- Page 1: Engineering Guide
- Page 5 and 6: 6. Electrical Data Electrical Formu
- Page 7 and 8: Flows in these tables are based on
- Page 9 and 10: CAPACITY, CFH @ 1″ W.C. PRESSURE
- Page 11 and 12: These tables list compressible flow
- Page 13 and 14: CAPACITY, SCFH @ 10 PSI PRESSURE DR
- Page 15 and 16: PIPING PRESSURE LOSSES FOR LOW PRES
- Page 17 and 18: SIMPLIFIED SELECTION OF AIR, GAS AN
- Page 19 and 20: The total pressure of an air stream
- Page 21 and 22: 1.Effect of Blower Speed on Flow, P
- Page 23 and 24: Absolute Specific Temp. Temp. Densi
- Page 25 and 26: COMBUSTION PROPERTIES OF COMMERCIAL
- Page 27 and 28: CHAPTER 4 - OIL FUEL OIL SPECIFICAT
- Page 29 and 30: Specific Gravity @ 60°F 1.1 1.0 0.
- Page 31 and 32: OIL PIPING TEMPERATURE LOSSES This
- Page 33 and 34: 1000's of Btu/hr Burner Input Requi
- Page 35 and 36: CHAPTER 6 - ELECRICAL DATA ELECTRIC
- Page 37 and 38: CHAPTER 7 - PROCESS HEATING HEAT BA
- Page 39 and 40: THERMAL PROPERTIES OF VARIOUS MATER
- Page 41 and 42: THERMAL PROPERTIES OF VARIOUS MATER
- Page 43 and 44: INDUSTRIAL HEATING OPERATIONS-TEMPE
- Page 45 and 46: B A CRUCIBLES FOR METAL MELTING - D
- Page 47 and 48: Btu/Hr Required Per SCFM of Process
- Page 49 and 50: LIQUID HEATING - BURNER SIZING GUID
- Page 51 and 52: Heat Transfer Rate, Btu/Sq Ft x 100
- Page 53 and 54:
CHAPTER 8 - COMBUSTION DATA AVAILAB
- Page 55 and 56:
Furnacr Thermal Head or Draft, "wc
- Page 57 and 58:
B A A 90° Elbow B DIMENSIONS OF MA
- Page 59 and 60:
CIRCUMFERENCES AND AREAS OF CIRCLES
- Page 61 and 62:
DRILL SIZE DATA Twist Dia. Area Twi
- Page 63 and 64:
CHAPTER 10 - ABBREVIATIONS & SYMBOL
- Page 65 and 66:
ELECTRICAL SYMBOLS (Cont’d) Descr
- Page 67 and 68:
GENERAL CONVERSION FACTORS (Cont’
- Page 69 and 70:
GENERAL CONVERSION FACTORS (Cont’
- Page 71 and 72:
PRESSURE CONVERSIONS inches ounces/
- Page 73 and 74:
PRESSURE CONVERSIONS inches ounces/
- Page 75 and 76:
Tech Notes Section 1-Eclipse Equipm
- Page 77 and 78:
Air ∆P Through Mixer, "w.c. Table
- Page 79 and 80:
Mixture Pressure, "w.c. 8 6 5 4 3 2
- Page 81 and 82:
ΔP P Across Mixer, "w.c. 50 40 30
- Page 83 and 84:
Tech Notes Flame Temperatures vs. A
- Page 85 and 86:
Tech Notes Available Heat—Extende
- Page 87 and 88:
Tech Notes Nozzle Mixing Burners Ra
- Page 89 and 90:
Tech Notes Nozzle Mixing Burners Ra
- Page 91 and 92:
Tech Notes Nozzle Mixing Burners Ra
- Page 93 and 94:
Tech Notes Section 2 Sheet C-5 Nozz
- Page 95 and 96:
Disadvantages • Most expensive of
- Page 97 and 98:
Tech Notes Nozzle Mixing Burners Ex
- Page 99 and 100:
Tech Notes Backpressure Compensatio
- Page 101 and 102:
4) lb./million Btu to ppm at 0% O2
- Page 103 and 104:
Tech Notes Recuperator Efficiency:
- Page 105 and 106:
TechNotes NFPA Requirements for Gas
- Page 107 and 108:
Tech Notes IRI Requirements For Gas
- Page 109 and 110:
Continued from previous page Item D
- Page 111 and 112:
References Gross Heating Value Liqu
- Page 113 and 114:
Figure 1: Immersion Tube Efficiency
- Page 115 and 116:
Figure 1: Thermal Efficiency of a S
- Page 117 and 118:
References: Thermal Manual of Subme
- Page 119 and 120:
Tech Notes Determining % O 2 in a R
- Page 121:
Litho in U.S.A.