3 Wireless Remote Control CZone LCD QVGA ... - BUKH Bremen

More documents

Recommendations

Info

TM CZone Net wor k Control and Monitor ing Sys tem SWITCH CoNTRoL INTERFACE The Switch Control Interface (SCI) provides an interface between the CZone network and traditional mechanical switches that manufacturers and users are familiar with. This interface converts the signal from those switches into the Control Area Network (CAN) signal needed across a digital network. No need to change existing designs. Diagnostics are important. Fault codes are provided to quickly identify issues with the network or switches. Information is provided on the Switch Control Interface as well as sent to the CZone Display Interface. The SCI simplifies your wiring, supports your existing choice of switches, protects against failures and allows for expanding installation options. Backlighting and systems in operation lights are dimmable to ensure your night vision is not impared by bright lights on your control area, level control of these can be linked to the backlighting level of any Display Interfaces in close proximity of the SCI. GENERAL SPECIFICATIoNS: • Single switch position can control multiple OI channels • Attaches to switch panels via custom SCI cable • Multiple SCI switches can control single OI channel • Output for backlighting of switch labels (dimmable) • Outputs systems on and function/ fault codes to systems on LED of switches (dimmable) • H 100mm (3”29/ 32) x W156mm (6”3/ 32) x D 42mm (1”5/ 8) • IPX5 water ingress protection • Programmable switch types • 8 inputs per module (16 individual controls) • Sequential button press functionality 8-Way Connector Bank for SCI Cable Assembly to Switches Waterproof Cable Seal 8 LEADING ELECTRICAL DESIGN PART# DESCRIPTIoN 80-911-0011-00 Switch Control Interface w/seal 80-911-0012-00 Switch Control Interface only NMEA 2000 Connector
SIGNAL INTERFACE The Signal Interface (SI) connects CZone to your external sensors, alarms and switching devices. The SI allows intelligent, automated operation of circuits depending on the state of the input. For example, the SI can be easily programmed to allow a fluid transfer pump and an alarm to turn on simultaneously when the SI detects that a low tank level has been reached. Connect standard switches to the SI to allow control of CZone outputs. The module provides LED status indications for each input. This allows fast diagnostics while providing information back to CZone’s Display Interface. GENERAL SPECIFICATIoNS: • Accepts inputs from traditional switch types being used to control outputs • Accepts inputs from switches to trigger alarm i.e. high water float switch • Accepts inputs from industry standard tank senders (0-5V, 10- 180Ohm, 240-33Ohm)” • Accepts inputs from general voltaic or resistive signals can be used for controlling outputs or to display a physical position i.e. show a hatch is partially open • LED status indicators for each input • H 100mm (3”29/32) x W156mm (6”3/32) x D 42mm (1”5/8) • IPX5 water ingress protection Terminal Block CZone Net wor k Control and Monitor ing Sys tem Signal Status Indicator Waterproof Cable Seal LEADING ELECTRICAL DESIGN PART# DESCRIPTIoN 80-911-0013-00 Signal Interface w/seals, connector 80-911-0014-00 Signal Interface only CAN Network Status Indicator NMEA 2000 Connector 9 TM
Page 1 and 2: Panel Configurator Create, design a
Page 3 and 4: EA 2000 twork NEW CZone decentraliz
Page 5: CZone Net wor k Control and Monito
Page 9 and 10: ouTPuT INTERFACE The Output Interfa
Page 11 and 12: Historically, generating a configur
Page 13 and 14: Cable Gland for SCI Blk Silicon # 8
Page 15 and 16: 905NM NC36NM 904NMH 906NMH LEADING
Page 17 and 18: 906A 907A LEADING ELECTRICAL DESIGN
Page 19 and 20: M44D M32D M28D LEADING ELECTRICAL D
Page 21 and 22: Range HigHligHts All available in 1
Page 23 and 24: Range HigHligHts Spacing compliance
Page 25 and 26: NEW Panel Configurator LEADING ELEC
Page 27 and 28: AC Power Meter Specifications: 2.8
Page 29 and 30: AC Volts Functions Specifications:
Page 31 and 32: 19.64 [3/4"] 84.88 [3 5/16"] Specif
Page 33 and 34: The BEP Detectors use microprocesso
Page 35 and 36: MS1 Analog Battery Condition Meter
Page 37 and 38: Range HigHligHts Replaceable clip-o
Page 39 and 40: 16mm (.6") 1000-6W 40mm (1.6") 1000
Page 41 and 42: Range HigHligHts Essential circuits
Page 43 and 44: 701S Mini Battery Selector Switch T
Page 45 and 46: Due to the increased load requireme
Page 47 and 48: Wiring diagrams indicative of insta
Page 49 and 50: Single Engine, Two Battery Banks 71
Page 51 and 52: Manual Clusters using Motorized VSR
Page 53 and 54: Single Engine Dual Engine 80-716-00
Page 55 and 56: Twin outboard, Three Battery Banks
Page 57 and 58:
The CC-805T is supplied pre-wired w
Page 59 and 60:
709-300/BD Flexible links are suppl
Page 61 and 62:
Easy to install, with supplied moun
Page 63 and 64:
Range HigHligHts Now with easy-fit
Page 65 and 66:
708 Terminal Links 708-42.5 708-62.
Page 67 and 68:
Multi-purpose Bus Bar BB-6W-2 Multi
Page 69 and 70:
LEADING ELECTRICAL DESIGN Labels Ci
Page 71 and 72:
CSP6 ACCESSoRIES ANCHoR LIGHT ACCES
Page 73 and 74:
B/PUMP AFT LABEL SET SET-G2-1 ACCES
Page 75 and 76:
Custom Panel Layouts Although the p
Page 77 and 78:
LEADING ELECTRICAL DESIGN Notes 79
Page 79 and 80:
LEADING ELECTRICAL DESIGN Notes 81
show all

3 Wireless Remote Control CZone LCD QVGA ... - BUKH Bremen

Create successful ePaper yourself

Delete template?

Save as template?