Specialty Automotive Hand Tools – SP Tools Schley Products
Specialty Automotive Hand Tools – SP Tools Schley Products
Specialty Automotive Hand Tools – SP Tools Schley Products
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
••••••••UNIVERSAL TOOLS••••••••<br />
Individual Part Numbers<br />
Part# Size Part# Size<br />
89930 3mm 90310 3/32"<br />
89940 4mm 90320 1/8"<br />
89950 5mm 90330 3/16"<br />
90340 1/4"<br />
7 <strong>SP</strong> TOOLS / SCHLEY PRODUCTS INC.<br />
ROLL PIN INSTALLING TOOLS<br />
The tip of each tool has a precision machined cavity which holds the roll pin due to a slight press fit.<br />
In operation, the roll pin is easily installed as the tool holds it in place up to the hole it is going into.<br />
The roll pin is then pressed in as the tool is struck with a hammer. The tool’s grip on the roll pin is then<br />
released as the roll pin goes into place. Each set comes in its own rugged, industrial tool pouch for easy<br />
identification and storage.<br />
UNIVERSAL VALVE ADJUSTMENT TOOLS<br />
For Use On All 10mm, 12mm, 13mm Jam Nut Adjustment Screws<br />
This Universal Valve Adjustment Tool has been designed for a wide variety of cars with<br />
10mm, 12mm & 13mm jam nut valve adjustment screws. This two in one tool features<br />
a window in its socket so the technician can see the position of the screwdriver blade<br />
holding the adjustment screw as the jam nut is tightened. The unique handle pivots from<br />
one side to the other, so the window is always visible. Made from heat treated chrome<br />
vanadium steel this tool comes with a soft grip handle.<br />
Part Number 88800 12mm<br />
88900 13mm<br />
88950 10mm<br />
HUB BEARING REMOVERS<br />
These unique tools were designed to remove the hub bearings that are rusted to the<br />
steering knuckle, without removing the steering knuckle from the vehicle or the CV axle<br />
assembly, also when utilized properly does not require the use of a press. Available<br />
are two sizes which fit any hub bearing with 12 mm X 1.75 or 14 mm X 1.5 thread.<br />
Simple in design and effective in use, these hub bearing removers will save an hour +<br />
when removing stubborn hub bearings.<br />
The 12 mm works on many:<br />
Chrysler, GM, Ford, Mazda, Saturn, Volvo, Isuzu, Saab and other vehicles with 12 mm<br />
X 1.75 thread.<br />
The 14 mm works on many:<br />
Chrysler, GM, Ford, Honda, Nissan, Infinity, VW, Audi, Mazda, Volvo, Mitsubishi, Kia,<br />
Hummer, and other vehicles with 14 mm X 1.5 tread.<br />
• Saves 1 hour + on stubborn hub bearing removal.<br />
• No press required<br />
• Fits any hub bearing with M12 X 1.75 or M14 X 1.5 threads<br />
• Each tool has a hex on the shaft to help install or remove the Hub Bearing Remover<br />
UNIVERSAL OHC VALVE <strong>SP</strong>RING COMPRESSOR<br />
With this latest evolution to our Universal Valve Spring Tool we have added the ability to actuate the compression tube even<br />
in tight confined locations like under the cowl where the lever cannot be moved or may not even fit. By adding the ability to<br />
separate the lever from the compression tube anywhere along the bar you can compress the springs that are confined by brake<br />
boosters, AC housings or other factors by locating the lever along the bar where there is open space.<br />
Part Number 91400B<br />
PATENT<br />
PENDING<br />
Part Number 90300<br />
Inch set of 3/32, 1/8,<br />
3/16 & 1/4 inch.<br />
Part Number<br />
69610 12 mm<br />
69630 14 mm<br />
Part Number 91410B<br />
UPDATE KIT<br />
Updates #91400A to #91400B<br />
The update kit includes: Hex bar, two hex slider blocks,<br />
three detent clevis pins and a short lever bar,.