Water and Wastewater Engineering - Sciences Club

More documents

Recommendations

Info

GENERAL WASTEWATER COLLECTION AND TREATMENT DESIGN CONSIDERATIONS 18-23 4. Compare the physical characteristics of fresh sewage and septic sewage. 5. Distinguish between conventional and nonconventional pollutants. 6. State the BOD 5 , suspended solids, and fecal coliform concentrations that are often cited as a definition of secondary treatment. 7. Explain why industries are required to pretreat wastewater before discharging to municipal sewers. 8. Discuss a design strategy to address the issue of low flow at the start-up of a new wastewater treatment plant. 9. Discuss the conflicting desirability of locating the wastewater treatment plant at a low elevation and the potential soil and groundwater problems in construction at such a site. With the aid of this text, you should be able to do the following: 18-8 10. 11. Estimate the wastewater flow from commercial, institutional, and recreational facilities based on characteristic units such as occupancy, seats, guests, beds, and so on. Estimate the wastewater flow reduction that may be obtained by requiring the use of water saving devices. 12. Estimate the average daily, maximum day, peak hour, and minimum flow for domestic wastewater production. 13. Estimate the infiltration flow rate for a given area with old or new sewers. 14. Estimate the infiltration flow rate for a given length of pipe. 15. Using topographic maps, select likely locations for a wastewater treatment plant. 18-1. 18-2. PROBLEMS Estimate the average and peak hour wastewater flow rate for Camp Swampy. State all assumptions. The facility composition is shown below. a . Camp with central toilet and bath facilities—350 campers b. Staff cottages with private bath, two people per cottage—40 staff members c. Dining hall serves three meals per day to campers and staff A proposal to build Hotel California is being evaluated to estimate wastewater flow rates. Two proposals are being considered. Estimate the average and peak hour wastewater flow rate for each proposal. State all assumptions. The owner has asked two questions: (1) What is the impact on wastewater flow rate of having a bar with the restaurant? (2) With respect to wastewater flow, are there any economies of scale? The proposals are outlined in the table below. Assume an average occupancy of 80%, 1.5 people per room, and a maximum occupancy of 100%, 2 people per room.
18-24 WATER AND WASTEWATER ENGINEERING 18-3. 18-4. 18-5. 18-6. Unit Proposal A Proposal B Guest rooms 120 240 Number of employees 12 17 Self-service laundry machines 2 4 Restaurant, no bar, seats 80 120 Restaurant, with bar, seats 100 160 Repeat Problem 18-1 assuming the following water saving features are introduced: a . Low-flush toilets that reduce flow from 73 to 35 L/capita · d. b. Limiting flow shower head that reduces flow from 50 to 42 L/capita · d. c. Energy-saver dishwasher that saves 10 L/meal. Repeat Problem 18-2 assuming the following water saving features are introduced: a . Low-flush toilets that reduce flow from 73 to 35 L/capita · d. b. Limiting flow shower head that reduces flow from 50 to 42 L/capita · d. Analyze Xenia’s wastewater flow rate data to estimate the following: average daily flow rate, estimated maximum day, estimated peak hour, minimum day, and dry weather flow. Assume the dry season occurs from the beginning of May to the end of September. (Data from Metcalf & Eddy, 2003.) Xenia’s flow data, m 3 /d Year 2006 2007 Population Month 8,690 9,400 January 8,800 13,900 February 6,200 9,900 March 6,800 8,100 April 4,000 4,200 May 4,000 5,700 June 3,600 3,600 July 2,400 2,600 August 2,000 1,500 September 2,800 2,000 October 3,200 4,800 November 4,800 3,200 December 5,200 6,700 Analyze Eau Gaullie’s wastewater flow rate data to estimate the following: average daily flow rate, estimated maximum day, estimated peak hour, minimum day, and
Page 2 and 3:
List of the elements with their sym
Page 4 and 5:
WATER AND WASTEWATER ENGINEERING
Page 6 and 7:
WATER AND WASTEWATER ENGINEERING De
Page 8 and 9:
Dedication To all the professionals
Page 10 and 11:
ABOUT THE AUTHOR Mackenzie L. Davis
Page 12 and 13:
This book is designed for use by pr
Page 14 and 15:
Larry Sanford, Assistant Supervisor
Page 16 and 17:
PROFESSIONAL ADVISORY BOARD Myron E
Page 18 and 19:
Lucy B. Pugh, P. E., BCEE, Vice Pre
Page 20 and 21:
Preface 1 The Design and Constructi
Page 22 and 23:
7-10 Problems 7-40 7-11 Discussion
Page 24 and 25:
15 Water Plant Residuals Management
Page 26 and 27:
22 Wastewater Microbiology 22-1 22-
Page 28 and 29:
Appendix A A-1 Properties of Air, W
Page 30 and 31:
1-1 INTRODUCTION 1-2 PROJECT PARTIC
Page 32 and 33:
TABLE 1-1 Some observed professiona
Page 34 and 35:
In alternative approaches such as d
Page 36 and 37:
The client’s view of the project
Page 38 and 39:
eading journal articles, and partic
Page 40 and 41:
Establishment of Design Criteria. D
Page 42 and 43:
TABLE 1-3 Guidance for minimum equi
Page 44 and 45:
S ite limitations. The location and
Page 46 and 47:
In conjunction with the client, the
Page 48 and 49:
equirements because an initial assu
Page 50 and 51:
points in the construction be ident
Page 52 and 53:
documents (EJCDC, 2002). Not withst
Page 54 and 55:
1-10 1-3. 1-4. 1-1. 1-2. 1-3. The c
Page 56 and 57:
Metcalf & Eddy, Inc. (2003) Wastewa
Page 58 and 59:
2-1 WATER DEMAND 2-2 WATER SOURCE E
Page 60 and 61:
TABLE 2-1 Design periods for water
Page 62 and 63:
TABLE 2-3 Typical wastewater flow r
Page 64 and 65:
TABLE 2-5 Typical changes in water
Page 66 and 67:
Population water source Groundwater
Page 68 and 69:
2-11 TABLE 2-7 Average monthly disc
Page 70 and 71:
GENERAL WATER SUPPLY DESIGN CONSIDE
Page 72 and 73:
TABLE 2-9 Theoretical relationship
Page 74 and 75:
1995 Jan 2.89 0.1445 0.387 0.25 0.6
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
3. 4. GENERAL WATER SUPPLY DESIGN C
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
TABLE 2-13 Examples of sources to b
Page 88 and 89:
2-31 Organics Ethylbenzene 0.7 0.7
Page 90 and 91:
2-33 Microbials Cryptosporidium Zer
Page 92 and 93:
TABLE 2-16 Maximum contaminant leve
Page 94 and 95:
TABLE 2-17 Secondary maximum contam
Page 96 and 97:
Page 98 and 99:
2-41 Squannacook River near West Gr
Page 100 and 101:
2-8. GENERAL WATER SUPPLY DESIGN CO
Page 102 and 103:
a plot on probability paper. Using
Page 104 and 105:
3-1 INTRODUCTION 3-2 DESIGN ELEMENT
Page 106 and 107:
3-3 Max w.s. 4-vertical mixed flow
Page 108 and 109:
TABLE 3-2 Types of intake structure
Page 110 and 111:
Perforated pipe Perforated pipe Col
Page 112 and 113:
TABLE 3-4 Intake port design criter
Page 114 and 115:
The unit space occupied by a bar an
Page 116 and 117:
75 m diameter piping Water surface
Page 118 and 119:
Slope. To avoid air blockage, the c
Page 120 and 121:
Pump Criteria Pump Type. The most c
Page 122 and 123:
The AFD allows changes in the flow
Page 124 and 125:
v 2 d /2g Datum EGL HGL H baronetri
Page 126 and 127:
1 2 �h s �h s Datum h a FIGURE
Page 128 and 129:
Total dynamic head, m 20 19 18 17 1
Page 130 and 131:
P umps are selected from those comm
Page 132 and 133:
e. From Figure 3-16 , the maximum T
Page 134 and 135:
Slope. The gallery can be horizonta
Page 136 and 137:
Heating the water at the intake por
Page 138 and 139:
Hints from the Field. Operation and
Page 140 and 141:
3-2. 3-3. 3-4. Design a shore river
Page 142 and 143:
Elev. = 335.1 m FIGURE P-3-6 Condui
Page 144 and 145:
3-8 3-9 3-1. 3-2. (3) efficiency at
Page 146 and 147:
4-1 INTRODUCTION 4-2 DESIGN ELEMENT
Page 148 and 149:
quality standards, the strata that
Page 150 and 151:
TABLE 4-1 Typical isolation distanc
Page 152 and 153:
Pump discharge Large diameter sucti
Page 154 and 155:
Grout overflow Drilled hole diamete
Page 156 and 157:
Minimum of 4 m of water at start of
Page 158 and 159:
pressure, the vent is essential to
Page 160 and 161:
Protective casing Ventilation To wa
Page 162 and 163:
In either instance, the degree of i
Page 164 and 165:
TABLE 4 -3 (continued) Values of W(
Page 166 and 167:
Drawdown, m 0.0 1.0 2.0 3.0 4.0 t o
Page 168 and 169:
In addition, because each well is i
Page 170 and 171:
Surface of seepage h iw 2r w h w Tr
Page 172 and 173:
motor and pump are in the water in
Page 174 and 175:
located by hydraulic analysis to lo
Page 176 and 177:
Cumulative percent retained 100 90
Page 178 and 179:
Screen Diameter The selection of a
Page 180 and 181:
An analysis of the water indicates
Page 182 and 183:
3 × − ( 225 . )( 2. 818 10 m/s)(
Page 184 and 185:
The open area of the screen is The
Page 186 and 187:
NPSH A � 9.6 m 38.7 m NPSH R �
Page 188 and 189:
4-3. 4-4. 4-5. 4-6. 4-7. 4-8. 4-9.
Page 190 and 191:
N 4-19. 002 004 FIGURE P-4-18 50 m
Page 192 and 193:
2 137.5 m Plant Proposed new well 6
Page 194 and 195:
4-24. EXTRACT FROM WELL LOG Locatio
Page 196 and 197:
4-7 4-8 4-1. 4-2. 4-3. 4-4. 40.0 60
Page 198 and 199:
5-1 INTRODUCTION 5-2 REDUNDANCY AND
Page 200 and 201:
Unloading may be accomplished by pn
Page 202 and 203:
c. From Table 5-1 , an interruptibl
Page 204 and 205:
Liquified Gases. Gases are normally
Page 206 and 207:
TABLE 5-2 Dry feeder characteristic
Page 208 and 209:
5-11 5 cm schedule 80 pvc fill line
Page 210 and 211:
Chlorine gas feeder Remote from con
Page 212 and 213:
5-15 TABLE 5-5 Recommended material
Page 214 and 215:
⎛ 1 ⎞ ⎛ 1 ⎞ 3 ( 4750 , kg/d
Page 216 and 217:
5-19 Chemical (D = dry; L = liquid;
Page 218 and 219:
5-9 CHAPTER REVIEW When you have co
Page 220 and 221:
5-5. 5-6. 5-7. chlorine gas cylinde
Page 222 and 223:
5-12 REFERENCES Anderson, J. L. (20
Page 224 and 225:
6-1 INTRODUCTION 6-2 CHARACTERISTIC
Page 226 and 227:
condition the small particles for s
Page 228 and 229:
� Anode Negatively charged ion Pa
Page 230 and 231:
TABLE 6-1 Frequently used inorganic
Page 232 and 233:
As shown in Figure 6-5 b, the charg
Page 234 and 235:
Case I Acid is added to carbonate b
Page 236 and 237:
pH 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Page 238 and 239:
educed and is generally not an oper
Page 240 and 241:
Log [Fe], mol/L �2 �3 �4 �5
Page 242 and 243:
Jar test II Jar numbers 1 2 3 4 5 6
Page 244 and 245:
Example 6-4 illustrates the impact
Page 246 and 247:
Polymer. In rare instances, usually
Page 248 and 249:
The velocity gradient may be though
Page 250 and 251:
The focus of this discussion is on
Page 252 and 253:
Example 6-5. Using Table 6-4 select
Page 254 and 255:
Pressure drop per element, kPa 1000
Page 256 and 257:
i. Estimate Gt. �1 Gt �( 241. 9
Page 258 and 259:
n � rotational speed, revolutions
Page 260 and 261:
Flocculation Mixing Design Criteria
Page 262 and 263:
A B C 3 Q � 10000 m3 /d 4 0.116 m
Page 264 and 265:
n. Execute solve to find the number
Page 266 and 267:
d. Each basin is divided into three
Page 268 and 269:
TABLE 6-7 Design recommendations fo
Page 270 and 271:
�3 j. Each paddle wheel is then 6
Page 272 and 273:
Comments: 1. Because G i s tapered,
Page 274 and 275:
6-4. 6-5. 6-6. 6-7. Calculate the
Page 276 and 277:
6-14. 6-15. at 175 rpm has been shi
Page 278 and 279:
6-20. 6-21. 4. Compartment length
Page 280 and 281:
6-23. For each compartment L � W
Page 282 and 283:
Packham, R. F. (1965) “Some Studi
Page 284 and 285:
7-1 HARDNESS 7-2 LIME-SODA SOFTENIN
Page 286 and 287:
Extremely soft Very soft Soft to mo
Page 288 and 289:
discrepancy between the cation and
Page 290 and 291:
The product of the activity of the
Page 292 and 293:
4. Removal of noncarbonate hardness
Page 294 and 295:
log[Ca 2+ ] 0 -2 -4 -6 -8 -10 2 FIG
Page 296 and 297:
(a) (b) (c) CO 2 CO 2 CO 2 Ca 2�
Page 298 and 299:
Five reactions that are employed in
Page 300 and 301:
c. With p K a 1 � 6.35, solve Equ
Page 302 and 303:
179.0 mg/L as CaCO 3 � 20 mg/L as
Page 304 and 305:
21.9 CO 2 0 238 293.6 349.8 HCO 3
Page 306 and 307:
Raw water Q Mgr Aeration Lime/soda
Page 308 and 309:
emoved. Removal of the calcium equi
Page 310 and 311:
log[species] log[species] 0 �2
Page 312 and 313:
7-29 Lime Raw water CaCO 3 sludge L
Page 314 and 315:
Although rapid mixing may be provid
Page 316 and 317:
The GLUMRB design guidance is less
Page 318 and 319:
where pH is in the actual hydrogen
Page 320 and 321:
From Table 7-5 at a temperature of
Page 322 and 323:
CO 2 that is not dissolved. Exposur
Page 324 and 325:
7-6. 7-7. 7-8. 7-9. Well No. 1, Lab
Page 326 and 327:
7-13. Using K sp , show why magnesi
Page 328 and 329:
7-24. Determine the lime and soda a
Page 330 and 331:
7-12 REFERENCES AWWA (1978) Corrosi
Page 332 and 333:
8-1 INTRODUCTION 8-2 FUNDAMENTAL CO
Page 334 and 335:
Polymer chain (a) (b) � � SO
Page 336 and 337:
Properties of Ion Exchange Resins E
Page 338 and 339:
and Y j qj � q where q T � tota
Page 340 and 341:
Example 8-1. Estimate the maximum v
Page 342 and 343:
Water outlet Water inlet Meter Back
Page 344 and 345:
Column 1 Column 2 Column 3 FIGURE 8
Page 346 and 347:
The larger the laboratory or pilot
Page 348 and 349:
The column should be operated long
Page 350 and 351:
volume should be estimated in the t
Page 352 and 353:
TABLE 8-3 Typical range of design c
Page 354 and 355:
d. Compute the the area in [B17]. 3
Page 356 and 357:
8-6 CHAPTER REVIEW When you have co
Page 358 and 359:
8-3. Repeat Problem 8-2 assuming co
Page 360 and 361:
(a) C, meq/L C, meq/L (b) 12 10 8 6
Page 362 and 363:
CHAPTER 9 REVERSE OSMOSIS AND NANOF
Page 364 and 365:
Bacteria, protozoa, algae, particie
Page 366 and 367:
Flux Several models have been devel
Page 368 and 369:
Permeate water Source water & flow
Page 370 and 371:
Permeate water Concentrate outlet P
Page 372 and 373:
TABLE 9-1 Typical NF/RO membrane pr
Page 374 and 375:
d. This indicates that the solubili
Page 376 and 377:
In mg/L this is �3 ( 2. 58 �10
Page 378 and 379:
Solution: a. The saturation value o
Page 380 and 381:
9-7 15. Design a membrane array to
Page 382 and 383:
Masters, G. M. (1998) Introduction
Page 384 and 385:
10-1 INTRODUCTION 10-2 SEDIMENTATIO
Page 386 and 387:
g � acceleration due to gravity,
Page 388 and 389:
Newton’s coefficient of drag, C D
Page 390 and 391:
A B C D E F G 3 Input data 4 5 Diam
Page 392 and 393:
In the upflow clarifier, particle-l
Page 394 and 395:
50% 50% v 0 /2 perspective, this im
Page 396 and 397:
Depth, m 0.0 0.5 1.0 1.5 2.0 0 41 5
Page 398 and 399:
Suspended solids removal, % 80 70 6
Page 400 and 401:
about 60 � . The configurations a
Page 402 and 403:
For cocurrent settling, the settlin
Page 404 and 405:
TABLE 10-1 Alternative settling tan
Page 406 and 407:
24 m max Influent channel 0.05L to
Page 408 and 409:
second stage. These flocculate with
Page 410 and 411:
Recommended values for the settling
Page 412 and 413:
Horizontal-Flow Rectangular Sedimen
Page 414 and 415:
If the sludge zone is not counted,
Page 416 and 417:
TABLE 10-5 Typical design criteria
Page 418 and 419:
Operation and Maintenance. To facil
Page 420 and 421:
f. Check the approach velocity. v a
Page 422 and 423:
• Use lower mixer speed (80 to 85
Page 424 and 425:
10-14. 10-15. 10-16. Depths, a Time
Page 426 and 427:
10-19. W idth of each tank Length o
Page 428 and 429:
11-1 INTRODUCTION 11-2 AN OVERVIEW
Page 430 and 431:
conventional depth filter. The bott
Page 432 and 433:
In the mid-1980s, deep-bed, monomed
Page 434 and 435:
TABLE 11-1 Typical properties of fi
Page 436 and 437:
11-4 GRANULAR FILTRATION THEORY Mec
Page 438 and 439:
Depth, m 0.0 0.2 0.4 0.6 0.8 1.0 0.
Page 440 and 441:
TABLE 11-2 Formulas used to compute
Page 442 and 443:
Solution. The computations are show
Page 444 and 445:
where v b is the backwash velocity
Page 446 and 447:
The expanded bed porosity (next to
Page 448 and 449:
design when the raw water is improp
Page 450 and 451:
Example 11-5. In continuing the des
Page 452 and 453:
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Page 454 and 455:
(a) (b) (c) Intel main Wash water o
Page 456 and 457:
Backwash rate, m/min 2 1.8 1.6 1.4
Page 458 and 459:
“Y”, cm 50 45 40 35 30 25 20 15
Page 460 and 461:
e. The volume of backwash water for
Page 462 and 463:
e. Check depth using height of back
Page 464 and 465:
Influent Effluent 2 where v 1 , v 2
Page 466 and 467:
In addition to providing for a mini
Page 468 and 469:
TABLE 11-8 Design criteria for sing
Page 470 and 471:
TABLE 11-10 Design criteria for tri
Page 472 and 473:
TABLE 11-13 Approximate flow veloci
Page 474 and 475:
With the use of this text, you shou
Page 476 and 477:
11-9. 11-10. b. Anthracite coal E
Page 478 and 479:
11-15. 11-16. 11-17. What effect do
Page 480 and 481:
G ullet dimensions B a ckwash water
Page 482 and 483:
11-3. 11-4. Explain what air bindin
Page 484 and 485:
12-1 INTRODUCTION 12-2 MEMBRANE FIL
Page 486 and 487:
Operating pressures (kPa) Size (mic
Page 488 and 489:
Ferry (1936) developed a model for
Page 490 and 491:
Transmembrane flux Transmembrane pr
Page 492 and 493:
Pore sealing with superposition (in
Page 494 and 495:
TABLE 12-4 Comparison of hollow-fib
Page 496 and 497:
12-4 MF AND UF PRACTICE Process Des
Page 498 and 499:
Process Design Membrane Process Sel
Page 500 and 501:
Example 12-2. Determine the number
Page 502 and 503:
• Prudent design suggests install
Page 504 and 505:
12-8. 12-9. Determine the number of
Page 506 and 507:
13-1 INTRODUCTION 13-2 DISINFECTION
Page 508 and 509:
Chlorine existing in the form of HO
Page 510 and 511:
The distribution of the reaction pr
Page 512 and 513:
Example 13-2. Estimate the percent
Page 514 and 515:
Chlorine dioxide and ozone can oxid
Page 516 and 517:
The transformed data are ⎛ 1 1
Page 518 and 519:
Chlorine. The chlorine must penetra
Page 520 and 521:
Example 13-4. The data for HOCl dis
Page 522 and 523:
Time, min 1000 100 10 Hom-Haas Mode
Page 524 and 525:
Regulatory Context. Selection of an
Page 526 and 527:
Water that spends a long time in th
Page 528 and 529:
Iron, manganese, and sulfides exert
Page 530 and 531:
Weight Percent Chlorine. Chlorine i
Page 532 and 533:
it is delivered at a pH of about 12
Page 534 and 535:
The American Water Works Associatio
Page 536 and 537:
(a) (b) (c) Plan Section Rectangula
Page 538 and 539:
. From the definition of hydraulic
Page 540 and 541:
solution is 40 mg/L (U.S. EPA, 1986
Page 542 and 543:
TABLE 13-9 Log-removal/inactivation
Page 544 and 545:
a n d if the ozone concentration re
Page 546 and 547:
Multiple Contact Reactors. When seq
Page 548 and 549:
• AWWA Standard B702 for sodium f
Page 550 and 551:
Pump suction line Overflow line Mix
Page 552 and 553:
• Corrective action drills and ma
Page 554 and 555:
13-9. Because of high TOC in the ra
Page 556 and 557:
13-15. by ion exchange. The time fo
Page 558 and 559:
13-21. The town of Wallowa has aske
Page 560 and 561:
13-26. Determine the chemical feed
Page 562 and 563:
LaGrega, M. D., P. L. Buckingham, a
Page 564 and 565:
REMOVAL OF SPECIFIC CONSTITUENTS 14
Page 566 and 567:
The oxidation-reduction reaction wi
Page 568 and 569:
Comment. According to Ghurye and Cl
Page 570 and 571:
SO 4 2� � 50 mg/L NO 3 � �
Page 572 and 573:
14-9 TABLE 14-2 Arsenic treatment t
Page 574 and 575:
TABLE 14-3 Typical sorption treatme
Page 576 and 577:
2MnSO4 �2Ca( HCO3) 2�O2 → 2Mn
Page 578 and 579:
NF Yes Start Is No water aerobic ?
Page 580 and 581:
Treatment Strategies The primary me
Page 582 and 583:
In each of these instances, the reg
Page 584 and 585:
(Drewes et al., 2005; Nghiem et al.
Page 586 and 587:
Liquid in Shell Random packing Gas
Page 588 and 589:
G 2 0.1 m Fp � rg (rw -rg ) 0.4 0
Page 590 and 591:
Raw water TCE � 72.0 � g/L Te m
Page 592 and 593:
3. A spreadsheet was used to perfor
Page 594 and 595:
Solution: a. From the Freundlich eq
Page 596 and 597:
TABLE 14-10 Guide to selection of G
Page 598 and 599:
Geosmin concentration ng/L 140 120
Page 600 and 601:
16. Evaluate a preliminary design o
Page 602 and 603:
14-10. 14-11. 14-12. Packing � 90
Page 604 and 605:
Djebbar, Y. and R. M. Narbaitz (199
Page 606 and 607:
U.S. EPA (2005) A Regulator’s Gui
Page 608 and 609:
WATER PLANT RESIDUALS MANAGEMENT 15
Page 610 and 611:
TABLE 15-1 Major water treatment pl
Page 612 and 613:
Volume Reduction Relationships In t
Page 614 and 615:
Thus, on a theoretical basis, each
Page 616 and 617:
solution, 1.5 to 2 mg/L of sludge i
Page 618 and 619:
Solution. The mass balance diagram
Page 620 and 621:
5. Sludge lagoon overflow. 6. Dewat
Page 622 and 623:
the Mg(OH) 2 . The carbonated sludg
Page 624 and 625:
Influent pipe FIGURE 15-2 Continuou
Page 626 and 627:
Solids flux, kg/d·m 2 1,200 1,000
Page 628 and 629:
the supernatant must be returned to
Page 630 and 631:
. Estimate the height of the thicke
Page 632 and 633:
Lagoon Design. The required area an
Page 634 and 635:
Solids dewatered Coagulant 7 to 10%
Page 636 and 637:
The filtrate from the sand drying b
Page 638 and 639:
L � ( Di)( Psinitial )( �) A M
Page 640 and 641:
c. The data in column 5 is a conver
Page 642 and 643:
is low as shown in this example. A
Page 644 and 645:
TABLE 15-8 Typical selection of cen
Page 646 and 647:
of rotary drum vacuum filters are u
Page 648 and 649:
Follower Back-up plate Polypropylen
Page 650 and 651:
Example 15-8. A lime softening wate
Page 652 and 653:
Surface discharge (as permitted) Tr
Page 654 and 655:
No pretreatment - Disposable AA - F
Page 656 and 657:
Direct discharge to river Inject be
Page 658 and 659:
Commercial producers of topsoil use
Page 660 and 661:
15-4. If the mass of dry solids in
Page 662 and 663:
15-18. The reject from the MF membr
Page 664 and 665:
15-25. 15-26. 15-27. 15-28. 15-29.
Page 666 and 667:
Kawamura, S. (2000) Integrated Desi
Page 668 and 669:
DRINKING WATER PLANT PROCESS SELECT
Page 670 and 671:
Page 672 and 673:
Contaminant categories Reverse osmo
Page 674 and 675:
Contaminant categories Processes Re
Page 676 and 677:
Page 678 and 679:
Collector well DRINKING WATER PLANT
Page 680 and 681:
Page 682 and 683:
Page 684 and 685:
16-17 Reservoir FIGURE 16-6 E xampl
Page 686 and 687:
Page 688 and 689:
Page 690 and 691:
Page 692 and 693:
Page 694 and 695:
Page 696 and 697:
Influent value (automatic process)
Page 698 and 699:
Page 700 and 701:
16-33 Checklist Asset categorizatio
Page 702 and 703:
TABLE 16-10 Water system—layered
Page 704 and 705:
Feedwater from wells 42,000 m 3 /d
Page 706 and 707:
Mississippi River FIGURE P-16-4 MWW
Page 708 and 709:
16-9. 16-10. DRINKING WATER PLANT P
Page 710 and 711:
16-11. Primary recovery trains Reje
Page 712 and 713:
B A Lagoon system Racoon River Cont
Page 714 and 715:
16-7 16-8 16-1. 16-2. 16-3. 16-4. 1
Page 716 and 717:
17-1 INTRODUCTION 17-2 DEMAND ESTIM
Page 718 and 719:
the additional requirement of provi
Page 720 and 721:
In designing the water system, the
Page 722 and 723:
TABLE 17-4 Needed fire flow (NFF) f
Page 724 and 725:
c. The peak hour demand is then est
Page 726 and 727:
Pipe Material Selection Standards a
Page 728 and 729:
where p 1 , p 2 � pressure at poi
Page 730 and 731:
Solution: a. The hydraulic analysis
Page 732 and 733:
Four basic closure methods are used
Page 734 and 735:
Spring Pressure relief FIGURE 17-5
Page 736 and 737:
1. Run of standard tee 2. Run of te
Page 738 and 739:
Pressure control, high and low pres
Page 740 and 741: Pump station (a) Pump station (b) P
Page 742 and 743: TABLE 17-9 Required duration for fi
Page 744 and 745: Riser Pipe. This pipe is connected
Page 746 and 747: Side view Side view Top view Top vi
Page 748 and 749: FIGURE 17-14 Horizontal pump with a
Page 750 and 751: TABLE 17-10 Typical minor loss fact
Page 752 and 753: increased reliability of service an
Page 754 and 755: Sanitary Protection of Water Mains
Page 756 and 757: 17. On a pipe network, locate the p
Page 758 and 759: 17-8. 17-9. 17-10. 100 mm 100 mm 10
Page 760 and 761: 17-16. 17-17. 17-18. 17-19. 17-20.
Page 762 and 763: 17-24. 17-25. g. System pressure is
Page 764 and 765: 128 m 120 m N Bacon Road 120 m FIGU
Page 766 and 767: 17-3. 17-12 You have been asked to
Page 768 and 769: GENERAL WASTEWATER COLLECTION AND T
Page 772 and 773: TABLE 18-2 Principal flow rate term
Page 776 and 777: TABLE 18-5 Typical composition of u
Page 782 and 783: Final Use or Disposal Practice LAND
Page 788 and 789: TABLE 18-17 Summary of requirements
Page 792 and 793: 18-7. 18-8. 18-9. 18-10. GENERAL WA
Page 794 and 795: 128 18-12. 120 120 128 MLD 1 MAR 20
Page 796 and 797: 19-1 INTRODUCTION 19-2 PREDESIGN AC
Page 798 and 799: Street Main Wye Connection to main
Page 800 and 801: Spigot FIGURE 19-3 Nomenclature of
Page 802 and 803: Elevation HHA (Start pumps & sound
Page 804 and 805: Because the sewer is under pressure
Page 806 and 807: The pipe is manufactured with integ
Page 808 and 809: Slope. All sewers shall be designed
Page 810 and 811: • A drop manhole may be used to m
Page 812 and 813: TABLE 19-5 Typical values of n that
Page 814 and 815: Note that cos 1/2 q � 1 � 2 d /
Page 816 and 817: 4 Increase slope Start Compute flow
Page 818 and 819: and 14.5 L/s, respectively. Infiltr
Page 820 and 821: Q full, m 3 /s Q/Q full v/v full j.
Page 822 and 823: w. Column 10, line 3: The slope of
Page 824 and 825: Drop manhole 150 mm water main FIGU
Page 826 and 827: piping system should be designed ba
Page 828 and 829: and the size of solid that can pass
Page 830 and 831: The ground floor must be set above
Page 832 and 833: TABLE 19-8 Submergence depth requir
Page 834 and 835: station is located at a low point,
Page 836 and 837: TABLE 19-9 Personal protective equi
Page 838 and 839: 19-3. 19-4. Write an equation that
Page 840 and 841:
an inverted siphon that will carry
Page 842 and 843:
20.82 Harrison Ave. 19.96 19.55 19.
Page 844 and 845:
Peters, J., E. G. Malter, and B. Sc
Page 846 and 847:
HEADWORKS AND PRELIMINARY TREATMENT
Page 848 and 849:
TABLE 20-1 Typical screw pump selec
Page 850 and 851:
h. To meet the redundancy requireme
Page 852 and 853:
c 40 35 30 25 20 15 10 5 0 0.01 FIG
Page 854 and 855:
(a) 5 pipe diameters (b) Magnet coi
Page 856 and 857:
Deck Deck (a) (c) Continous chain s
Page 858 and 859:
Location. In nearly all cases, scre
Page 860 and 861:
(a) (b) A B C D E 4 Average Q 5 n
Page 862 and 863:
Page 864 and 865:
5. Differential headloss for activa
Page 866 and 867:
2. Sensors for headloss should have
Page 868 and 869:
Page 870 and 871:
Grinders Grinders pulverize the sol
Page 872 and 873:
Cumulative percent passing 100 90 8
Page 874 and 875:
ate of velocity of the roll. The pa
Page 876 and 877:
ulb shape to provide this geometry
Page 878 and 879:
TABLE 20-11 Typical design criteria
Page 880 and 881:
. Using the peak hour flow rate fro
Page 882 and 883:
Wastewater flow Average daily flow
Page 884 and 885:
Example 20-6. Determine the equaliz
Page 886 and 887:
h. The mass of BOD 5 entering the e
Page 888 and 889:
The basins may also be made out of
Page 890 and 891:
f. Assume each aerator is placed in
Page 892 and 893:
Visit the text website at www.mhpro
Page 894 and 895:
Page 896 and 897:
20-20. 20-21. 20-22. 20-23. 20-24.
Page 898 and 899:
Parshall, R. L. (1926a) Bulletin 33
Page 900 and 901:
21-1 INTRODUCTION 21-2 SEDIMENTATIO
Page 902 and 903:
number of particles decreases with
Page 904 and 905:
Scum trough Scum pit Scum pipe Brid
Page 906 and 907:
or by sizing of the primary clarifi
Page 908 and 909:
If the hydraulic gradient is such t
Page 910 and 911:
c. The elevation of the bottom of t
Page 912 and 913:
Solution: a. Note that the clarifie
Page 914 and 915:
The feedwell can promote flocculati
Page 916 and 917:
Circular baffle Influent FIGURE 21-
Page 918 and 919:
d. After another iteration, the fee
Page 920 and 921:
are too low, the orifice may not be
Page 922 and 923:
A single sludge hopper with a cross
Page 924 and 925:
Hose bibs should be provided at eac
Page 926 and 927:
4. Discuss the proposed design phil
Page 928 and 929:
21-12. Design a splitting box for t
Page 930 and 931:
U.S. EPA (1975) Process Design Manu
Page 932 and 933:
22-1 INTRODUCTION 22 -2 ROLE OF MIC
Page 934 and 935:
Obligate anaerobes are microorganis
Page 936 and 937:
1 O2�2H �2e H2O 2 � � ⇌ 1
Page 938 and 939:
HO H : O : H HO H + HO H HS R CH 2
Page 940 and 941:
NADH Flavoprotein Quinone Cytochrom
Page 942 and 943:
Bacterial numbers 10 6 10 5 10 4 10
Page 944 and 945:
FIGURE 22-9 Population dynamics in
Page 946 and 947:
E q uations 22-16 and 22-19 are a f
Page 948 and 949:
The microbiology, stoichiometry, gr
Page 950 and 951:
The � nm values for nitrifying or
Page 952 and 953:
Growth Kinetics. The substrate util
Page 954 and 955:
TABLE 22-2 Volatile fatty acids and
Page 956 and 957:
pH, low nitrogen, low oxygen, and h
Page 958 and 959:
22 -3. 22 -4. 22-5. 22-6. 22 -7. De
Page 960 and 961:
Monod, J. (1949) “The Growth of B
Page 962 and 963:
SECONDARY TREATMENT BY SUSPENDED GR
Page 964 and 965:
Page 966 and 967:
TABLE 23-1 Selected activated sludg
Page 968 and 969:
DO uptake (mg ⁄ L·d) Substrate (
Page 970 and 971:
Preanoxic Influent Postanoxic Anoxi
Page 972 and 973:
Influent Influent Anaerobic Aerobic
Page 974 and 975:
(a) (b) Air Influent Air Influent B
Page 976 and 977:
Aeration tank (Q + Qr ) Q, S0 , X0
Page 978 and 979:
Page 980 and 981:
Page 982 and 983:
Page 984 and 985:
Page 986 and 987:
Using Equation 23-12 , this may be
Page 988 and 989:
j. Add the following constraint in
Page 990 and 991:
where NO x � concentration of NH
Page 992 and 993:
. Estimate the mass of O 2 as �3
Page 994 and 995:
TABLE 23-6 Typical clean water oxyg
Page 996 and 997:
h. The required air flow rate is fo
Page 998 and 999:
SDNR, g NO 3 -N/g biomass . d 0.4 0
Page 1000 and 1001:
Page 1002 and 1003:
Page 1004 and 1005:
TABLE 23-10 U.S. EPA’s recommende
Page 1006 and 1007:
Minimum 1.2 m Dia precast manhole s
Page 1008 and 1009:
. For three cells of equal size, th
Page 1010 and 1011:
Grit chamber Raw sewage pumps Wet w
Page 1012 and 1013:
Effluent NH 4 �N concentrtion, mg
Page 1014 and 1015:
2 W Influent Rotor 6m L Brush rotor
Page 1016 and 1017:
Page 1018 and 1019:
j. As in step (g), estimate � nit
Page 1020 and 1021:
Page 1022 and 1023:
c. The cross-sectional area of the
Page 1024 and 1025:
Page 1026 and 1027:
A suggested design approach is as f
Page 1028 and 1029:
Page 1030 and 1031:
Recognizing that V F � V S = V T
Page 1032 and 1033:
Page 1034 and 1035:
At a fill time of 2.25 h 1233 , , 4
Page 1036 and 1037:
Page 1038 and 1039:
TABLE 23-17 BOD/P and COD/P ratios
Page 1040 and 1041:
Page 1042 and 1043:
Page 1044 and 1045:
Page 1046 and 1047:
Page 1048 and 1049:
Page 1050 and 1051:
Page 1052 and 1053:
Page 1054 and 1055:
Page 1056 and 1057:
Page 1058 and 1059:
Return Activated Sludge (RAS) RAS r
Page 1060 and 1061:
Page 1062 and 1063:
23-12. 23-13. 23-14. SECONDARY TREA
Page 1064 and 1065:
Page 1066 and 1067:
Page 1068 and 1069:
23-46. SECONDARY TREATMENT BY SUSPE
Page 1070 and 1071:
Page 1072 and 1073:
23-7. Influent Q SECONDARY TREATMEN
Page 1074 and 1075:
23-12 REFERENCES SECONDARY TREATMEN
Page 1076 and 1077:
Page 1078 and 1079:
SECONDARY TREATMENT BY ATTACHED GRO
Page 1080 and 1081:
( a ) ( b ) SECONDARY TREATMENT BY
Page 1082 and 1083:
z z � dz L 0 SECONDARY TREATMENT
Page 1084 and 1085:
Page 1086 and 1087:
Page 1088 and 1089:
Page 1090 and 1091:
Inlet from primary Raw wastewater D
Page 1092 and 1093:
Page 1094 and 1095:
Page 1096 and 1097:
25 -1 INTRODUCTION 25 -2 SECONDARY
Page 1098 and 1099:
Solids flux, kg/m 2 � h 10 8 6 4
Page 1100 and 1101:
Suspended solids concentration, kg/
Page 1102 and 1103:
SECONDARY SETTLING, DISINFECTION, A
Page 1104 and 1105:
d. The clarifier overflow rate (OFR
Page 1106 and 1107:
TABLE 25-4 Secondary clarifier over
Page 1108 and 1109:
TABLE 25-5 Ranges of loading rate f
Page 1110 and 1111:
Page 1112 and 1113:
TABLE 25-7 Typical chlorine dosages
Page 1114 and 1115:
Page 1116 and 1117:
Page 1118 and 1119:
With the aid of this text, you shou
Page 1120 and 1121:
25 -4. 25 -5. SECONDARY SETTLING, D
Page 1122 and 1123:
26-1 INTRODUCTION 26-2 CHEMICAL PRE
Page 1124 and 1125:
The removal of phosphorus to preven
Page 1126 and 1127:
Hints from the Field. Experience fr
Page 1128 and 1129:
Sand on bottom Effective size Unifo
Page 1130 and 1131:
Denitrification Filters. Coarse-med
Page 1132 and 1133:
TABLE 26-7 Typical filtrate water q
Page 1134 and 1135:
Carbon Selection The critical eleme
Page 1136 and 1137:
Visit the text website at www.mhpro
Page 1138 and 1139:
26-6. 26-7. A dual media denitrific
Page 1140 and 1141:
WASTEWATER PLANT RESIDUALS MANAGEME
Page 1142 and 1143:
Page 1144 and 1145:
TABLE 27-1 Typical design propertie
Page 1146 and 1147:
M N Supernatant P Filtrate Degritte
Page 1148 and 1149:
TABLE 27-2 Mass balance equations f
Page 1150 and 1151:
TABLE 27-3 Mass balance equations f
Page 1152 and 1153:
TABLE 27-5 Advantages and disadvant
Page 1154 and 1155:
Multiplication factor, K 14 12 10 8
Page 1156 and 1157:
This is less than 1.5 m/s so the pi
Page 1158 and 1159:
TABLE 27-6 Occurrence of thickening
Page 1160 and 1161:
Air bubble formation WASTEWATER PLA
Page 1162 and 1163:
Page 1164 and 1165:
TABLE 27-9 Example lime dosages for
Page 1166 and 1167:
Ms Vsl � ( �)( Ssl )( Ps) 3 Ms
Page 1168 and 1169:
Page 1170 and 1171:
TABLE 27-11 Characteristics of supe
Page 1172 and 1173:
3 3 3 270 m /d[ 38, 000 g/m �( 0.
Page 1174 and 1175:
Stage 1: Hydrolysis and fermentatio
Page 1176 and 1177:
c. Solve the mass balance for COD .
Page 1178 and 1179:
Page 1180 and 1181:
With a safety factor of 5, the esti
Page 1182 and 1183:
The remainder of the discussion on
Page 1184 and 1185:
Page 1186 and 1187:
Page 1188 and 1189:
c. Compute the heat loss by conduct
Page 1190 and 1191:
CO 2 in digester gas, % 50 40 30 20
Page 1192 and 1193:
Page 1194 and 1195:
Page 1196 and 1197:
Hydraulic: Solids loading: 3 10. 7
Page 1198 and 1199:
Page 1200 and 1201:
2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Des
Page 1202 and 1203:
Page 1204 and 1205:
Page 1206 and 1207:
27-26. 27-27. 27-28. 27-29. 25 mm i
Page 1208 and 1209:
Task Committee (1988) “Belt Filte
Page 1210 and 1211:
CLEAN WATER PLANT PROCESS SELECTION
Page 1212 and 1213:
9. It is essential that residuals m
Page 1214 and 1215:
TABLE 28-1 (continued) Important fa
Page 1216 and 1217:
Page 1218 and 1219:
28-9 TABLE 28-6 Conceptual process
Page 1220 and 1221:
TABLE 28-7 (continued) Process Adva
Page 1222 and 1223:
TABLE 28-8 (continued) Process Adva
Page 1224 and 1225:
Page 1226 and 1227:
TABLE 28-13 Advantages and disadvan
Page 1228 and 1229:
TABLE 28-14 (continued) Process Adv
Page 1230 and 1231:
Inffluent Carbon source Anoxic 0.5-
Page 1232 and 1233:
Page 1234 and 1235:
Page 1236 and 1237:
Page 1238 and 1239:
Bioreactor distribution channel 27.
Page 1240 and 1241:
Page 1242 and 1243:
28-33 TABLE 28-18 (continued) Unit
Page 1244 and 1245:
Elevation, m 26 24 22 20 18 16 Maxi
Page 1246 and 1247:
TABLE A-1 Physical properties of wa
Page 1248 and 1249:
TABLE A-3 Properties of saturated w
Page 1250 and 1251:
TABLE A-7 Properties of air at stan
Page 1252 and 1253:
TABLE A-9 Properties of selected or
Page 1254 and 1255:
A-9 TABLE A-11 Characteristics of c
Page 1256 and 1257:
U.S. sieve designation Size of open
Page 1258 and 1259:
TABLE C-1 Hazen-Williams friction c
Page 1260 and 1261:
C-3 TABLE C-4 SI-based velocity and
Page 1262 and 1263:
C-5 TABLE C-4 (continued) SI-based
Page 1264 and 1265:
C-7 TABLE C-5 (continued) Hydraulic
Page 1266 and 1267:
APPENDIX D U.S. ENVIRONMENTAL PROTE
Page 1268 and 1269:
TABLE D-1 (continued) Ct values (mg
Page 1270 and 1271:
Page 1272 and 1273:
Page 1274 and 1275:
TABLE D-10 Ct values (mg · min/L)
Page 1276 and 1277:
A/O, 23-10, 23-11 A 2 /O, 23-11, 23
Page 1278 and 1279:
Beta (β) factor in aeration, 23-32
Page 1280 and 1281:
Concentrate, RO/NF, 9-9 Conceptual
Page 1282 and 1283:
Dissociation: table of constants, A
Page 1284 and 1285:
Freundlich equation, 14-29 Froude n
Page 1286 and 1287:
esins, 8-2 backbone, 8-2, 8-3 matri
Page 1288 and 1289:
Microfiltration (MF) and ultrafiltr
Page 1290 and 1291:
Pathogens, in drinking water, 2-25,
Page 1292 and 1293:
Radium-226, removal of, 14-21 Radon
Page 1294 and 1295:
Settling velocity, 10-3-10-7 and So
Page 1296 and 1297:
levels, 17-26 location, 17-23-17-25
Page 1298 and 1299:
stabilization, 28-18 thickening, 28
Page 1300 and 1301:
Useful conversion factors Multiply
show all

Water and Wastewater Engineering - Sciences Club

Create successful ePaper yourself

Delete template?

Save as template?