CSI 2130 Reference Manual - Emerson Process Management

More documents

Recommendations

Info

Changing the Battery To change the CSI 2130 analyzer’s battery pack: 1. Make sure the analyzer is off, the battery charger power supply is disconnected from the analyzer, and that the hand straps are removed. 2. Remove the rubber boot from the analyzer. 3. On the back of the analyzer, remove the six screws on the back panel. Then remove the panel. 4. Carefully remove the battery pack from the battery compartment. Analyzer with back cover removed 5. Unplug the battery from the connector to the analyzer. Unplugging the battery from the connector. 1-28 Introduction to the CSI 2130
Battery Use and Care 6. Connect the new battery pack and insert it into the analyzer case. 7. Tuck the battery pack foam inserts into the case on the sides of the battery pack. Make sure the foam inserts do not interfere with the installation of the bottom panel. 8. Replace the bottom panel and screws. 9. Replace the rubber boot and any hand straps removed. 1-29
Page 1 and 2: Reference Manual CSI 2130 Machinery
Page 3 and 4: Patents The product(s) described in
Page 5: Software Technical Help Software Te
Page 8 and 9: Chapter 3 • Data Transfer 8 Memor
Page 10 and 11: 10 Input Setup . . . . . . . . . .
Page 12 and 13: Precautions Any product damage due
Page 14 and 15: Single- and Dual-Channel Versions o
Page 16 and 17: 2130 2-channel volts adapter 1-chan
Page 18 and 19: Unpacking the CSI 2130 Unpack the C
Page 20 and 21: 4. Pull the plain end completely th
Page 22 and 23: Panels In addition to the battery c
Page 24 and 25: Charger Input Reset Switch This sma
Page 26 and 27: Front Panel: Buttons, Indicators, a
Page 28 and 29: Battery Use and Care A rechargeable
Page 30 and 31: Screen for CSI 2130 with Ethernet P
Page 32 and 33: Note It is not necessary to press t
Page 34 and 35: To discharge the battery: 1. First
Page 36 and 37: If the external power supply/charge
Page 40 and 41: 1-30 Introduction to the CSI 2130
Page 42 and 43: Analyze and Advanced Analyze “Ana
Page 44 and 45: 2. . .Press File Up and File Down t
Page 46 and 47: Note Transferring files to and from
Page 48 and 49: Select All Files: Selects all the f
Page 50 and 51: Set Display Units Display Units def
Page 52 and 53: Set dB Ref: Configure Acceleration,
Page 54 and 55: USB Port Connection To begin using
Page 56 and 57: Ethernet Card Connection Communicat
Page 58 and 59: Disable DHCP to activate Set IP Add
Page 60 and 61: Set Host Info: Enter the Host Name,
Page 62 and 63: Note Do not change the Host Port ID
Page 64 and 65: Select All Programs: Press to selec
Page 66 and 67: Possible Base Firmware Error Messag
Page 68 and 69: The screen below shows that the “
Page 70 and 71: 3. . .With the CSI 2130 off, press
Page 72 and 73: How do I .. Delete a Program? Cauti
Page 74 and 75: From the Folders view, verify the c
Page 76 and 77: ALT: Alternate Screens ALT Screen P
Page 78 and 79: General Setup Use General Setup to
Page 80 and 81: Set Backlight Time: Automatically d
Page 82 and 83: Set Hold Time: determines the lengt
Page 84 and 85: Set Time Zone: Scroll through pages
Page 86 and 87: Erase PReg: clears the internal set
Page 88 and 89:
Connect For Printing Connect For Pr
Page 90 and 91:
Remote users of the CSI 2130 analyz
Page 92 and 93:
The user may clear old information
Page 94 and 95:
The CSI 2130 setup must match the "
Page 96 and 97:
Install from a specific location 5.
Page 98 and 99:
Note The exact format and content o
Page 100 and 101:
Save data flagged bad reading: When
Page 102 and 103:
Route Overrides The Route Overrides
Page 104 and 105:
Change Point Definition For Firmwar
Page 106 and 107:
Upon a successful connection, a new
Page 108 and 109:
When the user has completed the dat
Page 110 and 111:
If the auto-analyze option is enabl
Page 112 and 113:
More than one report or plot may be
Page 114 and 115:
The cover page is saved as part of
Page 116 and 117:
Standalone Data Transfer Applicatio
Page 118 and 119:
Model # Description Comments A06280
Page 120 and 121:
Note Connect the D24860 triax cable
Page 122 and 123:
Using a Route The simplest way to s
Page 124 and 125:
Selecting Measurement Points There
Page 126 and 127:
Route Data Collection The Route Dat
Page 128 and 129:
Route Data Collection: Measurement
Page 130 and 131:
• High Signal - When using DL-A t
Page 132 and 133:
Previous Equipment takes you to the
Page 134 and 135:
Field Alert places a field alert wa
Page 136 and 137:
Fault Frequenciese Note The ID and
Page 138 and 139:
Note If multiple data sets are stor
Page 140 and 141:
User Setup User Setup allows you to
Page 142 and 143:
Set HFD Averages: Opens a box where
Page 144 and 145:
True Peak: Is obtained from the wav
Page 146 and 147:
Group Status Timer: Control the aut
Page 148 and 149:
New Sensor Power: If sensor power o
Page 150 and 151:
Note Automatic display occurs only
Page 152 and 153:
Unselect All Routes: Deselects all
Page 154 and 155:
Print Route Report Printing a Route
Page 156 and 157:
5-36 Route
Page 158 and 159:
Notes Add Notes 4 To attach a note
Page 160 and 161:
Up/Down Arrows: Allow you to scroll
Page 162 and 163:
Downloading Routes and Uploading Da
Page 164 and 165:
Once you have chosen a storage loca
Page 166 and 167:
Multiple Route Load (MRL) allows Ro
Page 168 and 169:
Time Discrepancy The time set on yo
Page 170 and 171:
Analysis Experts Analysis Experts o
Page 172 and 173:
• If data has already been collec
Page 174 and 175:
Press the More Experts function key
Page 176 and 177:
If the running speed is at a resona
Page 178 and 179:
Order Tracking The Order Tracking e
Page 180 and 181:
If Average Mode is set to “Synchr
Page 182 and 183:
Using Analysis Experts Let this cha
Page 184 and 185:
In Manual Analyze, you can set your
Page 186 and 187:
You can set sensor parameters for b
Page 188 and 189:
Change Sensor Type: Press this key
Page 190 and 191:
Press Connect for Transfer to dump
Page 192 and 193:
Press the Manual Analyze key on the
Page 194 and 195:
Show RPM: Press Show RPM to display
Page 196 and 197:
PeakVue passes the input signal thr
Page 198 and 199:
Select Input: Use this dropdown men
Page 200 and 201:
Set Spectra Params: Allows you to s
Page 202 and 203:
Set Averaging: When vibration is me
Page 204 and 205:
Waveform A vibration waveform is a
Page 206 and 207:
Overall Setting the Analyze mode to
Page 208 and 209:
DC Volts and Temperature. When meas
Page 210 and 211:
For information about Tach Setup, S
Page 212 and 213:
Set Center Frequency: This is the f
Page 214 and 215:
Set Cascade Params: Use this menu t
Page 216 and 217:
A minimum delay exists because of t
Page 218 and 219:
Set Tach Start: This is only availa
Page 220 and 221:
Set Average Enable: Select this fun
Page 222 and 223:
The Analyze Setup Screen in Bandpas
Page 224 and 225:
Cross Channel Phase Setting the Ana
Page 226 and 227:
Plot Functions Use plotting tools t
Page 228 and 229:
You can view up to four plots at on
Page 230 and 231:
Store Data: Stores your data to a r
Page 232 and 233:
Harmonic Family Cursors When this c
Page 234 and 235:
Compress X Axis: Compresses the dis
Page 236 and 237:
Cascade Plots Cascade acquisitions
Page 238 and 239:
Auto Correlation Waveform plots hav
Page 240 and 241:
When selected, the lines showing th
Page 242 and 243:
Edit Job Setup Route Equipment: Job
Page 244 and 245:
Delete Meas: Delete a measurement p
Page 246 and 247:
If using USB or Serial connections,
Page 248 and 249:
Analyze Mode Press Manual Analyze f
Page 250 and 251:
Analyze Setup for Impact Mode Set S
Page 252 and 253:
Note By default, the force hammer i
Page 254 and 255:
Sensor Setup Sensor Setup screen wi
Page 256 and 257:
Impact Acquisition Process Place th
Page 258 and 259:
Clear Window Overlay: Removes the w
Page 260 and 261:
Analyze Setup Setting up an Advance
Page 262 and 263:
Two Channel Plot Setup Press Plot S
Page 264 and 265:
Set Plot Options Explained Waveform
Page 266 and 267:
The stacked plot option displays pl
Page 268 and 269:
Applications and Insights Related t
Page 270 and 271:
Resonance Explained Resonance is a
Page 272 and 273:
The harder tips should be used when
Page 274 and 275:
The phase measurement provides the
Page 276 and 277:
Testing performed only to identify
Page 278 and 279:
For the exploratory impacts try usi
Page 280 and 281:
Summary Once a resonant frequency h
Page 282 and 283:
CSI 2130 Advanced Transient Applica
Page 284 and 285:
If data has been acquired on a poin
Page 286 and 287:
Note The job manager mode is explai
Page 288 and 289:
F7: This key will end the “Transi
Page 290 and 291:
Changing Fmax adjusts the Sample Ra
Page 292 and 293:
During data collection, the 2130 sc
Page 294 and 295:
The Data Display Settings that can
Page 296 and 297:
plot. Pressing the Scroll Left and
Page 298 and 299:
F6: This key sets the format for ho
Page 300 and 301:
ALT 2: F1: This key does not set RP
Page 302 and 303:
F12: Pressing this key will compres
Page 304 and 305:
Full Transient - Input: A Full Tran
Page 306 and 307:
Orbit This overview is only a limit
Page 308 and 309:
This is the Full transient Input B
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Order based colored Waterfall plot.
Page 318 and 319:
Full Transient Input A + RPM plot +
Page 320 and 321:
Hereinafter the term “structure
Page 322 and 323:
All other functionalities are greye
Page 324 and 325:
F4: Press this key to select the nu
Page 326 and 327:
F6: Press this key to change the me
Page 328 and 329:
Typical screen for an ODS job: 10-1
Page 330 and 331:
Typical screen for an ODS/MODAL job
Page 332 and 333:
F10: Press this key to switch betwe
Page 334 and 335:
F3: Press this key to change the po
Page 336 and 337:
10-18 ODS Modal
Page 338 and 339:
Input Specifications Input Signals
Page 340 and 341:
Prefilters The following filters ar
Page 342 and 343:
CSI 2130 with Ethernet port and SD
Page 344 and 345:
A-8 -
Page 346 and 347:
G-2 Amplitude the magnitude (RMS, p
Page 348 and 349:
G-4 If a quantity X is in RMS ampli
Page 350 and 351:
G-6 ICM Influence Coefficient Metho
Page 352 and 353:
G-8 Phase 1xRPM phase represents th
Page 354 and 355:
G-10 Trigger causes the machinery a
Page 356 and 357:
Coast Down Peak and Phase 6-8 Coast
Page 358 and 359:
Cursor Type 7-49 Expand X 7-48, 7-5
Page 360:
I-6
show all

CSI 2130 Reference Manual - Emerson Process Management

Create successful ePaper yourself

Delete template?

Save as template?