
Table 4.3a—Linear Equations for F
Page 79 and 80:
Charlie Chong/ Fion Zhang
Page 81 and 82:
10. RECONSTRUCTED TANK SHELL - MINI
Page 83 and 84:
5.6.3.2 The required minimum thickn
Page 85 and 86:
A. The inspector should have the kn
Page 87 and 88:
9.2.1.2 The welding procedures used
Page 89 and 90:
9.2.2 Impact Tests 9.2.2.1 Impact t
Page 91 and 92:
9.2.2.5 Impact tests shall show min
Page 93 and 94:
C. API-650 and API-653: General wel
Page 95 and 96:
API Standard 653, Tank Inspection,
Page 97 and 98:
BODY OF KNOWLEDGE API-653 ABOVEGROU
Page 99 and 100:
Determining joint efficiency may be
Page 101 and 102:
Calculate “MRT”, minimum remain
Page 103 and 104:
III. NONDESTRUCTIVE EXAMINATION ASM
Page 105 and 106:
7. NDE requirements for eddy curren
Page 107 and 108:
a) types of tanks covered b) applic
Page 109 and 110:
API-653 ABOVEGROUND STORAGE TANK Pu
Page 111 and 112:
http://independent.academia.edu/Cha
Page 113 and 114:
Charlie Chong/ Fion Zhang
Page 115:
Good Luck! Charlie Chong/ Fion Zhan
show all

Understanding APIICP653 Reading 2-650-Selected Reading

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?