ABT20PANEL_I_E_No1_9720342

More documents

Recommendations

Info

3.2 Parameter settings screen P ○ S1 ○ S2 ○ ▲ □ ▼ □ Display P □ T ▲ □ D □ R ▼ □ * Pressing the R switch returns to the first process. 1: ABT ON ■ Screen 1: Process and sewing patterns Press T. A01 015 STITCH CHAIN LENGTH Screen A: A01 to A04 Press T. B01 020 TIMER MOTOR&K CONTROL Screen B: B01 to B14 Press T. C01 000 STITCH MESH COUNTER Screen C: C01 to C15 4. Screen A displays and their descriptions 2 Call the numbers of the parameters required. P ○ S1 ○ S2 ○ ▲ □ ▼ □ Display P □ T ▲ □ D □ R ▼ □ 3 Use these buttons to enter the setting values. 1: ABT ON ■ 1 Call screen A using these buttons. A01 050 STITCH CLAMP STITCH Adjust the strength with which the thread chain is pulled in during backtacking. Press P. A02 015 STITCH CHAIN LENGTH Adjust the length of the thread chain to sew into the seamat beginning of sewing using the number of stitches. Press P. Press P. Press P. A03 035 STITCH SEW END STITCH A04 OFF ON/OFF AUTO PF UP A05 ON ON/OFF KEY LOCK Set the number of stitches to be sewn until the machine stops after the fabric sensor not detected the material. The presser foot automatically rises at the end of sewing, and the machine stands by until the next fabric is put in place. (Either ON auto or OFF manual can be selected.) In order to prevent misoperation, only screens B and C are locked when ON is selected. (Either ON or OFF can be selected.) 4
5. Screen B displays and their descriptions 2 Call the numbers of the parameters required. P ○ S1 ○ S2 ○ ▲ □ ▼ □ Display □ T ▲ □ P □ R ▼ □ 3 Use these buttons to enter the setting values. D 1: ABT ON ■ 1 Call screen B using these buttons Press P. Press P. Press P. Press P. Press P. Press P. Press P. Press P. Press P. Press P. Press P. Press P. Press P. B01 350 TIMER MOTOR&K CONTROL B02 070 TIMER PF UP TIMER B03 070 TIMER BLOW DELAY TIMER B04 090 TIMER SUC. OPEN TIMER B05 020 TIMER BLOW CHAIN TIMER B06 002 STITCH FRONT TR STITCH B07 008 STITCH REAR TR STITCH B08 005 STITCH FRONT TR S.(OFF) B09 004 STITCH FRONT TONGUE B10 008 STITCH REAR TONGUE B11 100 TIMER SUC. STOP DELAY B12 150 TIMER PF 2 DOWN TIMER B13 005 STITCH CHAIN CUT STITCH B14 030 STITCH FRONT K STITCH When sewing is finished, adjust the amount of thread chain remaining around the stitch plate tongue. When the large amount of thread chain remains around the tongue, reduce the setting value. Readjustment is necessary when changing the sewing speed. When increasing the sewing speed, reduce the setting value. Adjust whether the presser foot rises before or after the machine stops. (Time adjustment) Adjust the wait time until blowing back from K2 starts after the presser foot rises. (Time adjustment) Adjust the time during which the thread chain clamp (right) is open when the thread chain is caught. (Time adjustment) Note: Set at 50 greater than parameter B05. Adjust the time during which the thread chain is blown back from the K2 device. (Time adjustment) Note: Set at 50 smaller than parameter B04. Adjust the timing at which the thread at the beginning of sewing is tightened when backtacking is used (ABT/ON). Note: This timing differs depending on the stitch length and machine speed. (Stitch number adjustment) Adjust the timing at which the thread is loosened at the end of sewing. Note: This timing differs depending on the stitch length and machine speed. (Stitch number adjustment) Adjust the timing at which the thread at the beginning of sewing is tightened when performing plain sewing (ABT/OFF). Note: This timing differs depending on the stitch length and machine speed. (Stitch number adjustment) Adjust the timing at which the movable middle stitch plate tongue of the stitch plate moves forward at the beginning of sewing. (Stitch number adjustment) Note: This timing differs depending on the stitch length and machine speed. (Stitch number adjustment) Adjust the timing at which the movable middle stitch plate tongue of the stitch plate moves backward at the end of sewing. (Stitch number adjustment) Note: This timing differs depending on the stitch length and machine speed. (Stitch number adjustment) Adjust the time during which the suction pipe sucks in the thread chain. (Time adjustment) Adjust the time until the presser foot moves down after the thread chain is caught. (Time adjustment) Set the number of stitches the thread chain clamp (left) moves to the right so that the thread chain with the length for sewing into the seam is cut. Adjust the length of time that the K device sucks the thread chain at the beginning of sewing when performing plain sewing (ABT/OFF). Note: This timing differs depending on the stitch length and machine speed. (Stitch number adjustment) 5
Page 1 and 2: Instruction Manual AUTOMATIC BACK T
Page 3 and 4: 1. Check out the following prior to
Page 5: ★ Example of process settings P
Page 9 and 10: 7. Starting backtacking Before proc
Page 11 and 12: 9. Troubleshooting Q&A Q A See 1

ABT20PANEL_I_E_No1_9720342

Create successful ePaper yourself

Delete template?

Save as template?