You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
12<br />
6. Built in requirements<br />
In this chapter you will find some sketches of the outer<br />
dimensions of the components and how to mount<br />
these components. The ways of mounting given in this<br />
document are just some examples and other ways of<br />
mounting are possible.<br />
The ActiLume 1-<strong>10V</strong> Sensor has flying leads of 25.4 in.<br />
(100 cm) and is designed to be built into a luminaire. The<br />
following chapters will explain on how the sensor can be<br />
mounted into a luminaire.<br />
Furthermore the sensor should be installed above a<br />
surface where the light level is representative of the area<br />
to be monitored. The maximum installation height is 12<br />
feet (3.5 meters) from the ceiling to the floor.<br />
If the diaphragm is set to its default position (in the center),<br />
the output of the light sensor will be approximately 5V at<br />
50 footcandles on floor if the reflection factor is 0.3 (the<br />
average reflection factor of an average surface). While<br />
for other surface, the exact dimming curve is related to its<br />
reflection factor.<br />
6.1. Dimensions ActiLume 1-<strong>10V</strong> Sensor<br />
Below you will find some sketches on the most important<br />
dimensions of the Sensor.<br />
Dimensions: inches (mm)<br />
LRI1655<br />
0.08 (2)<br />
0.79 (20)<br />
0.65 (16.6)<br />
0.78 (19.8)<br />
1.73 (44)<br />
<strong>Philips</strong> ActiLume 1-<strong>10V</strong> OEM Application Guide<br />
15<br />
1 30<br />
0.74 (18.9)<br />
0.67 (17)<br />
1.84 (46.8)<br />
6.2 Mounting of the ActiLume 1-<strong>10V</strong> Sensor<br />
The sensor can be<br />
mounted into a<br />
luminaire in different<br />
ways. The following<br />
3 options are the most<br />
commonly used ways of<br />
mounting the sensor.<br />
The most simple way<br />
of mounting the sensor<br />
into the luminaire, is by using a metal clip. The clip<br />
can be mounted on the backside of the sensor and<br />
then as a composition it can be clipped onto a linear<br />
fluorescent lamp.<br />
There are 2 different clips available, one for TL-D<br />
(T8) lamps and one for TL5 (T5) lamps. The TLD<br />
version is called the LCA8002. The TL5 version of the<br />
clip is called the LCA8003. Both types can be ordered<br />
separately and are packed in boxes of 50 pieces.<br />
Please contact your local sales representative for<br />
more info on ordering these clips.<br />
Dimensions: inches (mm)<br />
0.89 (22.6)<br />
LCA8003<br />
1.51 (38.3)<br />
0.43 (11)<br />
0.18 (4.5)<br />
0.63 (16)<br />
Dimensions: inches (mm)<br />
0.89 (22.6)<br />
LCA8002<br />
1.51 (38.3)<br />
0.28 (7)<br />
0.18 (4.5)<br />
0.39 (10)<br />
0.46 (11)<br />
0.65 (16.6)<br />
1.24 (31.6)<br />
1.07 (27.1)<br />
1.37 (34.7)<br />
1.19 (30.3)
Change language