REPAIR MANUAL - Euromachines

More documents

Recommendations

Info

82 SECTION 10 - ENGINE - CHAPTER 1 Checking connecting rods the parallelism of the connecting rod (2) axes Check instrument 380001003 (4) as follows. using the connecting rod (2) on the self--centring spindle Fit of tool 380001003 (4) and lock it with the screw (3) (5). the spindle (3) on the “V” prisms, setting the con- Put rod (2) on the stop bar (1). necting Checking twisting the twist of the connecting rod (2) by compar- Check two points (A and B) of the pin (4) on the horizoningt tal plane of the connecting rod axis. the support (1) of the dial gauge (5) so that Position pre--loads by ∼ 0.019 in. (∼ 0.5 mm) on the pin (4) this point A and reset the dial gauge (5). Move the at (3) with the connecting rod (2) and on the op- spindle side (B) of the pin (4) compare any deviation: posite difference between A and B must be no greater the than 0.003 in. (0.08 mm). Checking bending the bend of the connecting rod (3) by compar- Check two points (C and D) of the pin (4) on the vertical ing of the connecting rod axis. Position the vertical plane (2) of the dial gauge (1) so that this rests on support pin (4) at point C as shown in the figure. Swing the connecting rod to and fro, seeking the highest the of the pin and reset the dial gauge (1) in this position Move the spindle with the connecting rod condition. and on the opposite side D of the pin (4) repeat (3) check for the highest point. The difference be- the points C and D must be no greater than tween in. (0.08 mm). 0.003 604.82.321.00 -02- 2005 MIF1045A MIF1046A MIF1047A 170 171 172
MEASUREMENTS AND <strong>REPAIR</strong>S CHECKS, PISTONS CAUTION all parts carefully. Handle not put your hands or fingers between parts. Do the prescribed safety clothing, including Wear gloves and safety footwear. goggles, all parts carefully before proceeding with the Clean described below. operations MIF1034A Measuring the piston diameter a micrometer (2) measure the diameter of the Using (1), and check the cylinder liners to determine piston state of wear of the liners and pistons (see the 10 and 11). pages the clearance is not between 0.009 et 0.0115 in. If to 0.294 mm), it will be necessary to ream, re- (0.252 the liners and fit oversize pistons and rings (see bore 10 and 11). pages The diameter must be measured at a dis- NOTE: of 2.40 in. (61 mm) from the base of the piston tance skirt. SECTION 10 - ENGINE - CHAPTER 1 83 Normal dimensions (mm) piston data MIF1035A 173 174 604.82.321.00 -02 - 2005
Page 1:
REPAIR MANUAL NEW HOLLAND VL570 VM3
Page 4 and 5:
2 SPECIFICATIONS 604 82 321 00 -02-
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
8 SPECIFICATIONS WEIGHT 604 82 321
Page 12 and 13:
10 SPECIFICATIONS 604 82 321 00 -02
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
16 SPECIFICATIONS DRIVE (follows) C
Page 20 and 21:
18 SPECIFICATIONS COMMERCIAL DESCRI
Page 22 and 23:
20 SPECIFICATIONS COMMERCIAL DESCRI
Page 24 and 25:
Page 26 and 27:
2 604 82 321 00 -02- 2005
Page 28 and 29:
2 SECTION 00 - MAINTENANCE - CHAPTE
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
10 SECTION 00 - MAINTENANCE - CHAPT
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
2 SECTION 05 - MACHINE PREPARATION
Page 46 and 47:
4 SECTION 05 - MACHINE PREPARATION
Page 48 and 49:
2 SECTION 10 - ENGINE - CHAPTER 1 G
Page 50 and 51:
4 SECTION 10 - ENGINE - CHAPTER 1 G
Page 52 and 53:
6 SECTION 10 - ENGINE - CHAPTER 1 6
Page 54 and 55:
8 SECTION 10 - ENGINE - CHAPTER 1 6
Page 56 and 57:
10 SECTION 10 - ENGINE - CHAPTER 1
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79: 32 SECTION 10 - ENGINE - CHAPTER 1
Page 162 and 163: 2 352 604.82.321.00 -02- 2005 SECTI
Page 164 and 165: 4 604.82.321.00 -02- 2005 SECTION 1
Page 166 and 167: 2 SECTION 29 - HYDROSTATIC TRANSMIS
Page 174 and 175: 10 SECTION 29 - HYDROSTATIC TRANSMI
Page 176 and 177: 12 SECTION 29 - HYDROSTATIC TRANSMI
Page 178 and 179:
1 14 SECTION 29 - HYDROSTATIC TRANS
Page 180 and 181:
16 SECTION 29 - HYDROSTATIC TRANSMI
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
2 SECTION 33 - BRAKES AND CONTROLS
Page 204 and 205:
4 SECTION 33 - BRAKES AND CONTROLS
Page 206 and 207:
2 SECTION 35 - HYDRAULIC SYSTEMS -
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
2 SECTION 39 - FRAMES - CHAPTER 1 3
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
10 SECTION 39 - FRAMES - CHAPTER 1
Page 264 and 265:
2 SECTION 41 - STEERING - CHAPTER 1
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
2 SECTION 44 - WHEELS - CHAPTER 1 6
Page 272 and 273:
4 SECTION 44 - WHEELS - CHAPTER 1 T
Page 274 and 275:
6 SECTION 44 - WHEELS - CHAPTER 1 6
Page 276 and 277:
2 SECTION 50 - CAB CLIMATE CONTROL
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
2 SECTION 55 - ELECTRICAL SYSTEMS -
Page 286 and 287:
27 4 SECTION 55 - ELECTRICAL SYSTEM
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
10 SECTION 55 - ELECTRICAL SYSTEMS
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
2 s 0 ie r 0 s e 6 M 4 d V 0 a n 6
Page 312 and 313:
2 0 rie s 0 0 s e 7 M 3 d V 0 a n 7
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
X61 46 SECTION 55 - ELECTRICAL SYST
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392 and 393:
Page 394 and 395:
Page 396 and 397:
2 SECTION 58 - ATTACHMENTS/HEADERS
Page 398 and 399:
Page 400 and 401:
Page 402 and 403:
Page 404 and 405:
Page 406 and 407:
Page 408 and 409:
Page 410 and 411:
Page 412 and 413:
Page 414 and 415:
Page 416 and 417:
Page 418 and 419:
2 SECTION 60 - PRODUCT FEEDING - CH
Page 420 and 421:
Page 422 and 423:
Page 424 and 425:
Page 426 and 427:
10 SECTION 60 - PRODUCT FEEDING - C
Page 428 and 429:
Page 430 and 431:
Page 432 and 433:
Page 434 and 435:
Page 436 and 437:
Page 438 and 439:
2 SECTION 74 - CLEANING - CHAPTER 1
Page 440 and 441:
Page 442 and 443:
Page 444 and 445:
Page 446 and 447:
2 SECTION 80 - GRAPE STORAGE - HOPP
Page 448 and 449:
Page 450 and 451:
Page 452 and 453:
Page 454 and 455:
10 SECTION 80 - GRAPE STORAGE - HOP
Page 456 and 457:
2 SECTION 88 - ACCESSORIES - CHAPTE
Page 458 and 459:
Page 460 and 461:
Page 462 and 463:
Page 464 and 465:
A2 H G B E 10 SECTION 88 - ACCESSOR
Page 466 and 467:
12 SECTION 88 - ACCESSORIES - CHAPT
Page 468 and 469:
Page 470 and 471:
Page 472 and 473:
Page 474 and 475:
Page 476 and 477:
Page 478 and 479:
Page 480 and 481:
Page 482 and 483:
Page 484 and 485:
Page 486 and 487:
Page 488 and 489:
Page 490 and 491:
Page 492 and 493:
Page 494 and 495:
Page 496 and 497:
Page 498 and 499:
Page 500 and 501:
Page 502 and 503:
Page 504 and 505:
show all

REPAIR MANUAL - Euromachines

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?