Section 06 Custom Chrome Europe Catalog 2024

APPAREL
SEATS &
TOURING
FOOT
CONTROLS
i.SED 3-In-1 Turn Signal Module
• For mounting Indicators with higher wattage than original,
indicators on vehicles where the ground is „plus“ but not
„minus“ as usual or „DF“ products on vehicles where the
indicators ground is switched but not the plus as usual. Note:
On some models, the “LED displays” option must be activated
PART# FITMENT DESIGN UNIT
912573
14-20 Sportster, 12-17
Dyna, 11-23 Softail, 14-
i.SED - V
23 Touring, 14-23 Trike,
12
21-23 Sportster RH, 21-23
Pan America
Set
i.BOS Turn Signal Module
• Provides correct function of the control and hazard
light, e.g. when using DF versions for Harley Davidson
models with Can-Bus.
PART# DESIGN UNIT
912572 i.BOS - CL 1 Set
HAND
CONTROLS
LIGHTING
ELECTRICAL
EXHAUST
m.button
Another innovation from motogadget: the m.button.
It’s a big help - in combination with the new m.unit blue, basic and m.unit v.2
- in reducing ‘cable clutter’ and simplifying wiring harnesses. Integrated into
the handlebar tube - or any other adequate location - this tiny cylinder will
electrically connect all handlebar instruments, switches and buttons. Using
state-of-the-art bus technology, the m.button digitally processes signals and
transmits them to the m.unit over a thin cable. The electrical consumers
will then be switched inside the m.unit. All control wires are moved into
the handlebar. This saves space, weight, labour and time. A ‘must have’ for
custom bikes with clean-look handlebars.
690974 mo.Button
CBW1 Can-Bus Resistor
• The CBW1 resistor provides a required electrical load for your
vehicle, which, if the dip switches are set correctly, will result
in no flashing of the accessory flashers in the cockpit. If the
accessory indicators fail due to an electronic fault, an error
message is immediately displayed in the cockpit. Up to 2
channels can be operated, such as turn signals at the rear left
and turn signals at the rear right. The CBW1 can also be used
on vehicles with original LED turn signal equipment.
• Dimensions: Height = 11mm, Width = 31mm (without straps),
Width = 46mm (with tabs), Length = 40mm
• Cable length = 200mm with pins
• Resistance values: 150 ohms, 200 ohms, 170 ohms, 240 ohms,
300 ohms, 400 ohms, 600 ohms, 1200 ohms
PART#
UNIT
913218 Each
INTAKE
ENGINE
GASKETS
TRANNY &
CLUTCH
DRIVELINE
WHEELS, TIRES
& BRAKES
FRAMES
FORKS &
SHOCKS
Front ABS 12“ Extension Harness
• 12“ extension
• Allows a simple way to safely lengthen your front end while
still having ABS connected properly
• 100% Plug-n-Play
Fitment Note: ABS Models, Length: 304.8 mm, Unit: Each,
Qty.: 1
PART#
FITMENT
921795 08-23 Touring, except 17-22 FLHR, 17-18 FLHRC, 18-23
FLHRXS
921796 17-22 FLHR, 17-18 FLHRC, 18-23 FLHRXS
CB2 Position Light Control Box
• With few work steps install the CB2 PL CONTROLBOX between
the 2in1 indicator and activate a new great safety feature.
During the flashing process, the CB2 box switches the position
light off and starts only again after the flashing process. Thus,
the flashing signal is better perceived in road traffic.
• Dimensions: Diameter: 11 mm, Length: 17,5 mm
PART# FITMENT UNIT
913219 Not suitable for headlights with position light. Pair
SHEETMETAL
INSTRUMENTS
& GAUGES
LUBRICANTS &
CHEMICALS
TOOLS &
EQUIPMENT
for more details check www.custom-chrome-europe.com
6.17