Understanding APIICP653 Reading 2-650-Selected Reading

More documents

Recommendations

Info

• API Recommended Practice 575, Inspection of Atmospheric and Low- Pressure Storage Tanks, Third Edition, April 2014 • API Recommended Practice 577 – Welding Inspection and Metallurgy, Second Edition, December 2013 • API Standard <strong>650</strong>, Welded Tanks for Oil Storage, Twelfth Edition, March 2013 with Addendum 1 (September 2014), Errata 1 (July 2013), and Errata 2 (December 2014). • API Recommended Practice 651, Cathodic Protection of Aboveground Petroleum Storage Tanks, Fourth Edition, September 2014. • API Recommended Practice 652, Lining of Aboveground Petroleum Storage Tank Bottoms, Fourth Edition, September 2014 • API Standard 653, Tank Inspection, Repair, Alteration, and Reconstruction, Fifth Edition, November 2014. Charlie Chong/ Fion Zhang
• American Society of Mechanical Engineers (ASME), Boiler and Pressure Vessel Code, 2013 Edition i. ASME Section V, Nondestructive Examination, Articles 1, 2, 6, 7 and 23 (section SE-797 only) ii. Section IX, Welding and Brazing Qualifications (Welding Only) See end of this study note for API Official BOK Charlie Chong/ Fion Zhang
Page 1 and 2: Understanding APIICP653 Reading 2 A
Page 3 and 4: Petroleum Tank Charlie Chong/ Fion
Page 5 and 6: API 653 Exam Administration -- Publ
Page 7: ATTENTION: Only the following secti
Page 11 and 12: Charlie Chong/ Fion Zhang
Page 15 and 16: API650-2013 BOK Search Keyword “6
Page 17 and 18: I. CALCULATIONS & TABULAR EVALUATIO
Page 19 and 20: 4. WELD SIZES FOR SHELL & ROOF OPEN
Page 21 and 22: 10. RECONSTRUCTED TANK SHELL - MINI
Page 23 and 24: A. The inspector should have the kn
Page 25 and 26: III. NONDESTRUCTIVE EXAMINATION ASM
Page 27 and 28: 10. API 650, Annex D 11. API 650, A
Page 29 and 30: API Standard 653, Tank Inspection,
Page 31 and 32: A. Calculation questions will be or
Page 33 and 34: 8.1.1 Application Radiographic exam
Page 35 and 36: Figure 8.1—Radiographic Requireme
Page 37 and 38: Figure 8.1—Radiographic Requireme
Page 39 and 40: 6. Complete radiograph of each vert
Page 41 and 42: c) Vertical joints in which the she
Page 43 and 44: 8.1.2.3 One spot radiograph shall b
Page 45 and 46: 8.1.2.9 When bottom annular plates
Page 47 and 48: 8.1.3.3 The requirements of T-285 i
Page 49 and 50: 8.1.6 Determination of Limits of De
Page 51 and 52: 8.1.7 Repair of Defective Welds 8.1
Page 55 and 56: 4. WELD SIZES FOR SHELL & ROOF OPEN
Page 57 and 58: C L Nozzle Neck bevel should be abo
Page 59 and 60:
C L Regular Low type t A (see Note
Page 61 and 62:
Shell plate of lowest shell course
Page 63 and 64:
16-mm ( 5 /8-in.) diameter bolts in
Page 65 and 66:
5 mm ( 3 /16 in.) 6 mm ( 1 /4 in.)
Page 67 and 68:
Table 5.6a—Dimensions for Shell N
Page 69 and 70:
Column 1 Column 2 Column 3 Column 4
Page 71 and 72:
8. IMPACT TESTING The inspector sho
Page 73 and 74:
4.2.9.3 An impact test shall be per
Page 75 and 76:
NOTE 1 The Group II and Group V lin
Page 77 and 78:
Table 4.3a—Linear Equations for F
Page 79 and 80:
Charlie Chong/ Fion Zhang
Page 81 and 82:
10. RECONSTRUCTED TANK SHELL - MINI
Page 83 and 84:
5.6.3.2 The required minimum thickn
Page 85 and 86:
A. The inspector should have the kn
Page 87 and 88:
9.2.1.2 The welding procedures used
Page 89 and 90:
9.2.2 Impact Tests 9.2.2.1 Impact t
Page 91 and 92:
9.2.2.5 Impact tests shall show min
Page 93 and 94:
C. API-650 and API-653: General wel
Page 95 and 96:
API Standard 653, Tank Inspection,
Page 97 and 98:
BODY OF KNOWLEDGE API-653 ABOVEGROU
Page 99 and 100:
Determining joint efficiency may be
Page 101 and 102:
Calculate “MRT”, minimum remain
Page 103 and 104:
III. NONDESTRUCTIVE EXAMINATION ASM
Page 105 and 106:
7. NDE requirements for eddy curren
Page 107 and 108:
a) types of tanks covered b) applic
Page 109 and 110:
API-653 ABOVEGROUND STORAGE TANK Pu
Page 111 and 112:
http://independent.academia.edu/Cha
Page 113 and 114:
Charlie Chong/ Fion Zhang
Page 115:
Good Luck! Charlie Chong/ Fion Zhan
show all

Understanding APIICP653 Reading 2-650-Selected Reading

Create successful ePaper yourself

Delete template?

Save as template?