Understanding API ICP653 Reading 14-Worksheet-10A

More documents

Recommendations

Info

Annex J (normative) Shop-Assembled Storage Tanks Table J.1b—Minimum Roof Depths for Shop-Assembled Dome-Roof Tanks (USC) Charlie Chong/ Fion Zhang
Q81. For impact testing weld metal over 1½” inches how much shall the impact value be raised for each ½” inch of material? (a) 2 foot-pounds (b) 3 foot-pounds (c) 5 foot-pounds (d) 6foot-pounds REF: 650 7.2.2.5 or Table 2-4 ANS: (c) Charlie Chong/ Fion Zhang
Page 1 and 2: Charlie Chong/ Fion Zhang
Page 3 and 4: AST Tanks Charlie Chong/ Fion Zhang
Page 5 and 6: Adobe Acrobat Reader Hotkeys Ctrl +
Page 9 and 10: API 653 Exam Administration -- Publ
Page 11 and 12: ATTENTION: Only the following secti
Page 13 and 14: • American Society of Mechanical
Page 15 and 16: http://independent.academia.edu/Cha
Page 17 and 18: The Magical Book of Tank Inspection
Page 19 and 20: 闭门练功 Charlie Chong/ Fion
Page 23: Q78. For dome roofs that are flange
Page 27 and 28: 9.2.2.5 Impact tests shall show min
Page 29 and 30: Q105. In performance qualification
Page 31 and 32: GENERAL NOTE: The “Thickness of W
Page 33 and 34: 9.2.1.3 Material specifications lis
Page 35 and 36: Q129. On an initial in-service rive
Page 37 and 38: Q137. Plate for shells, roofs and b
Page 39 and 40: Q160. The "L" in actual thickness d
Page 43 and 44: Q259. What percentage of selected s
Page 45 and 46: Q61. Per API 650, external floating
Page 47 and 48: Q71. The maximum reinforcement thic
Page 49 and 50: API650: 7.2.3 Shells 7.2.3.1 Plates
Page 51 and 52: API575: Annex A (normative) Selecte
Page 53 and 54: Q119. You are adding a 6 inch blend
Page 55 and 56: Q120. Who is responsible for compli
Page 57 and 58: Happy Holi Charlie Chong/ Fion Zhan
Page 59 and 60: QW-304 Welders Except for the speci
Page 61 and 62: QW-306 Combination of Welding Proce
Page 65 and 66: QW-401.3 Supplementary Essential Va
Page 67 and 68: Q7. The test coupon for a PQR consi
Page 69 and 70: Q9. What production base metals is
Page 71 and 72: Q1 . When qualifying a welder at 6G
Page 73 and 74: Q31. Welding electrodes are grouped
Page 75 and 76:
Q93. For P-11 materials, weld groov
Page 77 and 78:
Q12. What is the minimum dimension
Page 79 and 80:
Charlie Chong/ Fion Zhang
Page 81 and 82:
Q17. What are the required spacings
Page 83 and 84:
Q 26. Determine the minimum accepta
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
NOTE 1 Dimensions given are from to
Page 91 and 92:
d. A welded-on patch plate may be p
Page 93 and 94:
9.10.1.2 Repairs within the Critica
Page 95 and 96:
Things to remember on critical zone
Page 97 and 98:
4.4.3 Tank Bottom Release Preventio
Page 99 and 100:
Q57. What finished welds do NOT req
Page 101 and 102:
Q70. Where exterior tank bottom cor
Page 103 and 104:
Q77. The standard used for repairs
Page 105 and 106:
Q88. In order to qualify for a hydr
Page 107 and 108:
Q89. In order to qualify for a hydr
Page 109 and 110:
Q9) A hot tap in a 1.25" thick tank
Page 111 and 112:
9.14.1.2 The minimum height of tank
Page 113 and 114:
Q34. Corrosion on the underside of
Page 115 and 116:
Q42. Radiographs for an evaluated,
Page 117 and 118:
Q54. What type of tank settlement d
Page 119 and 120:
Figure 9.1—Acceptable Details for
Page 121 and 122:
Clay Pot Rice 煲仔饭 Charlie C
Page 123 and 124:
Q56. Guidance for evaluation of an
Page 125 and 126:
Good Luck! Charlie Chong/ Fion Zhan
show all

Understanding API ICP653 Reading 14-Worksheet-10A

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?