- Page 1 and 2: Hydraulic Services Design Guide 5th
- Page 3 and 4: 1 Chapter One Chapter 1 - Introduct
- Page 5 and 6: Within the Copper Alliance, ICA mai
- Page 7 and 8: 2 Chapter Two Chapter 2 - The Histo
- Page 9 and 10: Copper Ores An ore is a rock (Figur
- Page 11 and 12: Recycling Another important source
- Page 13 and 14: 3 Chapter Three Chapter 3 - Copper
- Page 15 and 16: Melting The charge of raw materials
- Page 17 and 18: Extrusion Extrusion is often quite
- Page 19 and 20: Copper plumbing tube is sold in eit
- Page 21 and 22: 4 Chapter Four Chapter 4 - Copper T
- Page 23 and 24: Copper: 99.90% minimum Phosphorus:
- Page 25 and 26: Nominal Size DN AS 1432 TYPE C Actu
- Page 27 and 28: Copper Tube - Safe Working Pressure
- Page 29 and 30: Figure 4.2 Examples of acceptable m
- Page 31 and 32: Sanitary Piping Sanitary piping sha
- Page 33 and 34: 5 Chapter Five Chapter 5 - Water Su
- Page 35 and 36: Water Conservation We all recognise
- Page 37 and 38: Desalination / Blended Water Supply
- Page 39 and 40: The following information forms par
- Page 41: Rainwater Rainwater collection is t
- Page 45 and 46: There are many case studies where M
- Page 47 and 48: Pitting corrosion Pitting (non-unif
- Page 49 and 50: Interface Corrosion Corrosion can b
- Page 51 and 52: Stray current corrosion Where DC. e
- Page 53 and 54: 7 Chapter Seven Chapter 7 - Joining
- Page 55 and 56: Figure 7.1a Assembling Copper Flare
- Page 57 and 58: PressFit Seals Different PressFit f
- Page 59 and 60: DN50 Class/Table DN65 DN80 DN100 DN
- Page 61 and 62: 8 Chapter Eight Chapter 8 - Pipewor
- Page 63 and 64: 0 C Copper Rates of Thermal Expansi
- Page 65 and 66: Height of Expansion Loop As a guide
- Page 67 and 68: Expansion Allowance at Tees Figure
- Page 69 and 70: 9 Chapter Nine Chapter 9 - Pipe Sup
- Page 71 and 72: Anchors Pipe anchors prevent axial
- Page 73 and 74: Figure 9.4 Standard Saddle Clamp Fi
- Page 75 and 76: Piping Support Design AS/NZS 3500 W
- Page 77 and 78: Cantilever Brackets Cantilever brac
- Page 79 and 80: 10 Chapter Ten Chapter 10 - Valves
- Page 81 and 82: Gate valves are primarily used as i
- Page 83 and 84: Ball Valves - Screwed and Compressi
- Page 85 and 86: Temperature & Pressure Relief Valve
- Page 87 and 88: Combination Isolating, Line Straine
- Page 89 and 90: Figure 10.16a Butterfly Valve Figur
- Page 91 and 92: Balancing Valves Highly quality STA
- Page 93 and 94:
Swing Check Valves A swing check va
- Page 95 and 96:
11 Chapter Eleven Chapter 11 - Desi
- Page 97 and 98:
Design Principles Water quality The
- Page 99 and 100:
Water Demand for Building Water dem
- Page 101 and 102:
Definition of Water Pressures Stati
- Page 103 and 104:
Pipework Protection Wherever possib
- Page 105 and 106:
12 Chapter Twelve Chapter 12 - Cold
- Page 107 and 108:
Probable Simultaneous Flow Rate Est
- Page 109 and 110:
Water Pressure Requirements Water p
- Page 111 and 112:
Assumed Connection Details Street N
- Page 113 and 114:
Figure 12.5 Typical Direct Water Bo
- Page 115 and 116:
Velocity of Water Services Systems
- Page 117 and 118:
Water Velocity Recommended For Buil
- Page 119 and 120:
13 Chapter Thirteen Chapter 13 - He
- Page 121 and 122:
Design Principles For Heated Water
- Page 123 and 124:
Water Temperature The requirements
- Page 125 and 126:
Figure 13.1 One Pipe Reticulated Sy
- Page 127 and 128:
Figure 13.5 Hot Water Flow and Retu
- Page 129 and 130:
Two pipe - Reverse Return System Th
- Page 131 and 132:
Balancing Heated Water Systems Bala
- Page 133 and 134:
Design Guidelines for Selecting Hea
- Page 135 and 136:
Commercial tariff rates for electri
- Page 137 and 138:
Electric continuous flow - instanta
- Page 139 and 140:
15 Chapter Fifteen Chapter 15 - War
- Page 141 and 142:
The designer must be aware that, no
- Page 143 and 144:
Digital Monitored System A digitall
- Page 145 and 146:
16 Chapter Sixteen Chapter 16 - Pum
- Page 147 and 148:
Cavitation - Process in which small
- Page 149 and 150:
Pump Specifications and Technical D
- Page 151 and 152:
NPSH-curve (Net Positive Suction He
- Page 153 and 154:
Heating Circulation Systems The bes
- Page 155 and 156:
17 Chapter Seventeen Chapter 17 - P
- Page 157 and 158:
Water usage patterns are used to fo
- Page 159 and 160:
Designers need to be cognizant of t
- Page 161 and 162:
https://plumbing.org.au/shop/ gives
- Page 163 and 164:
For instance 30.5m head = 299kPa (s
- Page 165 and 166:
Pipe Friction There are many standa
- Page 167 and 168:
Minimum Residual Head This is the p
- Page 169 and 170:
Waterpipesize Applications The Free
- Page 171 and 172:
H2X Software Solution The process o
- Page 173 and 174:
Figure 17.7 Features of H2X Hydraul
- Page 175 and 176:
Testing and Commissioning The insta
- Page 177 and 178:
Performing the Test The test proced
- Page 179 and 180:
Records Maintaining records of test
- Page 181 and 182:
Industry Terminology Abbreviations,
- Page 183 and 184:
Definitions Access Opening: An open
- Page 185 and 186:
pH: A measure of the acidity or alk
- Page 187 and 188:
A Appendix A Appendix A - Acknowled
- Page 189 and 190:
Australian and International Standa
- Page 191 and 192:
Index A Acknowledgments............
Change language