Section 06 Custom Chrome Europe Catalog 2024

APPAREL
Automatic Daytime running light switch
• This electronic relay contains 2 power outputs what can drive
60 Watt / each. A daylight sensor detect if the ambience light
is dark or bright and the device switch between daytime
running light and low beam, depending of the ambience light.
The switch time from daytime running light to low beam is
immediately for situations when you ride from a bright place
in a darker place. The switch time from low beam to daytime
running light is adjusted to 3 seconds in order to get the the
light sensitivity down against light reflections. You can adjust
and store the trigger value of the ambience light in 60 steps.
PART#
UNIT
914346 Each
Ground Split Terminal Splitter
Many electrical problems at the bike result from a bad
connection to the minus pole of the battery. The chassis is often
in use as minus pole, which is not the best connection due to
rust, paint or dirt at the contact screw. The Gnd-Split is a 4
pin divider that can be screwed directly to the minus pole of
the battery. It can split up to 4 cables with a maximum size of
AWG14.
Part#: 919978 , Length: 20 mm, Height: 16 mm, Width: 20
mm, Unit: Each , Qty.: 1
Elektronicbox Version B
The B-Box is our response from some clients, who prefer an easy
mechanical implementation of the control box in a bike and who
don´t take care about a bit bigger size compare to our other
devices. The B-Box can be controlled with the standard ignition
switch. 8 implemented status led´s allow a fast check while the
installation or the adjustment of the different functions. A 20
Ampere inline fuse in the main line is integrated. However, the
outputs are short circuit protected and self resetting.
• Functions:
• Switch - output for parking light / Plate light / speedo etc.
• Ignition (with or without side stand switch control)
• Starter (with or without neutral switch control)
• Headlight with button or switch control
• Integrated flasher relay, control with buttons or switches
• Brake light with flasher option
• Horn
Part#: 917230 , Length: 92 mm, Height: 36 mm, Width: 50
mm, Unit: Each , Qty.: 1
SEATS &
TOURING
FOOT
CONTROLS
HAND
CONTROLS
LIGHTING
ELECTRICAL
EXHAUST
INTAKE
ENGINE
GASKETS
Multi Flasher Plus Relay
This is a small flasher controller for pushbuttons in a small
package that will fit in every handlebar. This device is controlled
via 12 Volt inputs, what make it easier to implement in an
existing OEM harness if no minimal wiring is required. An auto
cancel function can be activated. It switch off the indicators after
a while if no button is pushed.
Part#: 917233 , Length: 38 mm, Height: 11 mm, Width: 16
mm, Unit: Each , Qty.: 1
TRANNY &
CLUTCH
DRIVELINE
WHEELS, TIRES
& BRAKES
FRAMES
Flasher Merger
The Flasher Merger is connected between the 2 direction
indicators and the indicator led in the dashboard or speedo. Two
diodes are implemented. The module allows the control of one
indicator led for both flashers. The maximum load is 100 mA or
1,2 Watt. The module is waterproof potted what makes it simple
to install without the need to wire 2 diodes, insulate it and try to
get it waterproofed.
Part#: 917975 , Length: 14 mm, Height: 5 mm, Width: 14
mm, Unit: Each , Qty.: 1
Minimal Indicator
The minimal indicator is a small microcontroller module and
a 3-color LED. The controller drives the different colors of the
LED and allows to indicate all necessary functions of your bike
with just one LED. Allows to display 2 or 3 events at the same
time easily. The small dimensions allows the implementation
inside the head light or even in the handle bar. Cleans up your
dashboard for a much cooler look.
• You can indicate the following functions with one LED:
• Flasher left and right
• High beam
• Neutral
• Oil Pressure
Part#: 917235 , Length: 38 mm, Height: 11 mm, Width: 16
mm, Unit: Each , Qty.: 1
FORKS &
SHOCKS
SHEETMETAL
INSTRUMENTS
& GAUGES
LUBRICANTS &
CHEMICALS
TOOLS &
EQUIPMENT
for more details check www.custom-chrome-europe.com
6.27