GT Designer3 Version1 Screen Design Manual (Functions)

Recommendations

Info

(b) Switch the hierarchy using the device specified by [Hierarchy] in [Switching Device] on the Extended tab. Display all the alarms of the hierarchy specified by the device. The following shows an example when the switching device of hierarchy is set to GD110. GD110 2 GD110 1 GD110 0 POINT Occurred Comment Restored Checked -- -- Line1 abend -- -- -- -- Line2 abend -- -- Occurred Comment Restored Checked -- -- Equipment A error -- -- -- -- Equipment B error -- -- -- -- Equipment B error -- -- Occurred Comment Restored Checked 04/06/01 14:25 Pwr. module error 04/06/01 12:10 Control module error 12:25 04/06/01 10:00 Control module error 11:00 04/06/01 09:15 Pwr. module error 10:10 09:55 04/06/01 08:35 Control module error 10:20 09:40 (1) Switching method to the upper alarm hierarchy To switch the hierarchy to the upper alarm hierarchy (general alarms operate the touch switches for advanced user alarm display. middle alarms higher alarms), (6) Description on touch switches for advanced user alarm display (2) Alarm hierarchy specified as the initial display hierarchy To display alarms in hierarchy, it is recommended to specify the highest alarm hierarchy as the initial display hierarchy. If any lower alarm hierarchy is specified as the initial display hierarchy, alarms are displayed with the vertical hierarchies ignored. Example: When the initial display hierarchy is specified to general alarms Occurred Comment Restored Checked 04/06/01 14:25 04/06/01 12:10 04/06/01 11:20 04/06/01 09:00 04/06/01 08:40 Pwr. module error Drive module error Control module error Control module error Control module error 11:00 10:20 12:25 11:20 09:20 08:50 All the alarms belonging to the general hierarchy are displayed. (3) Timing at which alarms are switched to the initial display hierarchy regardless of the hierarchy being displayed When the advanced user alarms (alarm ID) to be displayed are switched or language switching is performed, all the alarms of the hierarchy specified as the initial display hierarchy are displayed. 11 - 86 11.3 Advanced User Alarm Display Power Equipment A Line1 Line2 Equipment B Equipment B Control Control Power Control Equipment A Equipment B Equipment B Power Control Control Power Control Display scope Displays all higher alarms Displays all middle alarms Display scope Displays all general alarms Power Control Control Power Control
(2) Switching displays by device (set in [Switching Device] on the [Extended] tab) Data displayed can be switched by the value of device. The display shown below is available. ( 11.3.3 Setting advanced user alarm display) • Refined display of data by level, group, and alarm ID • Change the comments displayed according to the target user or purpose. • Change the displaying order (descending, ascending and so on). (a) Items to which a switching device can be set Switching device setting usable item *1 The hierarchy, level, and group for alarms are set by the advanced user alarm observation function. 11.3.2 Setting advanced user alarm observation Description Hierarchy *1 All the alarms generated in the specified alarm hierarchy are displayed. Level *1 Alarms at the specified level are displayed. Group *1 Alarms of the specified group are displayed. Priority Level Attribute Advanced User Alarm Observation General Comment Group Middle Comment Group Higher Comment Group The display order is changed between ascending order and descending order. For the sort key, occurrence date/time, restoration date/time, check date/time, comment No., level, group, alarm status (occurred, checked, or restored), occurrence frequency, cumulative time, or down time can be selected. The setting of advanced user alarm observation (alarm ID) displayed by advanced user alarm display can be changed. Multiple sets of alarm data can be displayed by an advanced user alarm display window. The comments displayed when an alarm occurs can be changed for each comment group. The comment displayed can be changed according to the user or purpose. 11.3 Advanced User Alarm Display 11 - 87 9 DATE DISPLAY/TIME DISPLAY 10 COMMENT DISPLAY 11 ALARM 12 LEVEL 13 PANELMETER 14 LINE GRAPH 15 TREND GRAPH 16 BAR GRAPH
Page 1:
Integrated FA Software GT Designer3
Page 4 and 5:
A - 2 CAUTIONS FOR USING THIS SOFTW
Page 6 and 7:
INTRODUCTION Thank you for choosing
Page 8 and 9:
A - 6 6.3.4 GOT internal device....
Page 10 and 11:
A - 8 12.3 Actions ................
Page 12 and 13:
GT Designer3 Version1 Screen Design
Page 14 and 15:
A - 12 30.3.7 Precautions..........
Page 16 and 17:
41. SOUND OUTPUT FUNCTION A - 14 41
Page 18 and 19:
QUICK REFERENCE A - 16 � Creating
Page 20 and 21:
ABBREVIATIONS AND GENERIC TERMS A -
Page 22 and 23:
A - 20 � Option Memory card Abbre
Page 24 and 25:
A - 22 � Others Abbreviations and
Page 26 and 27:
A - 24
Page 29 and 30:
1. FIGURES The following figures ca
Page 31 and 32:
3. Display the dialog box. Double-c
Page 33 and 34:
1.3 Rectangle This function enables
Page 35 and 36:
*4 Figure forms when selecting type
Page 37 and 38:
1.5 Circle This function enables to
Page 39 and 40:
Page 41 and 42:
1.8 Scale This function enables to
Page 43 and 44:
Page 45 and 46:
1.10 Paint This function enables to
Page 47 and 48:
1.11 Import Figure File This functi
Page 49 and 50:
POINT (1) Importing BMP files to GT
Page 51 and 52:
(b) Setting transparent colors(Not
Page 53 and 54:
� Using DXF files (1) Compatible
Page 55 and 56:
POINT Converting data to be importe
Page 57 and 58:
(2) Pasting IGES files Save the set
Page 59 and 60:
1.11.2 Precautions for importing da
Page 61 and 62:
3. There are two ways to specify a
Page 63:
TOUCH SWITCH, LAMP
Page 66 and 67:
� Word Switch 2.4 Setting Word Sw
Page 68 and 69:
2.2 Setting Switch For the switch o
Page 70 and 71:
HINT Lamp Select the item according
Page 72 and 73:
(2) Word The followings can be set
Page 74 and 75:
(5) Station No. When setting the st
Page 76 and 77:
(7) Key Window Display When setting
Page 78 and 79:
� Style tab When [Bit-ON/OFF] or
Page 80 and 81:
� Text tab For touch switches, th
Page 82 and 83:
Text Settings Item Description Mode
Page 84 and 85:
Offset Item Description Model HINT
Page 86 and 87:
(3) Comment group Item Description
Page 88 and 89:
� Extended tab Item Description M
Page 90 and 91:
*1 Simultaneous Press (Prohibition)
Page 92 and 93:
� Trigger tab Set conditions for
Page 94 and 95:
2.3 Setting Bit Switch For the bit
Page 96 and 97:
POINT (1) Touch switch operation wh
Page 98 and 99:
2.4 Setting Word Switch For the wor
Page 100 and 101:
HINT Lamp Select the item according
Page 102 and 103:
Item Description Model Next Screen
Page 104 and 105:
*1 Back (previous/history) Select t
Page 106 and 107:
(c) Setting example for switching t
Page 108 and 109:
(2) When specifying word device Aft
Page 110 and 111:
� Style tab The setting contents
Page 112 and 113:
Item Description Model Lamp (Timing
Page 114 and 115:
*1 Device (Switch station No. to be
Page 116 and 117:
Page 118 and 119:
Item Description Model Switch Actio
Page 120 and 121:
Item Description Model Switch Actio
Page 122 and 123:
POINT When using ladder search sett
Page 124 and 125:
(4) PX Developer Function Call Sett
Page 126 and 127:
(7) Multimedia detail settings By s
Page 128 and 129:
(a) Terminal Server Auto Logon Sett
Page 130 and 131:
2.8 Setting Key Window Display Swit
Page 132 and 133:
Page 134 and 135:
Item Description Model Object Name
Page 136 and 137:
2.10.4 GOT environmental setting (S
Page 138 and 139:
By right-clicking the mouse on an o
Page 140 and 141:
(10) Setting [Repeat the operation
Page 142 and 143:
(3) Setting overlapping actions (ei
Page 144 and 145:
(4) When [Repeat the operation whil
Page 146 and 147:
3.1 Setting Bit Lamp 1. Select [Obj
Page 148 and 149:
� Text tab For the bit lamp, any
Page 150 and 151:
Item Description Model Text Setting
Page 152 and 153:
Text Settings Item Description Mode
Page 154 and 155:
� Script tab For details of scrip
Page 156 and 157:
Shape Item Description Model Use Im
Page 158 and 159:
� Text tab For word lamp, texts d
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
� Operation/Script tab The operat
Page 166 and 167:
3.3 Setting Lamp Area 1. Select [Ob
Page 168 and 169:
3.4 Relevant Settings The lamp is a
Page 170 and 171:
(7) Converting a lamp to a touch sw
Page 173 and 174:
4. GRAPHIC CHARACTERS The following
Page 175 and 176:
KANJI Region *2 Category *2 Setting
Page 177 and 178:
4.2 Logo Text This function enables
Page 179 and 180:
(2) Advanced tab (a) Outline Item D
Page 181 and 182:
(e) Neon Item Description Model Out
Page 184 and 185:
5 - 2 Example Displays numeric valu
Page 186 and 187:
Item Description Model Display Form
Page 188 and 189:
*2 Precautions for format strings T
Page 190 and 191:
*1 States (1) Display for state oth
Page 192 and 193:
Item Description Model KANJI Region
Page 194 and 195:
Page 196 and 197:
5.2 Setting Numerical Input 1. Sele
Page 198 and 199:
Page 200 and 201:
*2 Precautions for format strings T
Page 202 and 203:
� Display Case tab The attribute
Page 204 and 205:
� Extended tab Item Description M
Page 206 and 207:
*1 User ID Set the [User ID] to ena
Page 208 and 209:
Page 210 and 211:
(2) Input object script For details
Page 212 and 213:
5.3 Relevant Settings The numerical
Page 214 and 215:
5.3.3 GOT environmental setting (Sy
Page 216 and 217:
� Precautions for use (1) When nu
Page 218 and 219:
� Precautions for input confirmat
Page 221 and 222:
6.1 Setting ASCII Display 1. Select
Page 223 and 224:
� Extended tab Extended Layer Cat
Page 225 and 226:
Page 227 and 228:
Item Description Model Input Alignm
Page 229 and 230:
� Extended tab Extended Item Desc
Page 231 and 232:
*3 Setting the user ID Cursor movem
Page 233 and 234:
� Script tab (1) Input object scr
Page 235 and 236:
6.3 Relevant Settings The ASCII dis
Page 237 and 238:
6.3.4 GOT internal device (Fundamen
Page 243 and 244:
(3) Specifications of the learning
Page 252 and 253:
6.6 Precautions This section provid
Page 254 and 255:
6 - 36 6.6 Precautions
Page 256 and 257:
7 - 2 � Methods of setting data l
Page 258 and 259:
Item Description Model to to Device
Page 260 and 261:
Bit Mask Bit Shift (b) Data operati
Page 262 and 263:
� Style tab Operational expressio
Page 264 and 265:
(3) State settings of data list In
Page 266 and 267:
Page 268 and 269:
7.3 Actions � Data list function
Page 270:
Page 273 and 274:
Contents Item Description Model Dat
Page 275 and 276:
(3) Date/Time Setting dialog box Pr
Page 277 and 278:
� Style tab Item Description Mode
Page 279 and 280:
*1 User ID (1) When the user ID set
Page 281 and 282:
(2) Value to be stored in a device
Page 283 and 284:
8.2 Relevant Settings The historica
Page 285 and 286:
8.4 Useful Operations/Functions �
Page 287 and 288:
POINT Interaction of the historical
Page 289 and 290:
8.5 Precautions � Precautions for
Page 291 and 292:
9. DATE DISPLAY/TIME DISPLAY � Da
Page 293 and 294:
Item Description Model Shape Settin
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
9.4 Precautions This section explai
Page 303 and 304:
10. COMMENT DISPLAY � Bit comment
Page 305 and 306:
10.1 Setting Bit Comment 1. Select
Page 307 and 308:
� Comment tab Select [Comment Typ
Page 309 and 310:
Comment Comment Item Description Mo
Page 311 and 312:
Comment Item Description Model Disp
Page 313 and 314:
Extended Layer Category Item Descri
Page 315 and 316:
Page 317 and 318:
Shape *1 State Item Description Mod
Page 319 and 320:
� Comment tab Select [Comment Typ
Page 321 and 322:
Comment Comment Item Description Mo
Page 323 and 324:
Comment Preview No. Item Descriptio
Page 325 and 326:
Extended Layer Category Item Descri
Page 327 and 328:
� Operation/Script tab For detail
Page 329 and 330:
(2) Script For details of script se
Page 331 and 332:
Item Description Model Change Attri
Page 333:
ALARM
Page 336 and 337:
11 - 2 � Functions for displaying
Page 338 and 339:
(2) Switching the language Switch t
Page 340 and 341:
� Alarm display operation (1) Cha
Page 342 and 343:
� Display alarm only when alarm o
Page 344 and 345:
� User-Setting of alarm monitorin
Page 346 and 347:
(2) Output to a CSV file Alarm data
Page 348 and 349:
11.1.1 Alarm function This section
Page 350 and 351:
(3) Alarm history display When a us
Page 352 and 353:
11.1.2 Advanced alarm function The
Page 354 and 355:
POINT Alarm ID As the multiple sets
Page 356 and 357:
(3) Settings for whether to popup o
Page 358 and 359:
11.3 Advanced User Alarm Display Th
Page 360 and 361:
(2) Collection flow and collection
Page 362 and 363:
• Historical mode In this mode, t
Page 364 and 365:
• Cumulative mode The information
Page 366 and 367:
(3) Retention and clear of collecte
Page 368 and 369:
(b) Status observation during writi
Page 370 and 371: (5) Converting alarm log files The
Page 372 and 373: 1) 2) 3) 4) 5) 6) 7) 8) (6) Content
Page 374 and 375: � Setting the advanced user alarm
Page 376 and 377: POINT 2. By setting the [Switching
Page 378 and 379: � Creating a Unicode text file/CS
Page 380 and 381: � Advanced User Alarm Observation
Page 382 and 383: (2) Device tab Set the timing for c
Page 384 and 385: 1. *1 Method of setting the comment
Page 386 and 387: *4 Method of displaying the comment
Page 388 and 389: *6 Copy Advanced User Alarm Observa
Page 390 and 391: Item Description Model Writing Erro
Page 392 and 393: Item Description Model Display Type
Page 394 and 395: � Display tab Set the data displa
Page 396 and 397: Item Description Model Contents Dat
Page 398 and 399: � Text tab Set the font to displa
Page 400 and 401: � Style tab Set the ruled line ty
Page 402 and 403: Item Description Model Switching De
Page 404 and 405: • Setting method Set a user ID fo
Page 406 and 407: � Trigger tab Set conditions for
Page 408 and 409: Item Description Model Device Comme
Page 410 and 411: 11.3.4 Relevant settings The advanc
Page 412 and 413: Line1 error Line2 error Upper hiera
Page 414 and 415: HINT (c) Alarm Classification accor
Page 416 and 417: (3) Action when buffer is full If t
Page 418 and 419: � Advanced user alarm display Pow
Page 422 and 423: (b) Display example Alarms are refi
Page 424 and 425: (4) Set or change table titles and
Page 426 and 427: (6) Description on touch switches f
Page 428 and 429: Display detail Move to the lower hi
Page 430 and 431: HINT (1) Touch switches operating d
Page 432 and 433: (b) Priority order for using the SR
Page 434 and 435: 11.3.6 Precautions This section exp
Page 436 and 437: (b) When masking is not applied 0 0
Page 438 and 439: (2) Alarm observation during saving
Page 440 and 441: (9) Display of occurrence time, che
Page 442 and 443: 11.4 Advanced System Alarm Display
Page 444 and 445: (2) Collection flow and collection
Page 446 and 447: (c) Examples of alarm display This
Page 448 and 449: (3) Alarm restoration The following
Page 450 and 451: HINT Clearing alarm data The follow
Page 452 and 453: (c) File name to be saved and savin
Page 454 and 455: (b) How to create Unicode text file
Page 456 and 457: (c) Alarm display order Set the ord
Page 458 and 459: (2) Operations by touch switches Va
Page 460 and 461: Basic Buffering Item Description Mo
Page 462 and 463: Writing Error Notification Device I
Page 464 and 465: Item Description Model Touch Mode N
Page 466 and 467: � Display tab Set the data displa
Page 468 and 469: (1) Date/Time Setting dialog box Se
Page 470 and 471:
� Style tab Set the ruled line ty
Page 472 and 473:
*1 Priority display attribute Store
Page 474 and 475:
Page 476 and 477:
Item Description Model Device Alarm
Page 478 and 479:
11.4.4 Relevant settings The advanc
Page 480 and 481:
(c) Buffering size The buffering si
Page 482 and 483:
(2) Setting of alarm status display
Page 484 and 485:
(5) Description on touch switches f
Page 486 and 487:
HINT (1) Touch switches operating d
Page 488 and 489:
(b) Priority order for using the SR
Page 490 and 491:
11.4.6 Precautions This section exp
Page 492 and 493:
(4) If the same data exists in the
Page 494 and 495:
(10) Error when the alarm log file
Page 496 and 497:
11.5 Alarm History Display The time
Page 498 and 499:
11.5.1 Alarm history settings Selec
Page 500 and 501:
Item Description Model Alarm settin
Page 502 and 503:
*2 Import/Export The exported CSV f
Page 504 and 505:
(2) Edit Alarm Range dialog box Set
Page 506 and 507:
� Option tab Configure the histor
Page 508 and 509:
*1 Saving data in the CSV format (1
Page 510 and 511:
11.5.2 Alarm history display settin
Page 512 and 513:
*1 Display Start Row If the number
Page 514 and 515:
Page 516 and 517:
11.5.3 Relevant settings The alarm
Page 518 and 519:
Example) Examples of alarm display
Page 520 and 521:
(b) Operation for listing the same
Page 522 and 523:
� Detail display (1) Usable scree
Page 524 and 525:
11.5.5 Useful operations and functi
Page 526 and 527:
*1 Resetting user alarms For detail
Page 528 and 529:
(7) Display of occurred time, check
Page 530 and 531:
11.6.1 Settings 1. Select [Object]
Page 532 and 533:
*1 Display Method of Comment Window
Page 534 and 535:
Page 536 and 537:
Page 538 and 539:
11.6.3 Actions This function displa
Page 540 and 541:
� Details of display (only for [P
Page 542 and 543:
HINT To match the user alarm displa
Page 544 and 545:
POINT (1) The timing when the data
Page 546 and 547:
Move cursor upward Move cursor down
Page 548 and 549:
11.6.5 Precautions This section pro
Page 550 and 551:
11.7 System Alarm Display System al
Page 552 and 553:
� System Alarm Display dialog box
Page 554 and 555:
11.7.3 Actions � Types of system
Page 556 and 557:
11.8 Advanced Alarm Popup Display A
Page 558 and 559:
(2) Settings required for using adv
Page 560 and 561:
� Selection of display method The
Page 562 and 563:
Item Description Model Display Posi
Page 564 and 565:
� Text Style tab Set the text for
Page 566 and 567:
� Extended tab Perform the settin
Page 568 and 569:
*2 Priority display attribute Store
Page 570 and 571:
Device Item Description Model Alarm
Page 572 and 573:
11.8.3 Relevant settings The advanc
Page 574 and 575:
POINT (1) Hierarchies that can be s
Page 576 and 577:
� Switching of alarm hierarchies
Page 578 and 579:
GD110 2 GD110 1 GD110 0 (2) Switch
Page 580 and 581:
� Specify font, text color, and b
Page 582 and 583:
� Writing alarm data into device
Page 584 and 585:
(2) When switching comment display
Page 586 and 587:
� Precautions for use (1) When an
Page 588 and 589:
(5) Refining-display of alarms when
Page 590 and 591:
11.9.1 Settings Select [Common] [Al
Page 592 and 593:
(1) Date/Time Setting dialog box Se
Page 594 and 595:
11.9.3 Actions � Alarm types and
Page 596 and 597:
11.9.4 Precautions � Precautions
Page 599 and 600:
12. LEVEL This function fills the s
Page 601 and 602:
HINT When internal position mark (
Page 603 and 604:
Page 605 and 606:
Page 607 and 608:
Page 609 and 610:
12.2 Relevant Settings The level is
Page 611 and 612:
12.4 Precautions This section expla
Page 613 and 614:
13. PANELMETER This function enable
Page 615 and 616:
Item Description Model Meter Format
Page 617 and 618:
Common Settings of Display Position
Page 619 and 620:
*1 State (1) Display for state othe
Page 621 and 622:
Page 623 and 624:
13.2 Relevant Settings The panelmet
Page 625 and 626:
14. LINE GRAPH This function enable
Page 627 and 628:
Device Item Description Model Set t
Page 629 and 630:
Item Description Model Scale Settin
Page 631 and 632:
*1 Clear ON trigger recognition tim
Page 633 and 634:
*1 If the graph display is not upda
Page 635 and 636:
Page 637 and 638:
14.2 Relevant Settings The line gra
Page 639 and 640:
� Precautions for the line graph
Page 641:
15. TREND GRAPH This function is us
Page 644 and 645:
*1 Clear ON trigger recognition tim
Page 646 and 647:
Scale Settings Item Description Mod
Page 648 and 649:
Page 650 and 651:
*2 When settings for Collect data o
Page 652 and 653:
Page 654 and 655:
HINT Display of values exceeding th
Page 656 and 657:
Page 658 and 659:
� Data tab Item Description Model
Page 660 and 661:
Scale Settings Item Description Mod
Page 662 and 663:
Page 664 and 665:
*1 When settings for Collect data o
Page 666 and 667:
Page 668 and 669:
HINT Display of values exceeding th
Page 670 and 671:
Page 672 and 673:
Page 674 and 675:
Page 676 and 677:
Page 678 and 679:
17.2 Relevant Settings The statisti
Page 680 and 681:
Page 682 and 683:
Page 684 and 685:
Page 686 and 687:
Page 688 and 689:
Page 690 and 691:
18.2 Relevant Settings The statisti
Page 692 and 693:
Page 694 and 695:
19.1 Settings 1. Select [Object] [G
Page 696 and 697:
Page 698 and 699:
Attribute *1 State Item Description
Page 700:
Page 703 and 704:
Page 705 and 706:
19.2 Relevant Settings The scatter
Page 707 and 708:
� Store memory Executing the foll
Page 709 and 710:
(2) Initialization timing of accumu
Page 711 and 712:
20. HISTORICAL TREND GRAPH This fun
Page 713 and 714:
Display Format Device Item Descript
Page 715 and 716:
Item Description Model Lower Limit
Page 717 and 718:
POINT Types to be selected for data
Page 719 and 720:
Item Description Model Vertical Gri
Page 721 and 722:
� Extended tab Set the security,
Page 723 and 724:
*2 Time device (1) How the data is
Page 725 and 726:
(2) Operation example The following
Page 727 and 728:
20.3.2 Historical trend graph setti
Page 729 and 730:
(5) Outputting the date data to a d
Page 731 and 732:
Touch switch Key code Description G
Page 733 and 734:
(9) Precautions for specifying a lo
Page 735:
PARTS
Page 738 and 739:
21 - 2 POINT Parts displayed by Par
Page 740 and 741:
Display Mode Alignment Item Descrip
Page 742 and 743:
(1) Image File Setting Dialog Box I
Page 744 and 745:
Page 746 and 747:
21.2 Word Parts Settings 1. Select
Page 748 and 749:
Alignment Range Item Description Mo
Page 750 and 751:
*3 Parts switching method State set
Page 752 and 753:
Page 754 and 755:
Page 756 and 757:
Item Description Model Display Mode
Page 758 and 759:
� Extended tab Set the security a
Page 760 and 761:
21.4 Parts Settings Select [Common]
Page 762 and 763:
21.6 Actions � Display method of
Page 764 and 765:
(c) Display example The following s
Page 766 and 767:
� Parts No. The displayable parts
Page 768 and 769:
When the "Parts type" is "Part" Dis
Page 770 and 771:
22 - 2 (3) Fixed parts movement 22.
Page 772 and 773:
Item Description Model Move Format
Page 774 and 775:
*1 Line Set the line to be the part
Page 776 and 777:
Page 778 and 779:
22.2 Word Parts Settings Select [Ob
Page 780 and 781:
Alignment Range Item Description Mo
Page 782 and 783:
*3 State (1) When states are overla
Page 784 and 785:
� Extended tab Set the security,
Page 786 and 787:
Page 788 and 789:
22.3 Fixed Parts Settings Select [O
Page 790 and 791:
*2 Line Item Description Model Deta
Page 792 and 793:
Page 794 and 795:
22.4 Setting of Parts Move Route (C
Page 796 and 797:
22.5 Relevant Settings The parts mo
Page 798 and 799:
(2) Line Move parts along lines bet
Page 800 and 801:
� Display method of a BMP/JPEG fi
Page 802 and 803:
POINT (1) When specifying a part nu
Page 804 and 805:
Page 806 and 807:
Error messages.....................
Page 808 and 809:
Index-4
Page 810 and 811:
Print Date *Manual Number Revision
Page 812 and 813:
Page 814:
GOT is a registered trademark of Mi
Page 817:
Integrated FA Software GT Designer3
Page 820 and 821:
A - 2 CAUTIONS FOR USING THIS SOFTW
Page 822 and 823:
INTRODUCTION Thank you for choosing
Page 824 and 825:
A - 6 6.3.4 GOT internal device....
Page 826 and 827:
A - 8 12.3 Actions ................
Page 828 and 829:
GT Designer3 Version1 Screen Design
Page 830 and 831:
A - 12 30.3.7 Precautions..........
Page 832 and 833:
41. SOUND OUTPUT FUNCTION A - 14 41
Page 834 and 835:
QUICK REFERENCE A - 16 � Creating
Page 836 and 837:
ABBREVIATIONS AND GENERIC TERMS A -
Page 838 and 839:
A - 20 � Option Memory card Abbre
Page 840 and 841:
A - 22 � Others Abbreviations and
Page 842 and 843:
A - 24
Page 845 and 846:
23. OPERATION LOG FUNCTION Operatio
Page 847 and 848:
23.1 Settings 1. Select [Common] Se
Page 849 and 850:
POINT When recording the operation
Page 851 and 852:
23.2.2 Display and process This sec
Page 853 and 854:
(1) GOT startup Item Description It
Page 855 and 856:
(9) Station No. switching Item Desc
Page 857 and 858:
(12) Numerical input Item Descripti
Page 859 and 860:
23.2.3 Creating Unicode text file/C
Page 861 and 862:
� Precautions for use (1) When us
Page 863 and 864:
24. LOGGING FUNCTION The logging fu
Page 865 and 866:
24.1.2 Logging setting (1) Basic ta
Page 867 and 868:
(2) Device tab Target devices of lo
Page 869 and 870:
*3 Adjusting the column width When
Page 871 and 872:
*1 Date and time settings Set the d
Page 873 and 874:
POINT (1) For max. No. of device po
Page 875 and 876:
(2) Full notification signal device
Page 877 and 878:
(b) Priority order for using the SR
Page 879 and 880:
24.4.1 File save mode The file save
Page 881 and 882:
(2) When using the file terminal tr
Page 883 and 884:
POINT (1) Memory card installation
Page 885 and 886:
� Operating by the utility By usi
Page 887 and 888:
24.4.4 Creating a Unicode text file
Page 889 and 890:
Page 891 and 892:
� Precautions for use (1) Saving
Page 893 and 894:
(5) Integrity of the device values
Page 895:
RECIPE
Page 898 and 899:
25 - 2 1. (2) Using the recipe file
Page 900 and 901:
25 - 4 POINT 8. Convert the edited
Page 902 and 903:
� Max. No. of recipes Multiple re
Page 904 and 905:
(b) GT Designer3 setting When setti
Page 906 and 907:
� Notifying the process status to
Page 908 and 909:
� Recipe Set the data for the rec
Page 910 and 911:
*1 Import/Export The exported CSV f
Page 912 and 913:
POINT (1) Memory card or D drive ch
Page 914 and 915:
25.2.3 Precautions This section exp
Page 916 and 917:
� Advanced Recipe List Select [Co
Page 918 and 919:
Item Description Model File Convert
Page 920 and 921:
*1 Import/Export The exported Unico
Page 922 and 923:
� Block The block is setting unit
Page 924 and 925:
25.3.3 Reading or writing of device
Page 926 and 927:
(b) Setting a target device that va
Page 928 and 929:
(2) Creating in the utility The fol
Page 930 and 931:
3. Display or edit the converted Un
Page 932 and 933:
(2) How to create a Unicode text fi
Page 934 and 935:
(2) Operation for executing the rec
Page 936 and 937:
(2) When the device value is not ov
Page 938 and 939:
POINT • At being faulty completed
Page 940 and 941:
(10) Recipe device setting value Wh
Page 942 and 943:
(4) When the trigger conditions are
Page 944 and 945:
(13) Advanced recipe file conversio
Page 947 and 948:
26. DEVICE DATA TRANSFER FUNCTION T
Page 949 and 950:
� Device data transfer (1) Basic
Page 951 and 952:
*1 Import/Export The exported Unico
Page 953 and 954:
26.1.1 Control of device data trans
Page 955 and 956:
26.2 Relevant Settings The device d
Page 957 and 958:
� External notification device Th
Page 959 and 960:
� Precautions for use (1) Device
Page 961 and 962:
(b) When trigger conditions for dif
Page 963 and 964:
27. STATUS OBSERVATION FUNCTION Thi
Page 965 and 966:
� Trigger/Action (1) Trigger tab
Page 967 and 968:
*1 Fixed and Indirect When [Fixed]
Page 969 and 970:
Page 971 and 972:
28. TRIGGER ACTION FUNCTION The tri
Page 973 and 974:
� Trigger/Action (1) Trigger tab
Page 975 and 976:
29. TIME ACTION FUNCTION The time a
Page 977 and 978:
� Time action setting (1) Time ta
Page 979 and 980:
29.2 Actions To control the time ac
Page 981 and 982:
� Action example for the external
Page 983 and 984:
(3) When using external control Whe
Page 985:
SCRIPT FUNCTION
Page 988 and 989:
� Compatibility with commercially
Page 990 and 991:
POINT Precautions for setting a scr
Page 992 and 993:
� Instructions for assignment del
Page 994 and 995:
(2) Assignment delay with offset fu
Page 996 and 997:
30.2 Project Script, Screen Script
Page 998 and 999:
*1 Update timing when the trigger t
Page 1000 and 1001:
Input Navigation *1 Import/Export I
Page 1002 and 1003:
(4) Script file list The registered
Page 1004 and 1005:
� Script symbol tab / Script symb
Page 1006 and 1007:
� Option tab Set the script data
Page 1008 and 1009:
30.2.2 Settings and procedure for e
Page 1010 and 1011:
Function executing Order Screen scr
Page 1012 and 1013:
30.2.4 Control structure This secti
Page 1014 and 1015:
(3) Arithmetic (4) Bit device (5) A
Page 1016 and 1017:
Function Description acos atan abs
Page 1018 and 1019:
HINT Function Description #pragma f
Page 1020 and 1021:
30.2.5 Applicable data and represen
Page 1022 and 1023:
HINT Devices that can be monitored
Page 1024 and 1025:
*2 How to use offset The offset is
Page 1026 and 1027:
(1) String input function (ASCII co
Page 1028 and 1029:
• Type specifier The type specifi
Page 1030 and 1031:
� Representing bit device (system
Page 1032 and 1033:
(4) Precautions (a) Data type of th
Page 1034 and 1035:
*1 Error code Error codes stored in
Page 1036 and 1037:
� Data type conversion function T
Page 1038 and 1039:
� Lamps which change the display
Page 1040 and 1041:
� Password input screen with time
Page 1042 and 1043:
(2) File read function (file_read)
Page 1044 and 1045:
(6) File copy function (file_copy)
Page 1046 and 1047:
(2) String output function (ASCII c
Page 1048 and 1049:
(2) Precautions for using bmov and
Page 1050 and 1051:
(h) Precautions for specifying fold
Page 1052 and 1053:
(g) Number of significant digits fo
Page 1054 and 1055:
� Script solution examples (1) Re
Page 1056 and 1057:
30.3 Object Script This section exp
Page 1058 and 1059:
� Script tab and operation/script
Page 1060 and 1061:
� Script tab of switch object scr
Page 1062 and 1063:
*1 Import/Export For the exported t
Page 1064 and 1065:
� Object script symbol Select [Co
Page 1066 and 1067:
� Precautions when executing the
Page 1068 and 1069:
30.3.3 Actions and settings This se
Page 1070 and 1071:
� Execution status Object scripts
Page 1072 and 1073:
For the display object script, some
Page 1074 and 1075:
link *2 highlight *2 part_no *2 30
Page 1076 and 1077:
30 - 90 30.3 Object Script Property
Page 1078 and 1079:
POINT Valid duration of changed obj
Page 1080 and 1081:
(a) Argument 30 - 94 30.3 Object Sc
Page 1082 and 1083:
HINT Drawing results of circle / el
Page 1084 and 1085:
� Object properties For the objec
Page 1086 and 1087:
� Showing/hiding the input/touch
Page 1088 and 1089:
(3) Program examples (a) Operation
Page 1090 and 1091:
� Precautions for object property
Page 1092 and 1093:
30.4 Troubleshooting The script fun
Page 1094 and 1095:
� Object script Additional descri
Page 1096 and 1097:
(2) Property Select the data format
Page 1098 and 1099:
Error code *1 Error Definition 116
Page 1100 and 1101:
Address Item Description GS14 Scrip
Page 1102 and 1103:
(2) Items for the GOT special regis
Page 1104 and 1105:
� Error code list (1) Project scr
Page 1106 and 1107:
(2) Object script Error Code Error
Page 1108 and 1109:
� Error category of object script
Page 1110 and 1111:
30 - 124 30.4 Troubleshooting
Page 1113 and 1114:
31. BARCODE FUNCTION The barcode fu
Page 1115 and 1116:
Item Description Model Function Set
Page 1117 and 1118:
31.2 Relevant Settings The barcode
Page 1119 and 1120:
� Header/terminator The header or
Page 1121 and 1122:
� Action timing of the barcode fu
Page 1123 and 1124:
Page 1126 and 1127:
POINT Channel No. restrictions To u
Page 1128 and 1129:
(1) Detail Setting Configure the RF
Page 1130 and 1131:
32.2.2 GOT internal device (Fundame
Page 1132 and 1133:
� Order of writing data to contro
Page 1134 and 1135:
� RFID controller signal, send da
Page 1136 and 1137:
32 - 12 32.3 Actions 1. Set the RFI
Page 1138 and 1139:
(c) Sequence program example (When
Page 1140 and 1141:
(c) Sequence program example (For Q
Page 1142 and 1143:
� Directly inputting data to the
Page 1144 and 1145:
� Precautions for directly inputt
Page 1146 and 1147:
33.1.1 Settings The following shows
Page 1148 and 1149:
9. The Found New Hardware Wizard sc
Page 1150 and 1151:
� Operation of mouse pointer The
Page 1152 and 1153:
33.2 Remote Personal Computer Opera
Page 1154 and 1155:
33.2.1 Settings The following shows
Page 1156 and 1157:
� PC Remote Operation dialog box
Page 1158 and 1159:
(5) Settings 1. When UltraVNC does
Page 1160 and 1161:
(c) Settings Set the following item
Page 1162 and 1163:
33.2.2 Actions � Personal compute
Page 1164 and 1165:
33.2.3 Precautions � Precautions
Page 1167 and 1168:
34.1 Settings The following shows h
Page 1169 and 1170:
POINT (1) Number of the connecting
Page 1171 and 1172:
34.2 Relevant Settings The VNC ® s
Page 1173:
POINT When the remote screen does n
Page 1176 and 1177:
34.4 Precautions � Setting requir
Page 1178 and 1179:
Page 1180 and 1181:
35.1 Settings Select [Common] [Peri
Page 1182 and 1183:
� Setting items of [Video/RGB Inp
Page 1184 and 1185:
35.3 Actions � Displaying a video
Page 1186 and 1187:
� Placing video window on overlap
Page 1188 and 1189:
(4) Invalid area of a touch switch
Page 1190 and 1191:
� Transparent processing (1) Disp
Page 1192 and 1193:
(b) In a normal state, small-size v
Page 1194 and 1195:
Video window 1 Video window 1 35 -
Page 1196 and 1197:
Page 1198 and 1199:
Page 1200 and 1201:
36 - 2 POINT (1) System configurati
Page 1202 and 1203:
Item Description Model Video settin
Page 1204:
� Playback/External Notification
Page 1207 and 1208:
� Display Setting tab Configure t
Page 1209 and 1210:
36.2 Actions � Specifications (1)
Page 1211:
� Recording video image By connec
Page 1214 and 1215:
(4) Playing video file The GOT can
Page 1216 and 1217:
(b) Displaying video file list or s
Page 1218 and 1219:
(3) On GOT (a) Inserting CF card In
Page 1220 and 1221:
2. When an alarm occurs, the advanc
Page 1222 and 1223:
� How to install (1) Installation
Page 1224 and 1225:
� Screen configurations The scree
Page 1226 and 1227:
Item Description Project Click this
Page 1228 and 1229:
(c) Storing project file To store t
Page 1230 and 1231:
(5) Searching for alarm data The GO
Page 1232 and 1233:
Error message Cause Corrective acti
Page 1234 and 1235:
(4) Unit software version of multim
Page 1236 and 1237:
Page 1238 and 1239:
Page 1240 and 1241:
Action List Add Action Item Descrip
Page 1242 and 1243:
37.2 Relevant Settings The operatio
Page 1244 and 1245:
Page 1246 and 1247:
Page 1248 and 1249:
38.3 Actions � Displaying the RGB
Page 1250:
� Screen save of the RGB screen W
Page 1253 and 1254:
Page 1255 and 1256:
39. REPORT FUNCTION The report func
Page 1257 and 1258:
� Printing tab Set the print trig
Page 1259 and 1260:
� Data Collection tab Set the dat
Page 1261 and 1262:
Item Description Model Common Print
Page 1263 and 1264:
(2) Precautions Line attributes can
Page 1265 and 1266:
Operation Type Bit Mask Bit Shift (
Page 1267 and 1268:
� Word comment print arrangement
Page 1269 and 1270:
HINT Printable area Number of lines
Page 1271 and 1272:
39.5 Actions � Operation of the r
Page 1273 and 1274:
3. Set print layout For details of
Page 1275 and 1276:
(2) Usable printer For the usable p
Page 1277 and 1278:
40. HARD COPY FUNCTION The hard cop
Page 1279 and 1280:
Item Description Model Start Trigge
Page 1281 and 1282:
40.2 Relevant Settings The hard cop
Page 1283 and 1284:
41. SOUND OUTPUT FUNCTION The funct
Page 1285 and 1286:
HINT (1) Creating sound files Recor
Page 1287:
APPENDICES
Page 1290 and 1291:
Appendix2 Precautions for Option Fu
Page 1292 and 1293:
Appendix4 Type of Data That Can Be
Page 1294 and 1295:
Error messages.....................
Page 1296 and 1297:
Index-4
Page 1298 and 1299:
Page 1300 and 1301:
Page 1302:
GOT is a registered trademark of Mi
show all

GT Designer3 Version1 Screen Design Manual (Functions)

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?