LCC1653/01, LRI1653/01 - Philips Lighting

LCC1653/01, LRI1653/01
ActiLume DALI System
ActiLume DALI
15.8
Sensor LRI1653/01dimensions in mm
79.4
16.4
Controller LCC1653/01, LCC1656/00 dimensions in mm
44.7
30
22.2
Product description
The Philips ActiLume lighting control system consists of a small,
lightweight sensor and controller, designed for easy integration into
luminaires. ActiLume is a true Plug and Play solution for open plan
(up to 11 luminaires) or cell offices (e.g. 4 luminaires). It is used in
a master/slave luminaire concept, easy to use and easy to install.
Application brochures are available to help specify and apply
the system in an optimal way.
Features and benefits
• Philips ActiLume is a DALI based lighting control system designed for
maximum comfort and energy savings up to 75% (in fully automatic
mode and when used in combination with Philips HF-Regulator Touch
and DALI ballasts).
• ActiLume is a Plug & Play system; no specific lighting control training
is needed. Moreover, the system is supported with simple, dedicated
application and installation sheets.
• The ActiLume system consists out of three state-of-art miniature
sensors combined with a controller containing a series of
pre-programmed modes.
• The two most applied modes, cell and open plan offices, can be
selected via a single push on the service button.
• The light sensor is sensitive for visible radiation (matching the human
eye) providing automatic savings with daylight depending regulation,
without any visible discomfort for the user.
• The movement detector is very sensitive to human movements and
contains a 15 minutes delay to provide optimal functionality whilst
maximizing energy saving during absence.
• Personal control solutions can be created by connecting a mains
rated spring-back switch to the controller or by using an infrared
remote control unit.
• In addition ActiLume offers the possibility to select so called “comfort
modes” in line with the EN 12464 indoor lighting norm. These modes
can be recalled by using a simple mode selection tool IRT8099/20.
• If needed further customization can easily be established by changing
the factory settings with the mode selection tool IRT8099/20.
• The ActiLume controller contains two DALI outputs.These outputs
are pre-programmed (factory setting) as a window and corridor row
with a fixed light offset.
• The system can be extended with 1 or 2 additional movement
detectors, LRM8118/00 and/or LRM8119/00 to maximize movement
coverage. This respectively reduces the number of ballasts per
controller to 10 or 9.
• Factory light level setting is at 600 lux at a reflection factor of 0.3.
1/8

LCC1653/01, LRI1653/01
ActiLume DALI System
Applications
The ActiLume system is designed for all office applications, from open
plan to cell offices, lobbies or toilets, and from corridor to small meeting
rooms.
It offers dedicated modes, e.g. for schools, light-lines and direct/indirect
lighting concepts.
It even contains a specific comfort mode combining maximum energy
savings and additional comfort based on a practical EN 12464 solution
(mode 4, 5 or 9).
Plug & Play control regimes
• Mode 1: Switching light off when the area is not occupied, saving
maximum energy in a cell office situation.
• Mode 2: Maintaining a (lower) light level when the area is not
occupied, avoiding dark areas in an open plan office.
• Next to the modes the following functions can be changed
independently:
- Power up behavior
- Default light level
- Background level
Philips quality
This ensures quality with respect to:
• System supplier
• As manufacturer of lamps, electronic control gear and lighting control
equipment, Philips ensures that, from the earliest development stage,
optimum performance is maintained.
• International standards
• Philips lighting control equipment complies with all relevant
international rules and regulations.
Compliances and approvals
RFI 9kHz to 30MHz EN 55015
RFI 30MHz to 1000MHz EN 55022 A
Immunity EN 61547
Safety EN 61347-1
EN 61374-2-11
Quality standard ISO 9001
Environmental standard ISO 14001
Approval marks ENEC
CE marking
Technical data for installation
Mains operation
Rated mains voltage 220 - 240 V
Tolerances for performance -8% - +6% (202 - 254 V)
With tolerances for safety +/- 10% (198 - 264 V)
Mains frequency 50/60 Hz
Input power (system) 0.8 - 1.3 W
Number of ballasts Number of extension sensors
LRM8118/00 and/or LRM8119/00
11 0
10 1
9 2
Technical data for design and mounting in fixtures
Operating conditions
Ambient temperature 0 ºC to 55 ºC
Sensor and controller
Rel. humidity 20% to 85%,
no condensation
T case Controller 75 ºC
Sensor 55 ºC
Storage conditions
Temperature -25 ºC to +85 ºC
Rel. humidity 10% to 95% (Non condensing)
Sensor LRI1653/01
Connection RJ-10 4-Pole fixed to
LRI1653/01, 100cm cable
RJ-10 (4P4C)
Housing (casing)
Material Polycarbonate UL94V-0
Glow wire test 850 °C /5s
Safety basic insulation ≥ 1500V
When placed at a height of 3m the following values are valid:
Infrared receiver Signal range r = 2.5
Light sensor Ambient light monitoring
Monitoring 25 to 350 lux at
sensor
Monitoring area r = 2.5
2/8

LCC1653/01, LRI1653/01
ActiLume DALI System
Movement detector Passive Infra Red (PIR)
Detection area at 2.5m height: 4x4m
(sensitive for small movements)
6x5m
(sensitive for large movements)
6 m
4 m
Mounting
4 m
5 m
Large movement
detection area
Small movement
detection area
Maximum height PIR: 3.5 m
X-angle PIR: 82°
Y-angle PIR: 100°
The sensor has latching rills on the back so it can easily be mounted. It
can also be mounted onto a lamp by means of a clip LCA8002/00 or
LCA8003/00.There is an additional clip, LCA8005/00, for mounting the
sensor in the luminaire housing.
60 mm
R0-0.5 mm (4x)
1. Required Luminaires opening dimension: 60 x 22 (mm)
2. Thickness �tness of Luminaires �xture: 0.5~2.5 (mm)
22 mm
Service button
The service button can be used to:
b. Adjust the factory set reference light level.
Pressing the service button (>3 seconds) until the lamp gives a light
flash (wink) will start the automatic calibration procedure.
The light output of the luminaires connected to the window side
(DALI 1) is set to 80%.The light output of the luminaires connected
to the corridor side (DALI 2) is set to 100%.
After 30 seconds the ActiLume controller is saving the actual light
level as new reference light level (indicated by a second flash).
This 30 seconds time delay is required to have sufficient time to step
aside or remove a stepladder.
Controller unit LCC1653/01
DALI Output In user mode 1 and user mode 2 the system
is programmed as one channel. When enough
daylight enters the room, the amount of artificial
light will be automatically reduced and the DALI
2 output (corridor row) is programmed with a
light offset of 30%.
In other modes (which can be recalled with the
IRT8099/20) ActiLume can use two channels
depending the applications functionality.
Mains switch By connecting a mains rated springback switch
to connect Ls (Line-switched), dimming and
switching on/off will be possible according the
Touch and Dim functionality (Maximum 1 switch
per controller).
Switch to be connected to the controller!
Remote control It is also possible to use remote control
IRT8010/00, IRT8030/00 or IRT8050/00.The
IRT8010/00 needs to be pointed to the sensor.
The IRT8030/00 and IRT8050/00 have a X-Y-Z
beam direction, making it suitable for wall
mounting and table top use.
Glow wire test 850 ºC / 5 s
Safety, basic insulation ≥ 1500 V
Material Polycarbonate UL94 V-0
Mounting The controller housing contains snap-in pins for
quick fixation. The diameter of the fixation holes
should be maximum 4.5 mm.
The snap-in pins are designed for a metal
thickness of maximum 0.8 mm.
The distance between the fixation holes is 78 mm.
3/8
a. To select the user mode 1 and 2.
The user mode can be toggled between mode
1 and 2 by means of a short push on the service
button (

LCC1653/01, LRI1653/01
ActiLume DALI System
Connector type
Connection wiring is greatly simplified through use of WAGO 251
universal connector.
Suitable for both automatic wiring (IDC and ADS) and manual wiring.
WAGO 251 universal connector.
Wiring
DALI distribution block
Corridor = DALI 2 (Offset channel)
Corridor
Window
T&D
230VAC
DA
DA
DA
DA
Ls
Ns
N
GND
L
Mains distribution block
IDC connection
ADS/Manual connection
Release: rotate and pull
Remark: release all wires one by one
DALI distribution block
Window = DALI 1 (Master channel)
Ls DALI 1
Ns
N DALI 2
L
Sensor
Mains input connector
PCB terminal block
WAGO, series 251-104
ActiLume
Sensor
Wire cross-section
IDC connection 0.5 mm – 0.75 mm 2
including stranded wiring
ADS manual connection 0.5 mm - 1.0 mm 2
Strip length 8.0 – 9.0 mm
DA / N
DA / Ls
~
~
Master Luminaire
DALI Ballast
4/8

LCC1653/01, LRI1653/01
ActiLume DALI System
ActiLume Modes
Besides the two Plug and Play modes for cell office and open plan office,
it is possible to recall 8 other application modes as mentioned below.
This makes the ActiLume system very flexible for all different kinds of
applications.
Mode 1 - Cell of�ce
Auto on
Auto off
Mode 3 - School, classroom
Manual on
Auto off
Mode 5 - Cell of�ce
Comfort mode
EN 12464
Auto on
Auto off
Mode 7 - Toilets
Auto on
Auto off
No DLR
Mode 9 - Open plan of�ce
Always light
Auto on
Auto off
Modes
With the use of the advanced mode selection tool IRT8099/20 all
10 different modes can be selected..
Once selected, the mode can be stored and copied via a point and
shoot method.
Even when the luminaires are switched off for a longer period, stored
parameters are kept.
For more detailed information, please be referred to the Philips
ActiLume OEM Application guide
15 min.
Mode 2 - Open plan of�ce
Auto on
Auto off
15 min. 120 min.
15 min.
Mode 4 - Open plan of�ce
Comfort mode
EN 12464
15 min. 120 min.
Auto on
Auto off
15 min.
Mode 6 - Corridor
Auto on
Auto off
15 min. 60 min.
15 min. 15 min.
15 min. ∞
Mode 8 - Meeting rooms
Manual on
Auto off
Mode 10 - Open plan of�ce
Comfort mode,
always light
Auto on
Auto off
Only task
light DLR
15 min. ∞
15 min.
5/8

LCC1653/01, LRI1653/01
ActiLume DALI System
LCC1653/01 Controller
The controller from the ActiLume system.
The ActiLume system is a plug & play,
DALI-based control system which fulfills the
basic needs in offices with maximum energy
saving options by daylight harvesting and
presence detection.
LCC1656/00 Controller
Same as the LCC1653/01, but designed for
free floor standing luminaires. When the
mains is connected the light switches on
(Powerstage On).
LRI1653/01 Sensor
The multi sensor from the ActiLume
system.
IRT8098/00 Simple mode selection tool
Simple mode selection tool for ActiLume
(mode 1 and mode 2 selection). Light set
point calibrator, easy to use. Batteries are
included.
IRT8099/20 Advanced mode selection tool
Commissioning tool for OccuSwitch DALI
(OccuPlus), OccuSwitch, Saber sensors and
luminaires with ActiLume. Easy to use and
inexpensive tool to adjust the functionality,
perform an installation test and/or calibrate
light levels. The functionality is depending
on the product it is used with. Batteries are
included.
LRM8119/00 ActiLume movement
extension sensor, luminaire based
Compact luminaire based movement
detector to be used to expand the
detection area for ActiLume and
OccuSwitch DALI (OccuPlus) solutions.The
sensor is connected to the DALI line from
the controller (luminaire) and does not
require external power. Mounting height is
between 2.5 and 3.5 m.
LRM8118/00 Extension sensor
Compact movement detector to be used
to expand the detection area for ActiLume
and OccuSwitch DALI (OccuPlus) solutions.
The sensor is connected to the DALI
line from the controller (luminaire) and
does not require external power. The
sensor is suitable for both recessed and
surface mounting (in combination with the
LRH8100/00). Mounting height is between
2.5 and 3.5 m.
6/8
LRH8100/00 Surface mount adaptor
Surface mounting box for the LRM8118
extension sensor. Comes with cut-out holes
for most common cable trunking systems.
LCA8000/00 Cover ActiLume multi
sensor
Cover for the ActiLume multi sensor to
obtain the same outer dimensions as
the ActiLume MicroLuxSense and the
ActiLume 1-10V sensor.
LCA8001/00 Ring for ActiLume sensors
Ring around the cover of the ActiLume
multisensor + cover, ActiLume luminaire
based extension sensor + cover, ActiLume
1-10V sensor or ActiLume MicroLuxSense
to fit in the micro-optics of a luminaire.
LCA8002/00 ActiLume sensor clip for TL5
Clip to be used for ActiLume multisensor,
ActiLume Luminaire based extension
sensor, ActiLume 1-10V sensor and the
ActiLume MicroLuxSense .With this clip
the sensor can be directly clicked on the
TL5 lamp.
LCA8003/00 ActiLume sensor clip for
TL-D
Clip to be used for ActiLume multisensor,
ActiLume Luminaire based extension
sensor, ActiLume 1-10V sensor and the
ActiLume MicroLuxSense .With this clip
the sensor can be directly clicked on the
TL-D lamp.
LCA8004/00 Cover ActiLume extension
sensor
Cover for the ActiLume luminaire based
extension sensor to obtain the same outer
dimensions as the ActiLume MicroLuxSense
and the ActiLume 1-10V sensor.
LCA8005/00 ActiLume mounting clip for
use in luminaire.
Clip to be used for ActiLume multisensor,
ActiLume Luminaire based extension
sensor, ActiLume 1-10V sensor and the
ActiLume MicroLuxSense.With this clip the
sensor can be mounted in the luminaire
housing.

LCC1653/01, LRI1653/01
ActiLume DALI System
IRT8010/00 Hand-held two-key
transmitter
Hand-held two-key transmitter, for infrared
control of various lighting control systems.
ActiLume can also dim the lights (by
pressing a button > 0.5 sec). The unit is
supplied with batteries. A wall holder is
separately available. This transmitter is not
designed to be operated from the wall
holder. For use in all Lighting Controls
systems with IR interface excl. Dynalite.
LRH8010/00 Wall holder
Wall holder for the IRT8010/00 hand-held
two-key transmitter.
IRT8050/00 Two-key infrared remote
control
Two-key infrared remote control
transmitter for wall mounting and table-top
use. The unit can be used in combination
with ActiLume. The actual function of the
two large keys can be selected with a dip
switch in the battery compartment. A dip
switch is also used to select the group
address. Batteries are included.
7/8
IRT8030/00 Four-preset hand-held
transmitter
Four-preset hand-held transmitter, suitable
for infrared control of the ActiLume system
specifically when using Mode 8 (Meeting
room). It has 4 keys for presets and one
key for “all off”. Keys for individual control
and preset programming are located
under a hinged cover at the bottom
of the transmitter. The group address
selector switch is contained in the battery
compartment. The unit is supplied complete
with wall holder and batteries.
UID8510 IR User Interface
The UID8510 IR user interface panel
provides intuitive on/off and dimming
functionality. It connects via infrared to the
ActiLume system.
Batteries are included.

LCC1653/01, LRI1653/01
ActiLume DALI System
Packing data
Type Box dimensions Qty/ Material Weight (Kg)
(mm) Box net gross
LCC1653/01 376 x 190 x 70 48 Cardboard 0.031 1.728
LCC1656/00 376 x 190 x 70 48 Cardboard 0.031 1.728
LRI1653/01 227 x 169 x 149 48 Cardboard 0.032 1.632
LRM8118/00 80 x 72 x 40 1 Cardboard 0.076 0.083
LRH8100/00 80 x 80 x 40 1 Plastic bag 0.027 0.033
LRM8119/00 200 x 175 x 110 12 Cardboard 0.030 0.507
IRT8098/00 240 x 135 x 87 1 Cardboard 0.060 0.100
IRT8099/20 155 x 40 x 17 1 Cardboard 0.030 0.100
LCA8000/00 216 x 93 x 70 100 Cardboard 0.228 0.293
LCA8001/00 216 x 93 x 70 100 Cardboard 0.155 0.221
LCA8002/00 216 x 93 x 70 50 Cardboard 0.450 0.455
LCA8003/00 216 x 93 x 70 50 Cardboard 0.450 0.455
LCA8004/00 216 x 93 x 70 50 Cardboard 0.186 0.218
LCA8005/00 220 x 97 x 71 50 Cardboard 0.780 0.810
Ordering Data
Type MOQ Ordering number EAN code level 1 EAN code level 3 EOC
LCC1653/01 12 9137 006 13772 8711500 910424 8711500 910431 910424 30
LCC1656/00 12 9137 003 39803 8727900 921953 8727900 921960 921953 00
LRI1653/01 12 9137 006 13872 8711500 910462 8711500 910479 910462 30
LRM8118/00 1 9137 003 24703 8711559 730783 8711559 730790 730783 99
LRH8100/00 1 9137 003 18903 8711559 519203 8711559 519210 519203 99
LRM8119/00 12 9137 003 43703 8718291 139461 8718291 139478 139461 00
IRT8098/00 1 9137 003 24803 8711559 730806 8711559 730813 730806 99
IRT8099/20 1 9137 003 34203 8711559 732565 8711559 732572 732565 99
LCA8000/00 1 9137 003 38403 8727900 882803 8727900 882810 882803 00
LCA8001/00 1 9137 003 38303 8727900 882780 8727900 882797 882780 00
LCA8002/00 1 9137 003 40803 8727900 952940 8727900 952957 952940 00
LCA8003/00 1 9137 003 40903 8727900 952988 8727900 952995 952988 00
LCA8004/00 1 9137 003 43803 8718291 139386 8718291 139393 139386 00
LCA8005/00 1 9137 003 48803 8718291 196242 8718291 196259 196242 00
3222 636 35122
10/2012
Data subject to change
www.philips.com/lightingcontrols
8/8