Concealed Hinges

353 

Hinges and Stays 

Concealed Hinges Wood/Glass ......................................................355–429 

Institutional Hinges..........................................................................430–436 

Mitre Hinges ...........................................................................................437 

Drill In Concealed Hinges ................................................................438–439 

Glass Door Hinges..........................................................................440–443 

Piano and Butt Hinges ....................................................................444–445 

Furniture Hinges..............................................................................446–449 

Pivot Hinges....................................................................................450–451 

Flap Hinges ............................................................................................452 

Flap Stays.......................................................................................453–460 

Call 1-800-423-3531 from anywhere in Canada - www.hafele.com 

Dimensional data not binding. We reserve the right to alter specifications without notice.

Dimensional data not binding. We reserve the right to alter specifications without notice. 



Lid Stays and Lid Door Hinges .......................................................461–469 

Bench Seat Hinges.................................................................................470 

Lid/Flap Stays .................................................................................471–476 

Swing Up Fittings............................................................................477–481 

Aluminum Doors and Hinges...........................................................482–488 

Bumpers and Trim Caps .................................................................489–490 

354

Concealed Hinges 

DUOMATIC 

Installing DUOMATIC A mounting plates with slide on system 

1 

Place hinge on mounting plate. Positioning with pre-determined end 

stop. 

2 

Tighten mounting plate screw. 

3 

After installation there must be a distance of 0.7 mm from door to 

side panel. Safety feature. 

Dimensions in mm 

Inches are approximate 

355 

0.7 

4 

Remove hinge arm from mounting plate by loosening the mounting 

plate screw. 

1 

Join the two points marked by an arrow. 


Installing with DUOMATIC SM mounting plates with quick fixing 

system 

2 

Turn slightly 

3 

and apply light pressure. 

4 

Remove hinge arm from mounting plate by applying pressure on the 

two points marked by an arrow. 





DUOMATIC 

Mounting methods for concealed hinges 

Screw Mounting 

Cup mounting with screws with countersunk head. 

Quick mount 

Cup mounting with pre-mounted spreading dowels. 

Mounting methods for mounting plates 

Screw Attachment 

Attach with wood screws, with special screws or with pre-mounted 

special screws and spreading dowels. 

Attachment of door to cabinet 

Clip-on without Tools 

No tools required for mounting the hinge arm onto the SM 

mounting plate and for removing it. 

Press Fit Mounting 

Machine insertion of cup by press fitting. 



Tooless Mounting 

Installation and removing by lever action, no tools required. 

Press Fit Mounting 

Machine insertion by press fitting with pre-mounted dowels. 

Slide on system 

The hinge arm is slid onto the mounting plate and attached 

with pre-mounted screw. 



356


DUOMATIC 

Depth adjustment 

1 

Depth adjustment of door with DUOMATIC A mounting plates 

with slide on system 

It is possible to adjust the door front up to +2.8 mm. The slot on the 

metal bottom plate allows the hinge to slide. Afterwards the screw 

must be re-tightened. 

2 

Depth adjustment of door with DUOMATIC SM cruciform 

mounting plates with quick mounting system 

With the DUOMATIC mounting plates with quick mounting system, a 

depth adjustment of the door from -0.5 mm up to +2.8 mm is 

possible via eccentric. It is not necessary to loosen screws. 

Cat. No. 329.68.X, 329.69.X, 329.73.X 

3 

Depth adjustment of door with DUOMATIC SM straight and 

cruciform mounting plates with quick mounting system 

With the DUOMATIC mounting plates with quick mounting system, a 

depth adjustment of the door from -0.5 mm up to +2.8 mm is 

possible via eccentric. It is not necessary to loosen screws. 

Cat. No. 329.67.X, 329.71.X 



357 






DUOMATIC 

Lateral adjustment 

Lateral adjustment of door with DUOMATIC concealed 

hinges 

A particular adjustment method allows lateral adjustment of 

the door, where the value of 0.7 mm remains unchanged. 

The adjusting screw produces the lateral travel of the hinge 

arm from -1.5 mm up to +4.5 mm. This value is reduced to 

-0.5 mm when using profile door hinges and mini hinges. 

The door moves with respect to the furniture side without 

coming apart. There are no further adjustments needed. 

Height adjustment 

1 

Height adjustment of door with DUOMATIC mounting plates 

with slide on and quick mounting system 

Height adjustment of door of ±2 mm is possible by loosening the two 

mounting screws. The slots allow the mounting plates to slide in both 

directions. Afterwards the screws must be re-tightened. 

2 

Height adjustment of door with DUOMATIC cruciform mounting 

plates with quick mounting system 

Height adjustment of door ±2 mm is possible via eccentric. It is not 

necessary to loosen screws. 

3 

Height adjustment of door with DUOMATIC straight mounting 

plates with quick mounting system 

Height adjustment of door ±2 mm is possible via eccentric. It is not 

necessary to loosen screws. 





358


DUOMATIC 

Mounting 

Hinge arm length 

Door offset 

Choice of mounting plate 

Distance 

Hinge arm height 

with mounting plate 

Door overlay 

Door 

Gap 

Distance to cup 

Side panel 

Door gap 


Gap 

Door overlay 

Mounting situations with corner applications 

Inset 

Door outer edge and 

cabinet inner edge are 

in line. 

Minimum 

gap 

Half overlay 

Door inner edge and 

cabinet inner edge are 

in line. 

Number of concealed hinges per door 

The graph shown gives guideline information only. A trial 

installation is recommended. 

The number of concealed hinges per door depends on: 

• Door width and height 

• Door weight 

• Door material 

According to the example graph, three concealed hinges have 

to be mounted at a door height of 1,500 mm and a door 

weight of 9 to 12 kg. 

Determination of required minimum gap 

Full overlay mounting 

Straight hinge arm 

Overlay 

Door outer edge and 

cabinet outer edge are 

in line. 

The required minimum gap depends on the type of hinge, distance to cup and 

door thickness. After the dimensions of distance to cup and door thickness has 

been determined, the minimum gap can be looked up in the application table. 



359 

Half overlay mounting 

Cranked hinge arm 

2500 

2000 

Door height mm 

1500 

Max. overlay 

Depending on 

geometry of concealed 

hinge. 

1000 

500 

4–9 

600 


Inset mounting 

High cranked hinge arm 

9–12 12–18 17–22 

600 600 600 

2 3 4 5 

Mitre 

Door inner and outer 

edge and cabinet inner 

edge are in line. 

Door weight kg 

Door width mm 

Number of hinges 

Example 

With door overlay of 10 mm and a distance to cup of 3 mm, a 

mounting plate with distance of 6 mm has to be used. 

Door overlay mm 

7 8 9 10 11 12 13 14 15 16 17 18 19 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 9 

Distance to cup Mounting plate distance mm 

Example 

With a door thickness of 19 mm and a distance to cup of 

4 mm a minimum gap of 2 mm is required. 

Door Distance to cup mm 

thickness mm 3 4 5 6 

16 1.2 1.2 1.1 1.1 

18 1.7 1.7 1.6 1.6 

19 2.0 2.0 1.9 1.9 

20 2.4 2.3 2.2 2.9 

22 3.3 3.1 3.0 2.9 

24 4.5 4.2 4.0 3.9 

26-32 Trial installation is recommended 





DUOMATIC for door thickness from 10 mm - Opening angle 105º 

Drilling dimensions 

Screw mount 

Minimum gap 

Minimum 

gap 

Minimum distance 



• Material: Cup and hinge arm: steel 

• Colour: nickel-plated 

• Cup attachment: screw mount 

• Mounting door to cabinet: slide on with DUOMATIC A mounting plates or clip on attachment with DUOMATIC 

SM mounting plates 

• Adjusting facility: Lateral adjustment continuously from -1.5 mm to +4.5 mm 

Height adjustment from -2 mm to +2 

Depth adjustment with DUOMATIC A mounting plates +2.8 mm 

with DUOMATIC SM mounting plates from -0.5 mm to +2.8 mm 

• With self closing spring 



10 0.2 0.2 0.1 0.1 

11 0.3 0.3 0.3 0.2 

12 0.4 0.4 0.4 0.4 

13 0.6 0.6 0.6 0.5 

14 0.8 0.8 0.8 0.7 

15 1.0 1.0 1.0 1.0 

16 1.3 1.3 1.2 1.2 

17 1.6 1.6 1.5 1.5 

18 1.9 1.9 1.8 1.8 

19 2.3 2.2 2.1 2.1 

20 2.7 2.6 2.5 2.4 

Rounding off the edge of door reduces the given values. 

Self-Closing Hinges 


Cup dimensions 

Screw mount 

Minimum gap between 

door and side panel 

Dimensions and gap specifications in 

drawings and tables are calculated: 

• With factory settings 

• With mounting plate distance 0 mm 

• For door offset with max. opening angle 



10 0.0 0.0 0.5 1.5 

11 0.0 0.0 0.7 1.7 

12 0.0 0.0 0.9 1.8 

13 0.0 0.0 1.0 2.0 

14 0.0 0.2 1.2 2.2 

15 0.0 0.4 1.4 2.4 

16 0.0 0.6 1.5 2.5 

17 0.0 0.7 1.7 2.7 

18 0.0 0.9 1.9 2.9 

19 0.1 1.1 2.1 3.1 

20 0.3 1.2 2.2 3.2 



Gap 

Gap 

• Hinge arm: Straight (crank 0 mm) • Hinge arm: Cranked (crank 9 mm) 

Cup attachment Cat. No. 


Screw mount 329.28.600 


Packing: 50 pcs. 




9 10 11 12 13 14 15 16 17 18 19 20 21 

0 1 2 3 4 5 6 7 8 9 10 11 12 

3 4 5 6 0 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 6 

3 4 5 6 9 

3 4 5 6 9 

Distance to cup mm Mounting plate distance mm 




360


DUOMATIC with PUSH system for opening without handle - Opening angle 110º die-cast 


Minimum gap 

Minimum 

gap 



360 A 



16 0.5 0.5 0.5 0.5 

17 0.7 0.7 0.7 0.7 

18 0.9 0.9 0.9 0.9 

19 1.2 1.2 1.2 1.2 

20 1.5 1.5 1.5 1.5 

21 1.8 1.8 1.8 1.8 

22 2.4 2.1 2.1 2.1 

23 3.7 2.7 2.6 2.5 

24 5.1 4.1 3.1 3.0 

25 6.5 5.5 4.1 3.5 

26 7.8 6.8 5.4 4.4 

New 

Item 


• Material: Cup: zinc die-cast; Hinge arm: steel 


• Cup attachment: screw mount, press fit 

• Mounting door to cabinet: slide on with DUOMATIC A mounting plates or clip on attachment 

with DUOMATIC SM mounting plates 

• Adjusting facility: Lateral adjusting continuously from -1.5 mm to +4.5 mm 

Height adjustment from -2 mm to +2 mm 


with DUOMATIC A mounting plates +2.8 mm 


• With self-closing spring 

Drilling dimensions for cup 

attachment 

Screw Mounting Press fit 

Drilling pattern 45/9.5 

Dimensions and gap specifications in drawings and tables 

are calculated: 



• For door offset with maximum opening angle 


between door and 

side panel 

Minimum 

distance 




16 0.0 0.0 1.1 2.0 

17 0.0 0.0 1.3 2.3 

18 0.0 0.3 1.6 2.5 

19 0.0 0.6 1.8 2.8 

20 0.2 0.9 2.1 3.1 

21 0.5 1.2 2.3 3.3 

22 0.8 1.4 2.6 3.6 

23 1.1 1.7 2.9 3.8 

24 1.4 2.0 3.1 4.1 

25 1.7 2.3 3.4 4.3 

26 1.9 2.6 3.6 4.6 

Rounding off the edge of door reduces the given values 





DUOMATIC with PUSH system 


Hinge arm: Straight (crank 0 mm) 

Drilling pattern: 45/9.5 



Press fit 329.17.552 

Quick mount 329.17.580 

Tooless 


329.17.350 


9 10 11 12 13 14 15 16 17 18 19 20 21 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 9 


Full overlay/half overlay mounting 

Hinge arm: Cranked (crank 5 mm) 




Press fit 329.17.562 


Tooless 


329.17.351 


0 1 2 3 4 5 6 7 8 9 10 11 12 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 9 


New 

Item 








Press fit 329.17.561 


Tooless 


329.17.352 


0 1 2 3 4 5 6 7 8 9 10 11 12 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 9 



Hinge arm: High cranked (crank 17 mm) 




Press fit 329.17.570 


Tooless 


329.17.353 


-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 

3 4 5 

0 

3 

3 4 5 6 6 

3 4 5 6 9 




360 B


DUOMATIC for door thicknesses up to 32 mm - Opening angle 94º 

Full overlay mounting with mounting plate 


Minimum gap 

Minimum gap 

Minimum gap between door and side panel 




361 




• Cup attachment: screw mount, press fit, quickmount, tooless 










for cup attachment 

Screw Mount 


Press fit, Quikmount or Tooless 



thickness mm 3 4 5 6 7 8 

16 0.4 0.4 0.4 0.4 0.4 0.4 

18 0.8 0.7 0.7 0.7 0.7 0.7 

20 1.2 1.2 1.1 1.1 1.1 1.1 

22 1.7 1.7 1.6 1.6 1.6 1.5 

24 2.4 2.3 2.3 2.2 2.1 2.1 

26 3.2 3.1 3.0 2.9 2.8 2.8 

28 4.5 4.2 3.9 3.8 3.7 3.6 

30 6.3 5.6 5.3 5.0 4.7 4.5 

32 8.1 7.5 7.0 6.5 6.1 5.8 


Distance to cup mm 

3 4 5 6 7 8 

0.0 0.0 0.0 0.0 0.1 1.1 






DUOMATIC - Self Closing for door thicknesses up to 32 mm - Opening angle 94º 




• Hinge arm: Straight (crank 0 mm) 





Screw Mount 329.01.509 

Press fit 329.01.554 

Quickmount 329.01.590 

Tooless 


329.01.350 


9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 

3 4 5 6 7 8 0 

3 4 5 6 7 8 3 

3 4 5 6 7 8 6 

3 4 5 6 7 8 9 


• Hinge arm: Cranked (crank 9 mm) 




Press fit 329.01.563 


Tooless 


329.01.351 


0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 

3 4 5 6 7 8 0 

3 4 5 6 7 8 3 

3 4 5 6 7 8 6 

3 4 5 6 7 8 9 


• Hinge arm: High Cranked (crank 17 mm) 




Press fit 329.01.581 


Tooless 


329.01.352 


-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 

3 4 5 

0 

3 

3 4 5 6 7 8 6 

3 4 5 6 7 8 9 




362


DUOMATIC - Opening angle 120º 



Minimum gap 



363 

Minimum 

gap 



16 1.0 1.0 1.0 1.0 

17 1.3 1.3 1.2 1.2 

18 1.6 1.5 1.5 1.5 

19 1.9 1.9 1.8 1.8 

20 2.2 2.2 2.1 2.1 

21 3.5 2.5 2.5 2.4 

22 5.0 4.0 3.0 2.8 

23 6.5 5.5 4.5 3.5 

24 8.1 7.1 6.1 5.1 

25 9.6 8.6 7.6 6.6 

26 11.2 10.2 9.2 8.1 


Drilling dimensions for cup attachment 

Screw Mount 


Dimensions and gap specifications in drawings and tables are calculated: 
















Press fit, Quickmount, or Tooless 



Minimum 

distance 



16 0.0 0.0 0.3 1.2 

17 0.0 0.0 0.7 1.6 

18 0.0 0.2 1.1 2.0 

19 0.0 0.6 1.5 2.4 

20 0.1 1.0 1.9 2.8 

21 0.5 1.4 2.3 3.3 

22 0.9 1.8 2.8 3.7 

23 1.3 2.2 3.2 4.1 

24 1.7 2.6 3.6 4.5 

25 2.1 3.1 4.0 4.9 

26 2.5 3.5 4.4 5.3 






200 Series - Salice 

Image 

Change 

Image 

Change 

Gap 

Gap 





• Drilling pattern: 45/9.5 

• Material: Cup: steel 

Hinge arm: steel: Finish: nickel-plated 


Screw-mount 329.03.503 

Press-fit 329.03.558 


Tooless 329.03.590 



9 10 11 12 13 14 15 16 17 18 19 20 21 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 9 




• Drilling pattern: 45/9.5 

• Material: Cup: steel 

Hinge arm: steel: Finish: nickel-plated 


Screw-mount [329.03.512] 

Press-fit [329.03.567] 

Quickmount [329.03.582] 

Tooless [329.03.592] 



Number 

Change 

0 1 2 3 4 5 6 7 8 9 10 11 12 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 9 




364


DUOMATIC - Opening angle 165º 



Minimum gap 



365 


Screw Mount 


Dimensions and gap specifications in drawings and tables are calculated: 




Minimum 

gap 

Outer dimensions and distances 

The door swings out laterally up to 5.5 mm when 

opened. Distance with hinge with straight arm, mounting 

plate height 0 mm and distance to cup 3 mm. 













Press fit, Quickmount or Tooless 




16 0.0 0.0 0.0 0.0 0.0 0.0 

18 0.0 0.0 0.0 0.0 0.0 0.0 

20 0.0 0.0 0.0 0.0 0.0 0.0 

22 0.7 0.1 0.1 0.1 0.1 0.1 

24 2.7 1.8 1.2 0.9 0.7 1.6 

26 4.6 3.8 3.0 2.5 2.0 1.7 

28 7.9 6.9 5.9 4.9 3.9 3.2 






DUOMATIC - Self closing 




8- distance to cup Gap 

1+ distance to cup 

Gap 

6+ distance to cup Gap 


Cup attachment, drilling pattern: 45/9.5 



Cat. No. 


Press fit 329.07.654 


Tooless 


329.07.690 


9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 

3 4 5 6 7 8 0 

3 4 5 6 7 8 3 

3 4 5 6 7 8 6 

3 4 5 6 7 8 9 




Cat. No. 


Press fit 329.07.663 


Tooless 329.07.692 



0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 

3 4 5 6 7 8 0 

3 4 5 6 7 8 3 

3 4 5 6 7 8 6 

3 4 5 6 7 8 9 


• Hinge arm: High Cranked (crank 17 mm) 


Cat. No. 


Press fit 329.07.670 


Tooless 329.07.693 



-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 

3 4 5 

0 

3 

3 4 5 6 7 8 6 

3 4 5 6 7 8 9 




366


DUOMATIC - Self closing for Glass Doors - Opening angle 94° 









367 


• Material: Cup: plastic; Hinge arm: steel 












Gap 




9 10 11 12 13 14 15 16 17 18 19 

5.5 6.5 0 

5.5 6.5 3 

5.5 6.5 6 

5.5 6.5 9 


Full overlay / 

half overlay mounting 


Gap 

• Hinge arm: High cranked (crank 7 mm) 





-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 

5.5 6.5 0 

5.5 6.5 3 

5.5 6.5 6 

5.5 6.5 9 


Gap 



Screw mount 



329.21.502 

4 5 6 7 8 9 10 11 12 13 14 

5.5 6.5 0 

5.5 6.5 3 

5.5 6.5 6 

5.5 6.5 9 





DUOMATIC - For wooden doors with negative angle mounting - Opening angle 120º 

-30º Corner application with mounting plate 





• Material: Cup: plastic; Hinge arm: steel 













Screw Mount 


Press fit 329.09.521 


Tooless 


329.09.541 


-30º Corner application -45º Corner application 

Press fit, Quickmount or Tooless 




Press fit 329.09.520 


Tooless 


329.09.540 



368


DUOMATIC with automatic closing 

30º Corner application 

45º Corner application 



369 




Press fit 329.25.512 


Tooless 


329.25.532 



Press fit 329.25.515 


Tooless 


329.25.535 





DUOMATIC for blind corner applications - Opening angle 94º or 110º 

Blind corner application with mounting plate 


For standard blind corners, opening angle 94º 

Suitable for all DUOMATIC A and DUOMATIC SM mounting plates 


Screw Mount [329.11.505] 

Press fit [329.11.550] 


Tooless [329.11.590] 




Material: Cup: plastic Hinge arm: zinc die-cast 

Colour: nickel-plated 

Cup attachment: screw mount, press fit, quickmount, tooless 

Mounting door to cabinet: slide on with DUOMATIC A mounting plates or clip on attachment 


Adjusting facility: Lateral adjusting continously from -1.5 mm to +4.5 mm 





With self closing spring 





Text 

Change 


Mounting plate distance 0 mm 

3 




E at least: 

With DUOMATIC A = 61 mm 

With DUOMATIC SM = 70 mm 





370


DUOMATIC 

For small blind corners, opening angle 94º For large blind corners, opening angle 110º 

• ONLY suitable for DUOMATIC A mounting plates with drilling 

28 x 32 mm 



Press fit 329.34.510 


Tooless 


329.34.530 


Mounting plate distance 0 mm Mounting plate distance 9 mm 




371 


• Suitable for all DUOMATIC A and DUOMATIC SM mounting 

plates 



Press fit 329.35.510 


Tooless 


329.35.530 

11+ distance to cup 


Mounting plate distance 0 mm Mounting plate distance 3 mm 


E at least: 

With DUOMATIC A = 61 mm 


With DUOMATIC SM 

with rear eccentric = 74 mm 







DUOMATIC for corner cabinets - Opening angle of first door 70º, for door thicknesses up to 23 mm 



Installation reference 

• Material: Hinge arm: zinc alloy 

Cup: steel 


• Cup mounting: screw mount, press fit, quickmount, tooless 













TAB = 3-6 



Calculations of drilling distance for mounting plates: 

Examples for doors with sharp edges 

Door thickness mm Drilling distance wing mounting plate mm 

Determination of drilling distance with wing mounting plates: 

Drilling distance (X) = 31 - door thickness + 32 

20 27 

16 31 

19 28 

18 29 

Door thickness mm Drilling distance wing mounting plate mm 

Determination of drilling distance with wing mounting plates: 

Drilling distance (X) = 31 - door thickness + 32 

20 43 

16 47 

19 44 

18 45 

Door thickness mm Distance to cup mm Mounting plate distance mm 

Determination of mounting plate height: 

Mounting plate height (H) = 26 - door thickness - tab 

20 5 1 

16 6 4 

19 3 3 

18 

Note 

4 5* (26-18-4+1 adjustment) 

* Mounting plate heights that are not available can be 

achieved by using mounting plates with smaller mounting 

plate height plus lateral adjustment. 



372


DUOMATIC 



Screw Mount [329.19.600] 

Press fit [329.19.610] 



Required space 

Maximum opening 

Drilling distance 



373 

Number 

Change 

Maximum of required space for hinge 

with DUOMATIC A mounting plates 


The maximum required space for the hinge is 52 mm with 

door thicknesses from 16 mm. Increasing the door thickness 

reduces the required space accordingly. 

With DUOMATIC A mounting plates with quick mounting 

system 

The maximum required space for the hinge with door thickness 

16 mm is 64 mm with DUOMATIC mounting plates and 68 mm 

with mounting plates with rear eccentric. Increasing the door 

thickness reduces the required space accordingly. 





DUOMATIC for profile doors up to 40 mm - Opening angle 94º 







Minimum gap 

Minimum gap 


3 4 5 6 7 8 9 10 11 12 13 14 15 

0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.4 1.2 2.2 3.2 















Minimum gap 



thickness mm 3 4 5 6 7 8 9 10 11 12 13 14 15 

20 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.3 0.3 0.3 0.3 0.3 0.3 

21 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.4 0.4 0.4 0.4 0.4 

22 0.7 0.7 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.5 0.5 0.5 

23 0.8 0.8 0.8 0.8 0.8 0.8 0.7 0.7 0.7 0.7 0.7 0.7 0.7 

24 1.0 1.0 1.0 0.9 0.9 0.9 0.9 0.9 0.9 0.9 0.9 0.8 0.8 

25 1.2 1.2 1.2 1.1 1.1 1.1 1.1 1.1 1.0 1.0 1.0 1.0 1.0 

26 1.4 1.4 1.4 1.3 1.3 1.3 1.3 1.3 1.2 1.2 1.2 1.2 1.2 

27 1.6 1.6 1.6 1.6 1.5 1.5 1.5 1.5 1.4 1.4 1.4 1.4 1.4 

28 1.9 1.9 1.8 1.8 1.8 1.7 1.7 1.7 1.7 1.6 1.6 1.6 1.6 

29 2.2 2.1 2.1 2.1 2.0 2.0 2.0 1.9 1.9 1.9 1.8 1.8 1.8 

30 2.5 2.4 2.4 2.3 2.3 2.2 2.2 2.2 2.1 2.1 2.1 2.0 2.0 

31 2.8 2.7 2.7 2.6 2.6 2.5 2.5 2.4 2.4 2.4 2.3 2.3 2.3 

32 3.1 3.0 3.0 2.9 2.9 2.8 2.8 2.7 2.7 2.6 2.6 2.6 2.6 

33 3.5 3.4 3.3 3.3 3.2 3.1 3.1 3.0 3.0 2.9 2.9 2.8 2.8 

34 4.1 3.8 3.7 3.6 3.6 3.5 3.4 3.4 3.3 3.3 3.2 3.2 3.2 

35 5.0 4.4 4.1 4.0 3.9 3.8 3.8 3.7 3.6 3.6 3.5 3.5 3.5 

36 6.0 5.3 4.8 4.4 4.3 4.2 4.2 4.1 4.0 3.9 3.8 3.8 3.8 

37 6.9 6.3 5.7 5.2 4.8 4.7 4.6 4.5 4.4 4.3 4.2 4.2 4.2 

38 7.8 7.2 6.6 6.0 5.5 5.1 5.0 4.9 4.8 4.7 4.5 4.5 4.5 

39 8.8 8.1 7.5 6.9 6.4 5.9 5.5 5.4 5.2 5.1 4.9 4.9 4.9 

40 9.7 9.0 8.4 7.8 7.3 6.8 6.3 6.0 5.7 5.6 5.4 5.4 5.4 



374


DUOMATIC 






375 





Press fit 


329.05.640 


18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 

3 4 5 6 7 8 9 10 11 12 13 14 15 0 

3 4 5 6 7 8 9 101112131415 3 



12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 

3 4 5 6 7 8 9 10 11 12 13 14 15 6 

3 4 5 6 7 8 9 101112131415 9 





Press fit 


329.05.641 


7 8 9 10 22 23 24 25 26 27 28 29 30 31 32 33 34 

3 4 5 6 7 8 9 10 11 12 13 14 15 0 

3 4 5 6 7 8 9 101112131415 3 



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 

3 4 5 6 7 8 9 10 11 12 13 14 15 6 

3 4 5 6 7 8 9 10 11 12 13 14 15 9 





Press fit 


329.05.642 


-4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 

3 0 

3 4 5 6 3 



-10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 

3 4 5 6 7 8 9 6 

3 4 5 6 7 8 9 10 11 12 9 






DUOMATIC for aluminum frame profiles - Opening angle 105º 









• Cup attachment: clamping (no recess in profile required) 



• Adjusting facility: 3-dimensional (with appropriate mounting plate) 

• The hinge can be mounted to the frame at any position 


Gap 




9 10 11 12 13 14 15 16 17 18 19 20 21 

6 0 

6 3 

6 6 

6 9 



Gap 






0 1 2 3 4 5 6 7 8 9 10 11 12 

6 0 

6 3 

6 6 

6 9 


Full overlay / 

half overlay mounting 

Gap 






4 5 6 7 8 9 10 11 12 13 14 15 16 

6 0 

6 3 

6 6 

6 9 



Gap 






-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 

6 6 

6 9 




376


DUOMATIC for Aluminum Framed Profiles 

Profiles that make up the door are cut 

as required to a mitre of 45º. 

Mount the hinges onto the mounting 

plates and attach to the assembled 

frame. The hinge can now be 

inserted into the profile recess at any 

position. 

Cut the inner decorative profile to a 

45º mitre. 

Decorative profile 

Cat. No. 563.50.511 



377 

Insert the corner connector into the 

profile recess and attach with premounted 

screws. With larger doors 

we recommend using the additional 

corner connector (see inset picture). 

The hinge positions at the same 

distance to the mounting plate that is 

mounted onto the the furniture side. 

Simply push in the decorative profile 

to complete the door. 


Cat. No. 563.50.512 


Assemble three profiles. The glass is 

attached before mounting the fourth 

and last profile. 

Attach the hinge by a 90º turn of the 

eccentric profile. 

On the hinge side the inner decorative 

profile has to be cut accordingly. 

The practical, simple and elegant 

solution for all furniture types is what 

distinguishes the hinges for the 

aluminum glass frame profile system. 





DUOMATIC for Aluminum Profiled Doors 

Accessories 

Corner connector 

With 2 screws 

With 4 screws 

Size: 30 x 30 mm Size: 44 x 44 mm 

Installation 

Cut aluminum frame 

profiles to a 45º mitre. 

Slide in corner connector. 



Tighten both frame 

profiles together clamping 

screws. 

Material: zinc alloy 

For frame height mm Width mm nickel-plated 

Up to 1,200 500 with 2 screws 563.50.021 

1,200-2,500 


600 with 4 screws 563.50.020 

Corner connectors 

• Additional connection for the frame assembly 

Material: steel 

Cat. No. 

galvanized 563.50.530 


Adapter 

• For fold and lift up fittings for 2-piece flaps, front panels 

and special mountings 


Cat. No. 

galvanized 563.50.999 


Aluminum glass frame profile 

• For glass thickness 4 mm with clatter prevention profile, 

glass thickness 5 mm without clatter prevention profile 

Material: aluminum 

Length mm silver-anodized 

3,000 563.50.900 


Note 

Please order clatter prevention profile for glass thickness 

4 mm separately. 


• Clips into aluminum glass frame profile 

Material: plastic 

Length mm grey 

3,000 563.50.511 

Packing: 1 pc. 

Clatter prevention profile 

• Stabilizes 4 mm panes of glass 

• Slides into aluminum frame profile before inserting panes of 

glass 


Length mm transparent 

3,000 563.50.000 




378


DUOMATIC for aluminum frame profiles - Opening angle 105º 

Half overlay mounting with mounting plate 


Full overlay / half overlay mounting 



379 




• Material: Cup; zinc alloy; Hinge arm: steel 


• Cup attachment: screw mount 




Dimensions 

Gap 





Gap 





New 

Item 


Gap 





Gap 





Mounting Screws: 

Self-tapping sheet metal screw for attaching hardware 

to aluminum frame doors. 

Phillips #7 x 1/2", CSK with undercut head. 

Material: steel, zinc-plated 


Cat. No. 

010.94.902 




DUOMATIC for glass and mirror doors - Opening angle 110º 


Outer dimensions 


• Hinge arm: Straight 

Gap 


6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 

7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 0 

10 11 12 13 14 15 16 17 18 19 20 21 22 3 

13 14 15 16 17 18 19 20 21 22 6 

16 17 18 19 20 21 22 9 



Mounting plate distance mm 

-10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 

0 1 2 3 4 5 6 0 

0 1 2 3 4 5 6 7 8 9 3 

0 1 2 3 4 5 6 7 8 9 10 1112 6 

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 9 



Glued 


329.43.500 

Distance to cup 0-22 


1) Attach plate to the glass 

or mirror door with a 

special adhesive. 

2) Mount hinge when plate 

is securely attached. 

3) To mount hinge, position 

cup on plate and then 

turn eccentric. 



• Material: Cup: zinc alloy 

Hinge arm: steel 


• Cup plate: For gluing to the door (no glass drilling required) 

• Mounting door to cabinet: Slide on with DUOMATIC A mounting plates or clip on attachment 










380


DUOMATIC for rebate and profile doors - Opening angle 110º 


Cup dimensions Minimum gap 


Screw Mount Press fit 









381 


• Material: Cup and hinge arm: zinc alloy 


• Cup attachment: screw mount, press fit 

• Mounting door to cabinet: Slide on with DUOMATIC A mounting plates or clip on attachment 


• Adjusting facility: Lateral adjusting continously from -1.5 mm to +4.5 mm 






Minimum 

gap 



16 0.0 0.0 0.0 0.0 0.0 0.0 

18 0.0 0.0 0.0 0.0 0.0 0.0 

20 0.0 0.0 0.0 0.0 0.0 0.0 

22 0.0 0.0 0.0 0.0 0.0 0.0 

24 0.3 0.4 0.5 0.7 11.3 10.3 

26 1.4 16.9 15.9 14.9 13.9 12.9 

28 20.7 19.7 18.7 17.7 16.7 15.7 


thickness mm 9 10 11 12 13 14 15 16 17 18 

16 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 

18 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 

20 0.0 0.0 0.0 0.0 1.4 0.7 0.2 0.0 0.0 0.0 

22 0.0 6.0 5.1 4.1 3.3 2.6 2.0 1.4 1.0 0.7 

24 9.3 8.3 7.3 6.3 5.3 4.5 3.8 3.2 2.7 2.2 

26 11.9 10.9 9.9 8.9 7.9 6.9 5.9 5.0 4.4 3.9 

28 14.7 13.7 12.7 11.7 10.7 9.7 8.7 7.7 6.7 5.7 


• Hinge arm: Straight 



Press fit 


329.26.610 


7 8 9 10 11 12 13 14 15 16 17 18 19 

6 7 8 9 10 11 12 13 14 15 16 17 18 0 

9 10 11 12 13 14 15 16 17 18 3 

12 13 14 15 16 17 18 6 

15 16 17 18 9 



Mounting plate distance mm 

-5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 

3 4 5 6 0 

3 4 5 6 7 8 9 3 

3 4 5 6 7 8 9 10 11 12 6 

3 4 5 6 7 8 9 10 11 12 13 14 15 9 






Duomatic SM Mounting Plates with clip mount system 

• Material: zinc die-cast 


• Adjusting options: height and depth adjustment using eccentric 

Screw mount 

for use with wood screws 

Screw mount 

with pre-mounted Euro screws 

Press fit 

with pre-mounted dowels 

Screw mount 

for mounting with wood screws 

Screw mount 

for mounting with Euro screws 








Distance D mm Cat. No. 

0 329.67.040 

2 329.67.042 

3 329.67.043 

6 329.67.046 



Screw length 11 mm 

0 329.67.000 

2 329.67.002 

3 329.67.003 

6 329.67.006 



0 329.67.010 

2 329.67.012 

3 329.67.013 

6 329.67.016 



0 329.68.000 

2 329.68.002 

3 329.68.003 

6 329.68.006 



0 329.69.010 

2 329.69.012 

3 329.69.013 

6 329.69.016 




382






Screw mount 


Screw mount 


and spreading dowels 

Image 

Change 

Press fit 

with pre-mounted special screws 

Image 

Change 



383 






0 329.71.500 

2 329.71.502 

3 329.71.503 

6 329.71.506 




0 329.71.510 

2 329.71.512 

3 329.71.513 

6 329.71.516 




0 329.71.520 

2 329.71.522 

3 329.71.523 

6 329.71.526 







• Adjusting options: depth adjustment using eccentric 

height adjustment ±2 mm via slot 

Screw mount 


Press fit 



Screw mount 


• Adjusting options: depth adjustment using eccentric 

height adjustment ±2 mm via slot 

Screw mount 


Screw mount 





Drilling dimensions Material: steel 





Distance D mm nickel-plated 

0 329.62.520 

3 329.62.557 

6 329.62.682 




3 329.73.533 





3 329.85.043 


Material: zinc, die-cast 


0 329.73.600 

6 329.73.606 

9 329.73.608 

12 329.73.609 





0 329.63.522 

6 329.63.787 

9 329.63.796 

12 329.85.032 




384


Duomatic Face Frame Mounting Plates with Clip Mount System 

Face frame wing mounting plates, 

screw-mounted 

• Spring lever 

Face frame wing mounting plates, screw-mounted 


Face frame wing mounting plates, screw-mounted 




385 

Vertical & depth adjustments made with Pozi drive #2 

Adjust vertically ± 2 mm 

by turning cam. 

Adjust depth + 2.8/– 0.5 mm 

by turning cam. 

10 

Face frame 

Hole 

pattern 

10 

Face frame 

10 

Face frame 

Face frame mounting bracket, screw- mounted for inset application 


• 2 cam adjustment 

Hole 

pattern 

10 

Face frame 

32 48 

48 

32 

48 

48 

15 

24 

48 

Dimensions for 

attachment to 

Face frame 

Vertical adjustment 



Face frame 

Wing mounting 

plate 

Side or 

center 

panel 

Flat Head 

#4 

Reinforcement Type nickel-plated 

1 mm 3 329.64.631 

4 mm 6 329.64.640 


Vertical adjustment 


Pan Head 

#8 


1 mm 3 329.64.531 

4 mm 6 329.64.540 


Independent vertical adjustment 



1 mm 3 329.64.551 

4 mm 6 329.64.554 


Independent vertical adjustment 


Flat Head 

#8 

Pan Head 

#8 


5 mm 11 329.67.030 


Raised flat head screws pages 309–310 

Pan head screws pages 304–305 





Duomatic A Mounting Plates with slide on system 

• Material: steel 



Screw mount 


Screw mount 



Screw mount 








0 329.80.528 

3 329.80.555 

6 329.80.582 

9 329.80.699 




0 329.80.700 

3 329.80.703 

6 329.80.706 

9 329.80.709 




0 329.81.525 

3 329.81.552 

6 329.81.589 

9 329.81.590 




386


Duomatic A Mounting Plates with clip mount system 




Mounting plate for screw mounting 


Mounting plate for screw mounting 


Screw mount 


Screw mount 




387 







0 329.80.626 

3 329.80.653 

6 329.80.680 




0 329.81.721 

3 329.81.758 

6 329.84.006 

9 329.81.785 





Cat. No. 

329.84.110 

Cat. No. 

329.84.130 

Note 

The drilling can differ slightly depending on the corner application 

and should be determined by means of test mounting 





DUOMATIC with PUSH system for opening without handle - Opening angle 110º die-cast 


Minimum gap 

Minimum 

gap 



16 0.5 0.5 0.5 0.5 

17 0.7 0.7 0.7 0.7 

18 0.9 0.9 0.9 0.9 

19 1.2 1.2 1.2 1.2 

20 1.5 1.5 1.5 1.5 

21 1.8 1.8 1.8 1.8 

22 2.4 2.1 2.1 2.1 

23 3.7 2.7 2.6 2.5 

24 5.1 4.1 3.1 3.0 

25 6.5 5.5 4.1 3.5 

26 7.8 6.8 5.4 4.4 





• Cup mounting: screw mount, press fit 








Drilling dimensions for cup 

attachment 

Screw Mounting Press fit 








between door and 

side panel 

Minimum 

distance 




16 0.0 0.0 1.1 2.0 

17 0.0 0.0 1.3 2.3 

18 0.0 0.3 1.6 2.5 

19 0.0 0.6 1.8 2.8 

20 0.2 0.9 2.1 3.1 

21 0.5 1.2 2.3 3.3 

22 0.8 1.4 2.6 3.6 

23 1.1 1.7 2.9 3.8 

24 1.4 2.0 3.1 4.1 

25 1.7 2.3 3.4 4.3 

26 1.9 2.6 3.6 4.6 

Rounding off the edge of door reduces the given values 



388


DUOMATIC with PUSH system 


Hinge arm: Straight (crank 0 mm) 




389 

Gap 



Press fit 


329.17.810 


9 10 11 12 13 14 15 16 17 18 19 20 21 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 9 



Gap 





Press fit 329.17.812 



0 1 2 3 4 5 6 7 8 9 10 11 12 

3 4 5 6 0 

3 4 5 6 3 

3 4 5 6 6 

3 4 5 6 9 





Gap 

Hinge arm: High cranked (crank 17 mm) 




Press fit 329.17.813 



-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 

3 4 5 

0 

3 

3 4 5 6 6 

3 4 5 6 9 





Duomatic PUSH door opening system - For opening without handle 



• Material: plastic 

• Mounting: side, cabinet top or cabinet base 

• Installation: screw mount or glue on 

PUSH Door Catch 

Screw mount 

with positioning aid 

Colour Cat. No. 

grey 329.44.500 

Packing: 50 pcs. (includes 2 side cover caps and screws) 

Without positioning aid 


grey 329.44.501 


Glue on 



grey 329.44.520 


Mounting instructions: 

1) The surface where the catch is going to be installed has to be 

cleaned and degreased using cleaning agents containing 

acetone. 

2) Remove protective foil from double-sided adhesive tape. 

3) Fix catch and press on firmly for approximately 1 minute. 

4) Do not use the catch for the first 12 hours. 



390


DUOMATIC locking part for PUSH door catch - For wooden doors 

Press fit, for overlay doors 


grey 


329.44.532 

Screw mount, for inset doors 



grey 


329.44.530 

without positioning aid 


grey 


329.44.531 



391 

Installation for overlay doors 

Locking part Door catch 

Installation for inset doors 

Locking part Door catch 



The use of 2 PUSH door catches is recommended for doors that are 

more than 1,600 mm in height. 




SMOVE Door Dampening System 

For mounting in drilled hole without adapter. 

Ø10 

(3/8”) 

Installation into cabinet top or base. 

50 

(1 15/16”) 

Text 

Material: plastic – [Light Resistance] Change 


grey 356.33.509 

cream-white 356.11.400 


1 

(1/16”) 

Installation: 

• Insert SMOVE into middle of top panel or base 

• For doors above a height of 1,600 mm (63”) or doors with aluminum 

and wooden frames it may be required to use 2 SMOVES, which 

have to be inserted into top panel or base 

Ø10 

(3/8”) 

50 

(1 15/16”) 

Text 

Material: plastic – [Medium Resistance] Change 


grey 356.33.510 



1 

(1/16”) 

Installed in side panels opposite the hinge side. 



Installation: 

• Insert SMOVE into side panel of furniture opposite the hinge side. 

• Performance is optimised by its central position in the furniture panel. 

• It is recommended for doors from 450 to 600 mm (17 11/16” to 

23 5/8”) wide. For doors above a height of 1,600 mm (63”) or 

doors with aluminum and wooden frames it may be required to use 

2 SMOVES, which have to be inserted into top or bottom side panel 

of the furniture. 

Installation into cabinet top or base next to hinge side. 

Installation: 

• Insert SMOVE into top panel or base next to hinge side 

• A drilling distance of 27 mm (1 1/16”) from the inside is recommended 

• For doors above a height of 1,600 mm (63”) it may be required to use 

2 SMOVES, which have to be inserted into top panel or base 

Assembly test block 

Ø10 

(3/8”) 

50 

(1 15/16”) 

392 

1 

(1/16”) 

Text 

Material: plastic – [Heavy Resistance] Change 


grey 356.11.520 



New 

Item 



orange 356.33.430 


10 mm twist drill bit HSS 


Cat. No. 

001.41.293 



Inches are approximate

Adapters 

SMOVE Door Dampening System Adapter for screw mounting or press fitting 

Cross Adapter 

• With positioning aid 



grey 356.11.560 



Double Adapter 




grey 356.11.580 





393 

Flat Head 

#8 

Adapter for sticking on 

Cross Adapter 

• Without positioning aid 




grey 356.11.562 


Adapter 

• Sticks on with double sided adhesive tape or 

screw mounts. 




grey 356.11.532 



Flat head screws pages 302–304 





DUOMATIC concealed hinge accessories 

Hinge arm cover caps 

Cup cover cap 

Opening angle restraint 




For concealed hinges Cat. No. 

Opening angle 105º 329.32.500 

Angle hinges 

Blind corner hinges 

Corner hinges 


• Area of application: suitablw for cups with drilling Ø 35 mm 

• Material: steel 



Cat. No. 

329.32.530 

For concealed hinges Cat. No. 

1 Plastic white 

With 165º hinges it restricts the opening to 120º 329.24.520 

With 155º hinges it restricts the opening to 125º 


With 155º hinges it restricts the opening to 115º 

2 Steel nickel-plated 


Only suitable for hinges with 35 mm cup diameter 




394


DUOMATIC concealed hinge accessories 

Cup cover caps for glass door hinges 

• Material: plastic 




395 


black 329.22.310 

black 329.22.320 

black matt 329.22.330 

black matt 329.22.340 

white 329.22.710 

white 329.22.720 

gold coloured polished 329.22.830 





gold coloured matt 329.22.810 

gold coloured matt 329.22.820 

chrome-plated polished 329.22.210 

chrome-plated polished 329.22.220 

silver coloured matt 329.22.910 

silver coloured matt 329.22.920 





300 - Grass 

Which hinge type? 

Sample 

• Opening angle 110° 

• Side panel thickness: 19 mm 

• Door thickness: 19 mm 

• Tab spacing e.g. 4 mm (variable) 

• Gap e.g. 5 mm (variable) 

The minimum gap is determined by the door 

thickness and the cup spacing. 

Answer - here 1.8 mm - can be found in 

the table on each hinge page. 

Example: minimum gap table of 110° hinge 

Minimum gap F: The required minimum gap depends on the given door thickness and cup spacing (Tab). 

Door thickness in mm 16 17 18 19 20 21 

Tab in mm 3.0 1.1 1.3 1.6 1.9 3.6 5.4 

3.5 1.1 1.3 1.6 1.9 3.1 4.9 

4.0 1.1 1.3 1.6 1.8 2.6 4.4 

4.5 1.0 1.3 1.5 1.8 2.1 3.9 

The above dimensions (or greater as for example 5 mm) should be used for gap F. 

Sample Calculations 

How many hinges per door? 

Hinge Type 14 

Side panel mounting 

for overlay doors 

Tab 

Door 

Hinge Type 6 

Center panel/twin mounting 

overlay doors 

Center 

panel 

Door Door 

There is no general answer to the question of how many hinges to use per door. 

The deciding factors here are the dimensions of the doors and the resulting 

weight. In case of doubt (for doors with mirrors or exceptionally wide doors) a 

trial mounting is recommended. Avoid doors which are wider than they are tall. 

For normal doors made of conventional materials, the adjacent table can be 

used to aid your decision. If in doubt, allow for an extra hinge. 

Tab 

Door 

width 

(mm) 


2500 

2000 

1500 

1000 

500 

Door height 

in mm 

22 

7.1 

6.6 

6.1 

5.6 

Hinge Type -2 


for inset doors 

(A) Full Overlay (C) Inset 

(B) Half Overlay or 

Twin Mounting 

16 mm (5/8") Hinge Mounting Tab Total 

Material Type Plate Overlay 

Full overlay (A) 14 - 4 + 5 = 15 

Half overlay (B) 6 - 4 + 5 = 7 

Inset (C) -2 - 1 + 3 = 0 

If there is no mounting plate with the required reinforcement, then the tab or gap must be altered. 

Side 

Tab 

Weight approx. (in kg.) 

4 - 5 6 - 9 10 - 15 16 - 22 

500 500 500 500 


2 3 4 5 

No. of hinges 

Door 



Full overlay (A) 14 - 1 + 4 = 17 

Half overlay (B) 6 - 1 + 4 = 9 

Inset (C) -2 - 1 + 3 = 0 



396


300 – Grass 

• Snap-on the side panel, three-way adjustment 

• Cup depth of only 10.5 mm allows for use in thin or framed doors 

• Closing spring made of hardened steel to ensure long service life 

• Vertical cam adjustment on wing base plate 

Optional: Trim caps for hinge arm can be printed with company logo 

if desired. (minimum order quantity of 5,000) 

Diagram showing rapid 

assembly system 



397 

45° 

Adjustment facilities 

The door 

should be 

positioned 

at an angle of 

45° 

Lateral adjustment ± 2 mm Front-to-back 

adjustment ± 2 mm 

Vertical adjustment ± 2 mm 






373/374/375 – Grass 

• Snap-on feature 

• Door thickness: 13 to 24 mm 

• Tab 3 - 7 mm 

• Side panel thickness from 16 mm 

• Three-way adjustment 

• Self-closing 

Opening angle: 

Screw-mount, 42/11 


Press-fit, 42/11 


Trim caps for hinge arm Material: steel 

B 

A 

42 

Depth 10.8 

42 

Depth 10.8 

Raised flat head wood screws pages 309–310 

C 

8 

11 

11 

Tab 

35 

Tab 

35 



Mounting Hinge arm Type nickel-plated 

Full 

overlay 

Straight 14 348.00.500 348.00.700 

Half 

overlay 

8 mm 

crank 6 348.00.501 

Inset 

16 mm 

crank -2* 348.00.502 

Packing: 50 pcs. 300 pcs. 

* for hinge type -2 the opening angle is only 100° 


Full 

overlay 

Straight 14 348.00.510 348.00.710 

Half 

overlay 

8 mm 

crank 

6 348.00.511 

Inset 

16 mm 

crank -2* 348.00.512 


* for hinge type -2 the opening angle is only 100° 

Mounting Hinge arm nickel-plated matt 

Full 

overlay 


Straight 

348.78.700 

Hinge arm 

crank Dim. A Dim. B Dim. C 

Straight 8.5 19.0 63 

8 mm 16.5 27.0 63 

16 mm 26.9 37.4 65 + door thickness 

Dim. A and B + mounting plate reinforcement. 

Flat Head 

#6 



398


383/384 – Grass 


• Door thickness 16 to 24 mm 






399 


Trim caps for hinge arm 





B 

A 



Full overlay 

Straight 14 348.01.500 

Half overlay 

8 mm crank 6 348.01.501 



Full overlay 

Straight 14 348.01.510 

Half overlay 

8 mm crank 6 348.01.511 



Minimum gap F: 

the required minimum gap depends on the given door thickness and cup spacing (Tab). 

Door thickness in mm 16 17 18 19 20 21 22 

Tab in mm 3.0 0.9 1.2 1.5 1.9 3.6 5.3 7.1 

5.0 0.9 1.1 1.4 1.6 2.0 3.3 5.1 

The above dimensions (or greater) should be used for gap F. 

The values in the above table are based on a door corner radius of 1 mm. 

42 

Depth 12.7 

42 

Depth 12.7 

8 

11 

11 

Tab 

35 

Tab 

35 


Full overlay 

Straight 348.79.706 


(Can be printed with company logo with min. order of 5,000 pcs.) 

Hinge arm 


Straight 9.9 22 63 

8 mm 18.2 27.7 63 

Dim. A and B + mounting plate reinforcement 


C 

Flat Head 

#6 





393/394 – Wide Angle Hinge – Grass 





• Self closing 

• Zero protrusion in full overlay application allows for pull-outs 








Full overlay 

Straight 14 348.03.600 

Half overlay 

8 mm crank 6 348.03.601 





Full overlay 

Straight 14 348.03.610 

Half overlay 

8 mm crank 6 348.03.611 



the required minimum gap depends on the given door thickness and cup spacing (Tab). 

Door thickness in mm 16 17 18 19 20 

Tab in mm 3.0 

4.0 

5.0 

6.0 

7.0 

8.0 

9.0 

10.0 

In the case of double 

doors which close 

against each other, a 

minimum gap must be 

observed depending 

on the door width. 



42 

Depth 10.8 

42 

Depth 10.8 

Door overlay by opening the door is 0 mm on the side of the hinge. 

Door 

8 

11 

11 

Center 

panel 

Gap Door 

B 

A 

Tab 

35 

Tab 

35 

Inset mounting can be obtained by using a mounting plate 

with 9.3 mm reinforcement, type 9, in connection with a hinge with 

8 mm crank, type 6. 

Door thickness Door width Gap 

up to 

20 mm 

C 

300 mm 0.7 mm 

400 mm 0.6 mm 

500 mm 0.5 mm 

600 mm 0.4 mm 

Flat Head 

#6 

Hinge arm 


Straight -8.3 46.2 63 

8 mm -0.3 54.2 63 

Dim. A and B + mounting plate reinforcement 



400


343 – Diagonal Corner Hinge – Grass 

• Angle hinges with snap-on feature 


• Tab 3 - 7 mm 



• Suitable mounting plates can be found on pages 404–406 

Door open 

Door 




401 

Ø35 

Door 


B 

Side panel 

42 

Depth 10.8 

42 

Door closed 

16 

2 

Tab 3.5 

Depth 10.8 

2 

C 

16 

8 

11 

11 

37 

2 

63 

Tab 

35 

Tab 

35 


Material: Cup: steel 

Hinge arm: zinc die-cast 


Mounting Hinge arm nickel-plated 

Overlay With 45° angle 348.06.501 






Overlay With 45° angle 348.06.511 


4.3 

16 

16 

A 



Side panel With 45º angle 348.78.700 


Door 

Hinge arm Dim. A Dim. B Dim. C 

with 45° angle 35.0 30.7 6.6 

Dimensions based on 4.3 mm mounting 

plate reinforcement. 

Corner cabinet 

Corner hinge 

Flat Head 

#6 






321 – Pie-cut Corner Hinge – Grass 




• Tab 3.5 mm 



19 

90 

25 

42 

Depth 10.8 

42 

Depth 10.8 

90 

4.8 

4.2 

0.5 

0,5 

8 

11 

11 

3.6 with 3.5mm cup 

drilling distance 

19 19 

28.6 

Tab 

35 

Tab 

35 




Pan Head 

#6 

Material: zinc die-cast 


nickel-plated 348.09.600 







Hinge 393 

Hinge 321 



402 

0,5


333 – Blind Corner – Grass 

• Frame-mounting hinges with snap-on feature 

• Door thickness 13 to 24 mm 



Door open 

B 

Door 



403 


C 


Frame-mounting hinge 

Door 

Side panel 

Flanged mounting plate 

type 4, see below 

42 

Depth 10.8 

11 

Press-fit 

see drilling diagram 

on page 45. 

Door closed 

Ø35 

37 

78.5 

Tab 

35 

Gap 

Tab 

min. 

22 

min. 

15 

Rear of 

frame 






Inset With 90° angle 348.04.501 






Inset with 90° angle 348.04.510 


Minimum gap F: the required minimum gap depends on the given 

door thickness and cup spacing (Tab). 

Door thickness in mm 16 17 18 19 20 21 22 

Tab in mm 3.0 0.6 0.8 1.0 1.3 1.6 2.8 4.2 

3.5 0.6 0.8 1.1 1.3 1.6 2.3 3.7 

4.0 0.7 0.8 1.1 1.3 1.6 2.0 3.2 

4.5 0.7 0.8 1.1 1.4 1.7 2.0 2.7 

5.0 0.7 0.9 1.1 1.4 1.7 2.1 2.5 



32 

Trim caps, Cat. No. 348.78.700, see page 401 

4.3 

Hinge arm Dim. B Dim. C 

With 90° angle 21.0 43.0 

Flat Head 

#8 

• With vertical adjustment via slots ± 2mm 

Flat Head 

#6 

Flat Head 

#8 

Reinforcement VP type Cat. No. 

4.3 mm 


4 348.21.624 







Mounting Plates for 300 Series – Grass 

Mounting plates, two-part 

Flanged mounting plates, two-part 

Mounting plates, two-part, inline 

Door Side 

panel 

Door Side 

panel 

2.0 

Flanged mounting plates, two-part, 5 mm dowel 


2.0 

Drilling diagram 

37 

Drilling 

diagram 

37 

Ø 5 


17 32 


37 

Ø 5 

32 

32 

32 

32 

32 

Screw-mounted 

Material: zinc die-cast/steel 






1.3 mm 1 348.25.001 

4.3 mm 4 348.25.004 

9.3 mm 9 348.25.009 


Screw-mounted 

Complete with pre-assembled mounting screws. 

Vertical adjustment via cam ± 2mm. 


1.3 mm 1 348.25.011 

4.3 mm 4 348.25.014 

9.3 mm 9 348.25.019 


Screw-hole offset = distance between door and 

side panel 2.0 mm. 

Screw-mounted 

Vertical adjustment via cam ± 2mm. 


1.3 mm 1 348.24.601 

4.3 mm 4 348.24.604 

9.3 mm 9 348.24.609 


Vertical adjustment via cam ± 2mm 



1.3 mm 1 348.25.021 

4.3 mm 4 348.25.024 

9.3 mm 9 348.25.029 


Flat Head 

#8 

Discontinued 

Note: To ensure maximum holding power, all screw 

holes must be utilized in all versions of mounting plates. 



404



Face frame mounting plate 





405 


• Vertical adjustment via cam ± 2mm 


Reinforcement Type Cat. No. 

2.8 mm 


3 348.26.012 

• Vertical adjustment via slots ± 2mm 



2.6 mm 


3 348.26.001 



Flat Head 

#8 


4.3 mm 4 348.26.004 

7.3 mm 


7 348.26.009 

Note: To ensure maximum holding power, all screw 

holes must be utilized in all versions of mounting plates. 







Flanged mounting plates 




37 

Drilling 

diagram 

37 

Door 

Ø 5 

Side 

panel 

32 

32 

32 

2.0 




• Complete with pre-assembled mounting screws 

• Screw-mounted 


Flat Head 

#8 


1.3 mm 1 348.21.601 

4.3 mm 


4 348.21.604 


• Complete with pre-assembled mounting screws 




1.3 mm 


1 348.21.611 



406


300 Accessories – Grass 

Pozi-drive #2 Screwdriver 

Spacer Wedge 

Mounting Plate Spacer 



407 

B6 

Material: steel, plastic 





• Pozi-drive screwdriver must be used when 

adjusting hinges 

Cat. No. 

006.33.002 


Degree Cat. No. 

5º 348.23.640 

10º 348.23.641 


• Height: 2 mm 

Cat. No. 

348.23.650 





3000/4000 Snap-on Hinges – Grass 


Sample: 

• Opening angle 110° 

• Side panel thickness: 19 mm 

• Door thickness: 19 mm 

• Tab 4 mm (variable) 

• Gap e.g. 5 mm (variable) 

The minimum gap is determined by the door 

thickness and the cup spacing. 

Answer - here 1.8 mm - can be found in the 

table on each hinge page. 

Example: Minimum gap table of 110° hinge 

Minimum gap F: the required minimum gap depends on the given door thickness and hinge cup spacing (Tab). 

Door thickness in mm 16 17 18 19 

Tab in mm 3.0 1.1 1.3 1.6 1.9 

3.5 1.1 1.3 1.6 1.9 

4.0 1.1 1.3 1.6 1.8 

4.5 1.0 1.3 1.5 1.8 

The above dimensions (or greater, e.g. 5 mm) should be used for gap F. 


Hinge Type 14 



Tab 


Door 

There is no general answer to the question of how many hinges to use 

per door. The deciding factors here are the dimensions of the doors 

and the resulting weight. In case of doubt (for doors with mirrors or 

exceptionally wide doors) a trial mounting is recommended. Avoid 

doors which are wider than they are tall. For normal doors made of 

conventional materials, the adjacent table can be used to aid your 

decision. If in doubt, allow for an extra hinge. 

20 

3.6 

3.1 

2.6 

2.1 

Hinge Type 6 


overlay doors 

Center 

panel 

Door Door 

Tab 

(78 3/4") 2000 

(59 1/16") 1500 

(39 3/8") 1000 

(19 11/16") 500 


21 

5.4 

4.9 

4.4 

3.9 

Door height 

in mm 

(Inches) 

22 

7.1 

6.6 

6.1 

5.6 

Hinge Type -2 





Twin Mounting 



Full overlay (A) 14 - 4 + 5 = 15 

Half overlay (B) 6 - 4 + 5 = 7 

Inset (C) -2 - 1 + 3 = 0 

If there is no mounting plate with the required reinforcement, then the tab or gap must be altered. 

Side 

Tab 

Door 

width 

(mm) 

Weight approx. (in kg) 

4 - 5 6 - 9 10 - 15 16 - 22 

500 500 500 500 

(98 7/16") 2500 

2 3 4 5 


Door 



Full overlay (A) 14 - 1 + 4 = 17 

Half overlay (B) 6 - 1 + 4 = 9 

Inset (C) -2 - 1 + 3 = 0 



408


3000 Series Snap-on Hinges – Grass 

• Snap-on system allows hinge arm adjustment in all 3 directions 

• Functional parts made of hardened steel - ensures long-term durability 

• 3-way adjustment allows repeated disassembly and assembly without having to re-adjust 

• Optional trim caps can be printed with company logo. Please order separately 

• Wide range of hinges and baseplates available to accommodate most applications 

• Sturdy insertion hooks ensure stability of the hinge arm on the baseplate, eliminating any play 

Diagram showing 

snap-on mounting. 



409 

Lateral Adjustment ± 2 mm Front-to-back 

Adjustment ± 2 mm 

Vertical Adjustment ± 2 mm 






4000 Series Twist Lock Snap-on Hinges – Grass 

Twist Lock 

• Requires no tools for hinge assembly 

• Cup drilling is a single 35 mm hole 

• Allows for cabinet doors to be shipped flat, eliminating shipping damage 

• Clean lines, classic design 

• Functional parts made of hardened steel - ensures long term durability 

• Three-way adjustment allows repeated disassembly and assembly 

without having to re-adjust 

35 

cup distance 



Suggestions when using 3000 Series Snap-on 

and 4000 Series Twist Lock hinges: 

• Use a Pozi drive #2 screwdriver when adjusting hinges 

• Attach baseplate using all available screw holes 

• Keep hinges as close to top and bottom of door as possible 

Maximum recommended distance 75 mm (3") from end of door 

• Avoid doors which are wider than they are tall 



410










411 


Twist Lock cup included with Twist Lock 

hinges. For hardwood applications please 

order separately. See page 425. 


42 

Depth 12.7 

42 

Depth 12.7 

Depth 12.7 

8 

11 

11 

Tab 

35 

Tab 

35 



Minimum gap F: required minimum gap depends on the given door thickness and cup spacing (Tab). 


Tab in mm 3.0 0.9 1.2 1.5 1.7 2.1 2.4 

3.5 0.9 1.2 1.4 1.7 2.0 2.4 

4.0 0.9 1.2 1.4 1.7 2.0 2.4 

4.5 0.9 1.1 1.4 1.7 2.0 2.3 

5.0 0.9 1.1 1.4 1.6 2.0 2.3 

5.5 0.9 1.1 1.4 1.6 1.9 2.3 

6.0 0.9 1.1 1.4 1.6 1.9 2.2 

6.5 0.9 1.1 1.3 1.6 1.9 2.2 

7.0 0.9 1.1 1.3 1.6 1.8 2.2 





Full 

overlay 

Straight 14 348.77.506 348.77.706 

Half 

overlay 

8 mm 

crank 6 348.77.515 





Full 

overlay 

Straight 14 348.77.551 348.77.751 

Half 

overlay 

8 mm 

crank 6 348.77.560 


Tab 

Twist Lock 



35 

Full 

overlay 

Straight 14 348.57.602 

Half 

overlay 


8 mm 

crank 6 348.57.611 


Hinge arm black 

348.79.706 

Straight 

348.79.304 

8 mm 348.79.715 

crank 348.79.313 

Packing: 50 pcs. (Can be printed with company logo. Minimum order 

of 5,000 pcs.) 


B 

A 

Hinge arm 


Straight 9.1 22.0 67 

8 mm 17.0 27.7 67 

C 

Flat Head 

#6 










• Self closing 


Twist Lock cup included with 

Twist Lock hinges. For hardwood 

applications please order separately. 

See page 425. 



42 

Depth 12.7 

42 

Depth 12.7 

8 

Depth 12.7 

11 

11 

Tab 

35 

Tab 

35 

Tab 

35 


Material: Cup: zinc die-cast 


Mounting 

Inset 





Mounting 

Inset 


Twist Lock 



Mounting 

Inset 



Minimum gap values F: 

the required minimum gap depends upon the given door thickness and cup spacing (Tab). 

Door thickness in mm 16 17 18 19 

Tab in mm 3.0 0.9 1.2 1.5 1.7 

3.5 0.9 1.2 1.4 1.7 

4.0 0.9 1.2 1.4 1.7 

4.5 0.9 1.1 1.4 1.7 

5.0 0.9 1.1 1.4 1.6 



Hinge arm 

Hinge arm Type 


B 

A 

16 mm 

crank 

16 mm 

crank 


Mounting Hinge arm black 

Inset 

348.79.724 

348.79.322 

Packing: 50 pcs. (Can be printed with company logo. Minimum 

order of 5,000 pcs.) 

-2 

Hinge arm Type 

16 mm 

crank 

Type 

-2 

-2 

Hinge arm 


Inset 24.6 37.9 69+ door thickness 

C 

Flat Head 

#6 

nickel-plated 

348.77.622 

nickel-plated 

348.77.677 

nickel-plated 

348.57.620 



412


3803/4804 Snap-on Hinges Airmatic – Grass 



413 


2 

4 

2 

4 

5 

3 

Ø 

5 

3 

Ø 

11 

32 21 

11 

Ø8 

32 21 

12.8 

12.8 






Screw-mount 



Mounting 

Full 

overlay 

Half 

overlay 


Press-fit, dowel 



Mounting 

Full 

overlay 

Half 

overlay 



nickel-plated 

348.71.620 

348.71.621 

nickel-plated 

348.71.670 

348.71.671 






Snap-on feature 

Door thickness: 16 to 22 mm 

Side panel thickness from 16 mm 

Three-way adjustment 

Self closing 


Twist Lock cup included with Twist Lock 

hinges. For hardwood applications please 

order separately. See page 425. 


42 

Depth 12.7 

42 

Depth 12.7 

8 

11 

11 

35 

35 



Mounting Hinge arm 

Type 

Full 

overlay 

Half 

overlay 

Straight 

8 mm 

crank 



Mounting Hinge arm Type 

Full 

overlay 

Straight 14 

8 mm 

crank 

Twist Lock 


Mounting Hinge arm Type 

Full 

overlay 

Straight 14 



nickel-plated 


Half 

overlay 

14 

6 

Hinge arm 

crank 

Straight 

8 mm 

348.71.504 348.71.704 

348.71.513 



Hinge arm 

Straight 

Half 

overlay 

Minimum gap F: required minimum gap depends on the given door thickness and cup spacing (Tab). 

Door thickness in mm 

Tab in mm 3.0 

3.5 

4.0 

4.5 

16 

1.1 

1.1 

1.1 

1.0 

17 

1.3 

1.3 

1.3 

1.3 

Depth 12.7 

18 

1.6 

1.6 

1.6 

1.5 




19 

1.9 

1.9 

1.8 

1.8 

Tab 

Tab 

Tab 

35 

Half 

overlay 


6 

Dim. A 

9.9 

18.2 

nickel-plated 

348.71.559 [348.71.759] 

348.71.568 

black 

348.79.706 

348.79.304 

348.79.715 

348.79.313 



20 

3.6 

3.1 

2.6 

2.1 

21 

5.4 

4.9 

4.4 

3.9 

8 mm 

crank 

22 

7.1 

6.6 

6.1 

5.6 

6 

B 

A 

Dim. B 

22.0 

27.7 

Flat Head 

#6 

nickel-plated 

348.51.600 

348.51.619 

C 

Dim. C 

67 

67 



414 

Number 

Change







• Wide angle 

• Zero protrusion in full overlay application allows for pull-out 



415 


Twist Lock cup included with 

Twist Lock hinges. For hardwood 

applications please order separately. 

See page 425. 

135º Angle Reduction Clip 

• For 165º hinge 


Minimum gap F: the required minimum gap depends on the given door thickness and cup spacing (Tab). 


Tab in mm 3.0 Door overlay by opening the door is 0 mm 

4.0 

5.0 

6.0 

7.0 

8.0 

9.0 

10.0 

In the case of double 

doors which close against 

each other, the minimum 

gap shall depend on the 

door width: 

42 

Depth 12.7 

42 

Depth 12.7 

Depth 12.7 

Door 

The above dimensions (or greater) should be used for gap F. The values in the above table are based 

on a door corner radius of 1 mm. 

F 

Gap 

8 

11 

11 

Center 

panel 

Door 

Tab 

35 

Tab 

35 

Tab 

35 






Hinge type 

Full 

overlay 

Straight 14 

Half 

overlay 





8 mm crank 6 


Hinge type 

Full 

overlay 

Straight 14 

Half 

overlay 



Door thickness Door width Gap 

up to 

22 mm 

Twist Lock 



300 mm 1.4 mm 

400 mm 1.2 mm 

500 mm 1.0 mm 

600 mm 0.8 mm 

8 mm crank 


Hinge type 

Full 

overlay 

Half 

overlay 


Straight 

8 mm crank 


B 

A 

Hinge arm 

crank 

Straight 

8 mm 

6 

14 

6 

Dim. A 

-8.3 

-3.2 

nickel-plated 

348.73.606 

348.73.615 

nickel-plated 

348.73.651 

348.73.660 

nickel-plated 

348.53.604 

348.53.613 

Cat. No. 

348.73.690 

Dim. B 

46.0 

54.2 

C 

Flat Head 

#6 

Dim. C 

67.4 

67.4 





3606/3608 Snap-on Hinges for Thick Doors – Grass 









42 

Depth 12.7 

42 

Depth 12.7 

8 

11 

11 

Tab 3-4.5 

35 

Tab 

35 

B 

A 





Type 

Full 

overlay 

Inset 




C 

Straight 


14 

With 16 mm crank -2 





Type 

Full 

overlay 

Straight 14 

Inset 

With 16 mm crank -2 


Hinge arm 

16 mm 

crank+ 

straight 

Minimum gap F: the required minimum gap depends on the given door thickness and cup spacing (Tab). 


Tab in mm 4.5 

Profile Door 

Profile 

25° 

16-25 

0.0 

Door 

26 

0.1 

35 

25 

27 

0.1 

28 

0.2 

29 

1.3 


30 

2.4 

Door thickness in the case of 1 mm door corner radius: max. 25 mm 

Door thickness with profiles (see above diagram): up to 35 mm 

50 

32 

31 

3.4 

Note: Baseplate setback is 50 mm instead 

of 37 mm for inset mounting only. 

Hinge arm 

crank 

Straight 

16 mm 

Dim. A 

17 

32.4 

nickel-plated 

Dim. B 

28 

43.5 

348.67.600 

348.67.620 

nickel-plated 

348.67.650 

348.67.670 

black 

348.79.724 

348.79.322 



32 

4.5 

33 

5.6 

34 

6.7 

35 

7.8 

Flat Head 

#6 

Dim. C 

80 

75 



416


3403/4403 Diagonal Corner Hinge – Grass 

• Corner hinges with rapid assembly system 

• Door thickness 16 - 22 mm 


• Automatic closing spring 

• Suitable mounting plates found on pages 423–424 


Door 



417 



Corner hinge 

Door thickness 

in mm 

16 

17 

18 

19 

20 

21 

22 

42 

Depth 12.7 

42 

Depth 12.7 

Depth 12.7 

Minimum gap 

in mm 

0.5 

0.6 

0.7 

0.9 

1.1 

1.3 

1.5 

The values in the above table are 

based on rectangular doors. 

8 

11 

11 

Door open 

Door 

Tab 

35 

Tab 

35 

Tab 

35 

Door 








Twist Lock 



B 

Double 

gap 

2 mm 

gap 

Side panel 

C 

16 

Door 

Cup 

spacing 



Overlay With 30° angle 

348.68.614 

With 45° angle 

348.68.605 


348.68.641 

Mounting 


Mounting 





Hinge arm 




Hinge arm 



Side panel 

mounting 

for 45° angle 


16 

32 

2 

80.5 

Side panel 

nickel-plated 

348.68.671 

348.68.673 

348.68.675 

nickel-plated 

348.48.612 

348.48.603 

348.48.649 

nickel-coloured matt 

Packing: 50 pcs. (Can be printed with company logo. 

Minimum order of 5,000 pcs.) 

Door closed 

348.79.706 

16 

16 

A 

Mounting 

plate 4.3 




3203 Snap-on Hinges – Negative 45º – Grass 

45° corner hinge with snap-on feature 





Trim caps, for hinge arm 


48 

78.5 

Gap F 

Door overlay 

44.5 


2 

93 

42 

Depth 12.7 

42 

Depth 12.7 

4.3 

1.3 

25.2 

22.2 

8 

11 

11 

3-5 

35 

Tab 

35 




Hinge arm 

With -45° angle 





Hinge arm 

With -45° angle 


Example of inset mounting 



Side panel 

mounting 

for -45° angle 




the required minimum gap depends on the given 

door thickness and cup spacing (Tab). 


Tab in mm 3.0 

up to 5.0 

16 

0.7 

0.6 

17 

0.9 

0.8 

18 

1.1 

1.0 

19 

2.3 

1.3 

20 

4.0 

2.0 

Example of overlay 

Tab in mm 3.0 

Door overlay (in mm) 

1.5 

3.5 

2.0 

4.0 

2.5 

4.5 

3.0 

5.0 

3.5 

The gap depends on the design of the furniture. 

nickel-plated 

348.68.650 

nickel-plated 

348.68.660 

21 

5.7 

3.7 

Flat Head 

#6 

22 

7.5 

5.5 

The above dimensions (or greater) should be used for 

gap F. The values in the above table are based on a 

door corner radius of 1 mm. 

nickel-coloured matt 

348.79.706 

Packing: 50 pcs. (Can be printed with company logo. 

Minimum order of 5,000 pcs.) 



418



3503/3505 Snap-on Hinges for Glass Doors 

Glass door hinge with snap-on system 

• Glass thickness from 3 mm (1/8") to 4 mm (5/32") 



• Mounting screws for the cover plates are packed with the hinges 

• Maximum glass thickness for tempered glass is 4 mm (5/32") 

Cover plates, round 

419 


Cover plates, straight, square 


35 

35 

46 

9 

9 

Tab 

30 

Screw-mounted 

Material: Cup: plastic 



Type 

Full 

overlay 

Inset 


Straight 

With 16 mm crank 


nickel-plated/ 

black 



nickel-plated polished 342.98.176 


black 


342.98.130 


Hinge arm 

Inset 


14 

-2 

nickel-plated 

348.79.706 

348.79.724 

348.75.306 

348.75.324 





black 


342.98.336 

Full 

overlay 

black 

348.79.304 

348.79.322 






3103 Snap-on Hinge for Aluminum Frame Doors – Grass 

Hinges with snap-on feature 




4 

22.2 

Baseplate 1.3 

13 

19 

Space 

65.4 

(3.5) 

minimum reveal 


Recess for 

hinges 

Ø5 


28 

14 

10 

4 

Ø8/80° 

32 +1 

30.2 

Baseplate 9.3 

5 

19 

6,3 

Space 

7 

65.4 

(11.5) 

minimum reveal 

Full overlay mounting Half overlay mounting 

B 

A 

C 

Half overlay 

mounting 

can be obtained by using 

a mounting plate with 

9.3 mm reinforcement. 



Screw-mounted 




Full 

overlay 

straight 14 348.83.910 

Packing: 50 pcs. (includes mounting screws) 

Frame width minimum gap minimum reveal 

19 mm 1.9 mm 0 mm 

20 mm 1.6 mm 0.1 mm 

21 mm 1.5 mm 1.1 mm 

22 mm 1.4 mm 2.1 mm 



Full overlay Straight 

348.78.700 


Hinge arm 

crank Dim. A Dim. B Dim. C Dim. A and B 

Straight 8.5 19.0 63 + mounting plate 

8 mm 16.5 27.0 63 

reinforcement 

16 mm 26.9 37.4 65 + door thickness 



420


3303/4303 Blind Corner Snap-on Hinges – Grass 

Frame-mounting hinge with snap-on feature 

• Door thickness 16 - 22 mm 



• Tab: 2.5 - 5 mm 

• Blind corner hinge can only be used with 

mounting plates found on page 422 


B 

Door closed 



421 

6 

25.3 

79.5 

C 


15 

Gap 

Cup spacing 

Factory setting 

Mounting 

plate 

4.3 

42 

Depth 12.7 

42 

Depth 12.7 

Depth 12.7 

Frame-mounting hinge 

Door 

8 

11 

11 

Tab 

35 

Tab 

35 

Tab 

35 



Hinge arm: zinc alloy 

Mounting 

Inset 


Hinge arm 




Hinge arm: zinc alloy 

Mounting 

Inset 


Twist Lock 

Mounting 

Inset 


Hinge arm 


Door thickness 

in mm 

16 

17 

18 

19 

20 

21 

22 

Hinge arm 


Hinge arm 


Dim. B 

26.5 


Dim. C 

42.5 

Minimum gap 

in mm 

0.5 

0.5 

0.5 

0.8 

1.2 

1.8 

2.4 

Flat Head 

#6 

nickel-plated 

348.69.602 

nickel-plated 

348.69.657 

nickel-plated 

348.49.600 




black 348.79.304 



The values in the 

adjacent table are 

based on a door 

corner radius of 

one millimeter. 






3000/4000 Mounting Plates for 

Snap-on Frame Mounting Hinges – Grass 



Raised flat head wood screws pages 309-310 

Varianta screws page 311 


14 

min. 

40 

32 


14 

3 or 5 

min. 

40 

Rear of 

frame 

Rear of 

frame 

32 

32 

• Screw-mount 

Material: die-cast 




4.3 mm 


4 

348.82.543 

• Suitable only for 3303/4303 Blind Corner hinges 

found on page 69 


Material: die-cast 

Door closed 

Door 

Special 

mounting 

plate 

Rear of 

frame 

Flat Head 

#6 

VARIANTA 

5 


4.3 mm 


4 

348.82.641 

• Suitable only for 3303/4303 Blind Corner hinges 

found on page 69 



422


3000/4000 Mounting Plates for Snap-on Hinges – Grass 

Mounting plates 



423 


17 32 



1.3 mm 1 

348.80.012 

4.3 mm 4 

348.80.049 

9.3 mm 


9 

348.80.094 

Mounting plates Drilling diagram 

• Press-fit into 10 mm holes 


2 

Door Side 

panel 

17 32 


50 

12 deep 

10 

32 

• Door gap 2 mm 





1.3 mm 1 

348.81.019 

4.3 mm 4 

348.81.046 

9.3 mm 


9 

348.81.091 



Flat Head 

#6 


1.3 mm 1 

348.82.016 

4.3 mm 4 

348.82.043 

9.3 mm 


9 

348.82.098 






Mounting Plates for 3000/4000 Snap-on Hinges – Grass 

• Distance between Door and Side Panel, 2 mm 

Wing mounting plates 

2 

Door Side 

panel 

Drilling 

diagram 



• With pre-mounted euro screws 

• Screw-mount in series-drilled holes 


Face-frame mounting plate 10 9.5 



37 

5 

32 

32 

48 


1.3 mm 1 

348.82.212 

4.3 mm 4 

348.82.249 

9.3 mm 


9 

348.82.294 


2.6 mm 2 

348.26.022 

4.3 mm 4 

348.26.024 

7.3 mm 


7 

348.26.027 



424


3000/4000 Series Accessories – Grass 

Pozi-drive #2 Screwdriver 



425 

Material: steel, plastic 



• Pozi-drive screwdriver must be used when 

adjusting hinges 

Spacer Wedge • Compatible with all Snap-on and Twist Lock 

series hinges 

• Degree: 7.5º 

Mounting Plate Spacer 

X 



• Height: 3 mm 



Twist Lock Cup • Used for hardwoods 



Cat. No. 

006.33.002 

Cat. No. 

348.82.837 

Cat. No. 

348.82.823 

Cat. No. 

348.47.030 





Airmatic Door Stop – Grass 

Door Stop, airmatic 

Wing Adapter Plate, airmatic 

Adapter Plate, airmatic straight 


• Design useful for insets 



• Install by drilling a 10 mm (3/8") x 60 mm (2 3/8") 

hole in the front edge of the cabinet 

• For optical solutions 



grey 356.13.500 


• Suitable for 28 mm (1 1/8") and 37 mm (1 7/16") 

hole patterns 



grey 356.13.510 


Flat Head 

#6 



grey 356.13.530 




426


Easy Mount 

• Door thickness 16 mm (5/8”) 

• Side panel thickness 16 to 22 mm (5/8” - 7/8”) 

• Horizontal and vertical adjustment, oblong holes 




427 

Edge of inset door 

19 

8 

Max. door opening angle: 

32 32 

6 

19 6 8 

16 

16 

Door overlay For inset mounting: 

side panel 

+ door thickness 



Flat Head 

#6 

zinc-plated 

non self-closing 343.33.917 

self-closing 343.33.920 


Examples of corner gaps - for single-side and overlay door mountings: 

Side panel 

Thickness 

No. of shims Gap Door overlay 

20 - - 20 

21 - 1 20 

22 - 2 20 

If the side or centre panels are thinner than those shown in the table, 

insert a shim under the hinge mounting plate. 

Shims can also be used to achieve wider corner spacing or gaps. 

The shims are stackable. 






Pie-cut Corner Hinge 

• With two 35 mm cup holes, screw-mounted 

• Door thickness variable 15-24 mm 

• Hole size: 35 mm diameter, depth 11 mm 

A rugged hinge designed for revolving-shelf kitchen cabinet installations. The 

pie-cut corner hinge meets all design requirements for three-way adjustability, 

quick mounting, concealed installation and sturdy construction. Adjustable to 

allow a small air circulation gap. 

Max. opening angle: 78 

Door 

Side panel 

Door open 

Pie-cut hinge 

Side panel 

Door closed 

Mounting plate 


Wide-angle 

hinge 

Mounting plate 

Wide-angle 

hinge 

Door 

48 ø35 

Door 

13.5 

Side panel 


18.5 

18.5 

13.5 

11.3 depth 

ø35 

48 







15 

9 

2.5 

Specially designed for kitchen corner 

cabinets with revolving shelves. 

Adjustment 10 

15 

10 

78º 

2.5 

9 

24 

2.5 

Flat Head 

#8 

Adjustment 10 

1.2 

1.2 

24 



428 

10 

2.5


S-Series Stainless Steel Hinge 

Pivot pin for hinge arm is steel, sealed against corrosion 

S-Series hinge will only work with S-Series mounting plate 

Door thickness 15 to 20 mm (9/16" - 13/16") 

Side panel thickness from 16 mm (5/8") 

Tab = 3 - 5 mm 



429 


S-Series Mounting Plate, flanged 

43 

43 

depth 11 

depth 11 

Hole 

Pattern 

37 

4 

4 

3 

Tab 

35 

Tab 

35 

32 

Screw-mount, self-closing 

Material: 304 stainless steel 


Mounting Hinge arm Type Cat. No. 

Full overlay straight 16 327.20.000 

Half overlay 9 mm crank 6 327.20.002 

Packing: [200 pcs.] (Includes stainless steel screws) 

Text 

Change 

Screw-mount, free-swinging 

Mounting Hinge arm Type Cat. No. 



Packing: 40 pcs. (includes stainless steel screws) 

Discontinued 

Press-fit, 45/9.5, self-closing 

Material: 304 stainless steel 


2 mm 2 327.30.000 

Packing: [400 pcs.] 

Text 

Change 




Institutional Hinges 

Advantage 5K Grade 1 Hinge 

• ANSI/BHMA A-156.9-2001 Grade 1 approved 

• Universal usage on 3/4” & 13/16” materials 

• 14 gauge steel 

• Hinge knuckles broached for precision pin alignment and 

smooth operation 

• Hinge leaves punched after forming for precision alignment 

• “Easy Hang” feature - requires one person operation for 

hanging large doors 

Advantage 5K Hinge 


Hole 

pattern 

45 

(1 3/4”) 


37 



• Pre-mounted 5 mm Euro Screws 

• Universal drill pattern consistent with Aximat and concealed hinges 

• Standard drilling equipment can be used 

• Standard 37 mm set back and 32 mm system drilling 

Press-fit Drilling diagram 

45/9.5 

32 

32 

32 (1 1/4”) 

• Offset hole pattern allows 

for larger mounting screws 

45 

13 deep 

9.5 

Ø6 

(1/4”) 

5 

27 

17.5 

22.5 

45 

(1 3/4”) 

21 

(13/16”) 

Ø5 

6 

(1/4”) 

37 

(1 7/16”) 

45 

(1 3/4”) 

14 

(9/16”) 

21 

(13/16”) 17.5 

(11/16”) 

10 (3/8”) 6 (1/4”) 

Ø6 

(1/4”) 

Pan Head 

#8 

2.5 (7/64”) 

70 

(2 3/4”) 

45 

(1 3/4”) 

Material: steel, powder-coated or plated 


powder-coated matt black 354.65.300 

powder-coated dull chrome 354.65.200 

powder-coated pearl 354.65.700 

plated brushed nickel 354.65.410 

plated matt nickel 354.65.400 




430


Prämatic with Exposed Axle, 8 mm Gap 

Corner hinge with spring, for flush-fit mounting. 

Side panel 



431 

21 

19 

5 

8 

11 

Door 


Centre panel hinge with spring, for centre panel mounting. 

Side panel 

Centre panel 

Door 

35 

52 

13 deep 

21 

9 

Screwmounted 

Hole pattern 

52/9 

21 

12.5 

19 

19 

5 

8 

5.5 

5 

8 

5.5 

35 

52 

13 deep 

Door 

Door 


Twin hinge with spring, for twin door mounting. 

9 

10 

Press-fit 

Hole pattern 

52/9 

12.5 

35 

45 

13 deep 

9.5 

8 

Press-fit 

Hole pattern 

45/9.5 


12.5 

Prämatic hinges 

with exposed axle 

• For side panel thickness 19 mm 

• For door thicknesses 16 to 21 mm 

• 8 mm gap 

12 

37 

5 

• Door overlay: 11 mm 



nickel-plated 

screw-mounted 52/9 344.00.000 

press-fit hole pattern 52/9 344.00.100 

hole pattern 45/9.5 344.00.200 

Packing: 20 and 100 pcs. (includes Varianta special 

screws for side panel mounting) 

• Door overlay: 5.5 mm 


nickel-plated 



hole pattern 45/9.5 344.00.201 





nickel-plated 



hole pattern 45/9.5 344.00.202 




32 




Prämatic-SM with Exposed Axle, 3 mm Gap 

35 

52 

13 deep 

9 

Screwmounted 

Hole pattern 

52/9 

Side panel 

23 

12.5 

19 

5 

3 

Door 


35 

45 

13 deep 

9.5 

Corner hinge with spring, for flush-fit mounting 

8 

Press-fit 

Hole pattern 

45/9.5 

12.5 

C 

Prämatic-SM hinges 

with exposed axle and rapid assembly 

system on the side of the door 

• For door thicknesses 16 to 21 mm 

• 3 mm gap 

• For inset doors 

R=min.2 

22.5 

B 

A 

1 

optional from 

60 


22.5 

5 

32 




nickel-plated 



Packing: 100 pcs. (includes Varianta special screws 

for side panel mounting) 

Dim. A Dim. B Dim. C* 

60 mm 180° 4 mm 

62 mm 172° 6 mm 

63 mm 164° 7 mm 

64 mm 156° 8 mm 

65 mm 149° 9 mm 

66 mm 143° 10 mm 



432


Prämatic Glass Door Hinge with Exposed Axle, 3 mm Gap 

• With spring 

• 3 mm gap 

• Glass thickness 4 to 8 mm 

• With lateral adjustment up to 3 mm 

• With vertical adjustment ±2 mm 

• Assembly instructions included 


Glass door hinge, with exposed axle for inset doors 



433 

Opening angle: to 

74 

37 0.2 

D50 + A 

C 

22.5 

min. gap = 3 mm 

9 0.2 

16-0.4 

19 

7 

B 

Angle 

D 50 + A 

5 

2.9 

A 

32 

9.6 

53 

26 

28 


56 

32 

Flat Head 

#6 




Packing: 1 pc. (includes Varianta special screws for 

side panel mounting) 

Glass thickn. A 4 5 6 7 8 

Min. chamfer B 0.5x45° 1x45° 2x45° 3x45° 4x45° 

Dim. C 6.9 5.9 4.9 3.9 2.9 

Angle 210° 200° 190° 180° 170° 

Raised head screw L=8 L=10 L=10 L=12 L=12 

M5xL DIN 7985 






Prämatic with Exposed Axle, 6 mm Gap 

52 0.1 

8.3 deep 

41.2 +0.2 

14 +0.1 

R6 

15.5 0.1 

Center panel hinge with spring, for side panel mounting 

Side 

panel 

13 

13 

4.5 

6 

3.5 

Door 


Twin hinge with spring, for twin door mounting 

Door 

Center 

panel 

13 

13 

4.5 

6 

3.5 

Door 


Prämatic special hinges 

For laminated boards and phenolic boards 

• With exposed axle – height 40 mm 

• For side panel thickness 13 mm 

• For door thicknesses from 10 to 13 mm 

• Door offset 7 mm at 90° 

• Theft prevention due to secured axle 

• 6 mm gap 

Chamfer minimum: 

1 mm x 45° 

12 0.1 


3.6 

32 0.1 
















434


Prämatic All-Glass Display Cabinet Hinge 

with Exposed Axle, 3 mm Gap 

• With spring 

• 3 mm gap 

• Glass thickness 4 to 8 mm 


• With vertical adjustment ±1.5 mm 



435 

2000 

1500 

1000 

500 

Opening angle: to 

≤ 7 kg 

≤10 kg 

≤15 kg 

≤ 19 kg 

≤ 24 kg 

2 2 3 3 4 


• Guide for 8 mm glass door thickness 

• Hinge spacing min. 500 mm 

• Door widths up to 600 mm 

• Doors not wider than high 

D 

-0.4 

372 

37 

2 

16-0.4 

+2 

+2 9 9 

2.9 

36.7 

D 

C 

6 

A 

Min. 

gap= 3 

B 

Angle 

2.9 

A 

9.6 

26 

28 


53 

37 




Packing: 50 pcs. (includes mounting material and 

assembly instructions) 

Glass thickn. A 4 5 6 7 8 

Min. chamfer B 0.5x45° 1x45° 2x45° 3x45° 4x45° 

Dim. C 6.9 5.9 4.9 3.9 2.9 

Dim. D-0.4 17.8 18.8 19.8 20.8 21.8 

Angle 210° 200° 190° 180° 170° 

Raised head screw L=8 L=10 L=10 L=12 L=12 

M5xL DIN 7985 





Regula with Exposed Axle, 6 mm Gap 

• For side panel thicknesses 19 mm 

• For door thicknesses up 20 mm 

• Gap 6 mm 


• With vertical adjustment ± 2 mm 

• Door overlay: 13 mm 

• Screw-mount, with spring for side panel 

mounting in hole pattern 48/6 

Regula corner hinges, with exposed axle 


35 

48 


250 0 

6 

12 deep 

14 

10.5 

37 


32 

Side 

panel 

1 

6 

19 

13 


Door 





22 

13 

1 

Flat Head 

#6 



436

Mitre Hinges 

For Doors and Flaps 

Three-way adjustable: 

3 mm in height, 1.5 mm in depth and width 

GS 45/90 mitre hinge, screw-mounted 

• Chamfer: 45° 


• Side panel thickness: 16 to 22 mm 



437 


GS 22.5/135 mitre hinge, screw-mounted 

• Chamfer: 22.5° 




Mitre flap hinge, screw-mounted 

• Chamfer: 45° 

• Flap thickness: 16 to 22 mm 


• Use in combination with flap and lid stays 


Height 

Width 

Hole pattern Sample installation: 

5.5 7 7 5.5 

35 

52 

depth 13.5 Chamfer 45° 

Hole pattern 

5.5 13 13 

5.5 

52 

35 

35 

52 

35 

52 

Hole pattern: 

5.5 7 7 5.5 

35 

52 

Door 

Side 

panel 

depth 13.5 Chamfer 22.5° 

13.5 deep Chamfer 45° 

Depth 

Height 

52 

35 

Door 

Sample installation: 

Sample installation: 



Door 

Side panel 

Door open 

Side panel 

Door closed 






Door open 

Door 

Side panel 






Flap 

Side panel 

Door 

Door closed 

Panel 

Flap 

Flat Head 

#6 

Pattern 

Flap open Flap closed 









Drill In Concealed Hinges 

Zysa 

Nonhanded: can be used left or right 

Tighten the tensioning screw to ensure a secure grip in wood 

Additional holding power for exceptionally high loads is achieved by installing a particle board 

or wood screw through exposed end 

Drilling must be extremely accurate 

Zysa hinges 

Material: brass, matt w/ Stock 

Cat. No. [341.21.510] 341.21.520 341.21.530 341.21.540 

Wood thickness 14 -19 17 - 22 20 - 26 22 - 28 

Screw* dia. 2.5 dia. 3.0 dia. 3.5 dia. 3.5 

Length L 11 13.5 15.5 16.5 

Hole dia. 10 12 14 16 

Hole depth T 11 13.5 15.5 16.5 

Dimension A 16.5 20 23 25 

Dimension B 2 2.2 3 3 

Joint F 


2.5 3.5 3 3 

Butting, inset door: 

Butting, overlay door: 

Door closed Door open 

Door closed Door open 

Joining two panels: Butting overlay doors: 

panel 

hinge 


side panel 

panel 

door 

door 

panel 

hinge panel 

Discontinued 

Panel closed Panel open Flap-door closed 

Flap-door open 

Typical folding door installation: 


side panel 

hinge 

hinge 

hole dia. 



dimension A 

F 

dimension B 

L T 

flapdoor 

hinge 

bottom panel 

side panel 

door 

door 

bottom panel 

hinge 

Flat Head 

#6 

hinge 

hinge 

Hole pattern, Zysa hinges 

side panel 

flapdoor 



438


Soss 

• Soss hinges are shown on page 439 

Door 

width 

mm 

100 

200 

300 

500 

900 

700 

1250 

1750 

Door 

weight 

kg 

225 

180 

135 

90 

70 

45 

35 

Choosing the right soss hinge: 

1) Determine width, thickness and 

weight of the door 

2) Draw a straight line on the chart, 

starting on the left hand side at the 

appropriate point on the Door Width 

column and running through the 

correct point on the Door Weight 

column to end at line A 

3) By looking down the column you will 

see the number of hinges required 

and at the foot of the column the 

relevant hinge number 

Example: 

A door 760 mm wide that weighs 90 kg 

and has a thickness of 41 mm would 

require four Soss hinges No. 218. The 

dotted lines shows how this result was 

determined from the chart. 



438 A 

25 

15 

10 

7 

5 

Hinge 

Number 

A 

Minimum Door Thickness mm 

19 17 19 14 13 14 19 22 28 35 41 48 

4 

3 

2 

103 303 203 314 101 205 204 208 212 216 218 220 

Fully closed position 

C 

Fully open position 

A 

B 

The diagram above shows a section through a 

wood mounted hinge assembly in its fully 

opened position. It gives the unique elliptical 

path travelled by a SOSS hinge from closed at 

0º to its full 180º opening. 


Recommended router cutters and guide 

bushes for each SOSS hinge type are 

listed below (not supplied) 

Hinge Two flute, long Guide 

type shank router cutter* bush* 

101 5.0 mm 12 mm 

203 9.0 mm 16 mm 

204 9.0 mm 16 mm 

208 12.7 mm 20 mm 

212 12.7 mm 20 mm 

216 12.7 mm 20 mm 

218 12.7 mm 20 mm 

220 12.7 mm 20 mm 

Suggested routing depths 

Hinge Shallow Deep 

type mortise* mortise 

101 5.5 mm 13 mm 

203 5.0 mm 20 mm 

204 6.4 mm 20 mm 

208 7.0 mm 25 mm 

212 9.5 mm 29 mm 

216 12.0 mm 39 mm 

218 10.3 mm 43 mm 

220 11.9 mm 51 mm 

* Adjust this dimension to suit your application 

and always try a test hinge assembly with 

your selection of cutters and guide bush 

prior to production 

Soss Hinge A (mm) B (mm) C (mm) 

101 2.4 2.7 0.8 

203 3.2 2.7 0.8 

204 3.2 2.7 1.6 

208 4.0 3.5 1.2 

212 4.8 4.0 1.2 

216 6.4 5.5 1.6 

218 6.4 9.5 1.2 

220 8.4 11.8 1.6 

The table above gives hinge clearances. 

Measurement A can be reduced as required 

but must not be exceeded. The jig is set for 

routing measurement A at its maximum. 




Vici & Soss 

Hole pattern, Vici hinges 

Hole pattern, Soss hinges 



439 



T1 

Soss hinges 

Material: Case: zinc die-cast 

Linkage: steel 

Vici hinges 

Material: Surface: brass, matt 

Joints: steel, brass-plated; Housing: steel, unfinished 


Cat. No. 341.05.500 341.05.530 

Wood thickness 18 - 20 ( 11 /16" - 13 /16") 24 - 26 ( 15 /16" - 1") 

Screw diameter required 4.0 4.5 

Width 12 18 

Length L1 39 79.5 

Length L2 12 28 

Depth T1 1.5 2.5 

Depth T2 15.5 21.5 

Dimension A 24 29 

Dimension B 4 3.5 

Joint F 4 4 


width 

L1 L 2 

T2 

T1 

L1 

Text 

Change 

dimension A 

width 


L2 

T2 

F 

dimension B 

F 

dimension A 

dimension B 

Flat Head 

#6 

Soss # 101 203 204 208 212 216 218 220 

brass-plated 341.07.518 341.07.527 341.07.536 341.07.545 341.07.554 341.07.563 341.07.572 341.07.581 

nickel-plated 341.07.718 341.07.727 341.07.736 341.07.745 341.07.754 341.07.763 341.07.772 341.07.781 

Wood 13 - 16 19 - 24 19 - 25 22 - 26 28 - 34 35 - 38 41 - 45 50 + 

thickness ( 1 /2" - 5 /8") ( 3 /4" - 15 /16") ( 3 /4" - 1") ( 7 /8" - 1") (1 1 /8" -1 5 /16") (1 3 /8" -1 1 /2") (1 5 /8" -1 3 /4") (2"+) 

Width 9.5 13 13 16 19 25.5 28.5 34.9 

Length L1 42 44.5 60 70 95.3 117.5 117.5 139.7 

Length L2 22 20 31 36.5 53 65.5 79 74.61 

Depth T1 5.5 5 6.4 7 9.5 12 10.3 11.91 

Depth T2 6.5 13.3 11.9 15 17.5 24.5 31 37.50 

Dimension A 17 22.1 22.1 27.5 32.6 43.8 50.8 61.92 

Dimension B 2.4 3.2 3.2 4 4.8 6.4 6.4 7.14 

Joint F 2.7 2.7 2.7 3.5 4 5.5 9.5 12.70 

Packing: 24 pcs. 10 pcs. 10 pcs. 10 pcs. 2 pcs. 2 pcs. 2 pcs. 2 pcs. 

(includes mounting screws) 




Glass Door Hinges 

Non-Bore Hinge For Light-weight Glass Doors 

• Ideal for RTA industry 

• Easy to install glass doors clip easily onto cabinet after hinges are 

mounted on glass 

• Pivot pins rotate freely in a 5 mm diameter hole bushings are not 

required 

• Door clearance spacing incorporated into hinge 

• Magnetic catches see pages 211–214 

Simplex Hinge, Speed-mount 

• For glass doors thickness 6.5 mm (1/4") 

20 

2 

11 

11 

2 

40 

40 

Ø 5 mm 

8 

13 

Fixed pin 

13 

20 

Ø 5 mm 

Spring-loaded 

Simplex-Inset glass door hinge, screw-mounted to side of cabinet 

• Self-adhesive pressure plates and screws included 

• Packaged in pairs for left or right-hand installation 

• Glass thickness to 5 mm (3/16") 


For For Inset inset doors doors 

min. 

1.5 

33 19 

Side panel 

Glass door 

Dimensions shown on mounting diagrams are only approximate. 

Please conduct a trial mounting to determine your exact dimensions. 

Glass 

door 

16 


Min. 15 mm Min. 15 mm 



Gap between glass 

and sides = 5 mm 


black 

Packing: 40 pairs (inserts not included) 

361.44.300 

2 

40 

Top Upper panel 

shelf 

Min. 25 mm 25 mm 

Hole pattern (top) 

33 

19 

Side panel 



chrome-plated 361.33.221 

Packing: 100 pairs (50 right and 50 left) 

16 



440 

5 mm 

5 mm


Non-Bore Hinges For Light-Weight Glass Doors 

Simplex-Inset glass door hinge, with press-fit bushing 


• Glass thickness to 5 mm (3/16") 

Simplex-Inset glass door hinge, with press-fit bushing 


• Glass thickness to 6.5 mm (1/4”) 



441 

13.5 

Glass door 

20 

Glass door 

2 

2 

40 

10 

to 12 

40 

8 

Bottom 

panel 

10 

to 12 

8 

2 

Ø 8.8 

2 

Bottom 

panel 

Ø 8.8 

Side panel 

10 

to 12 

Side panel 

10 

to 12 

Decorative-Inset glass door hinge, with press-fit bushing 

• Steel set screw with plastic pad 

• Glass thickness to 6 mm (1/4”) 

Glass Door Hinge-Inset with closed end, and press-fit bushing 

• Steel set screw with plastic pad 

• Glass thickness to 6 mm (1/4”) 

16 

20 

3 

1.5 

Ø7 

min. 

Glass door 

11 

min. 9 

8 

Bottom 

panel 

16 

34 

Side panel 

Side panel 

2 

2.5 

Ø7 

Glass door 

min. 

12 

min. 9 

8 

Bottom 

panel 

For inset doors 

min. 

1.5 

min. 

1.5 


Side panel 

Glass door 


For inset doors 

min. 

1.5 

min. 

1.5 

Side panel 

Glass door 


Side panel 

Glass door 


Side panel 

Glass door 

Dimensions shown on mounting diagrams are only approximate. 

Please conduct trial mounting to determine your exact dimensions. 


Material: steel; Bushings: plastic 



brass-plated 361.42.800 

black 361.42.300 

Packing: 50 pairs (1 pair = 1 left, 1 right) 

Material: steel; Bushings: plastic 




black 361.42.319 

Packing: 50 pairs (1 pair = 1 left, 1 right) 


Fastening screw: steel; Bushing: plastic 


matt black 361.69.310 



Fastening screw: steel; Bushing: plastic 


matt black 361.69.320 

Packing: 50 pairs 

• Decorative Handles please see page 442 

• Magnetic catches see pages 211–214 




Glass Door Hinges and Pulls 

• Maximum door weight 4 kg (8.8 lbs.) 

• Maximum door sizes: width 350 mm (13 3/4”) 

height 800 mm (31 1/2”) 

All-Metal Hinge, with catch 

• Econo version of a non-bore glass door hinge 

• Screw-mounts to side of cabinet 

• Vertical adjustment with oblong holes 


Glass Door Pull, with plastic screw 

• Glass thickness maximum 5 mm 


Side panel 

Glass 

door 

Glass 

door 



2 

30 

min. 

25 

Minimum 2.5 mm gap between glass and panels. 



textured black-plated matt 361.93.340 

textured brass-plated matt 361.93.840 

textured chrome-plated matt 361.93.240 

Packing: 50 pairs (1 pair = 1 left, 1 right hinge) 

Glass Door 

Side panel 

40 

16 



442 

Side 

panel 



textured chrome polished 154.25.210 

textured brass polished 154.25.810 


32 

21 

30 

31 

40 

Glass Door 

No hole in glass required 

4-6 



nickel matt 154.18.701 


26 

Pan Head 

#8 

2


For Light-weight Glass Doors 

Claronda Glass Door Hinge, screw-mounted 

• Stylish solid brass hinges for inset doors 

• Installation requires drilling a hole in glass 

• Door and side panel components installed separately 

• Door component detaches by removing mounting screw 

• Reversible: can be used left or right 

• For glass thicknesses 4.0 (3/16”) to 6.0 (1/4”) mm 

To determine the exact tab distance for your 

application, please make a trial 

mounting with 1/4” wood material. 

Glass Door Hinge, screw-mounted 



443 


• Exposed-knuckle hinges with 3 mm (1/8”) horizontal 

adjustment for inset doors 

• Installation requires drilling a hole in glass 

• Thumbscrew secures glass 

• Reversible: can be used left or right 



• Max door weight 4 kg. (8.8 lbs.) 

• Max door size : Width: 350 mm (13 3/4”) 

Height: 800 mm (31 1/2”) 


Glass Door Hinge, screw-mounted, for inset doors 


• 1 left and 1 right hinge per mounting 

• Max door weight 4 kg. (8.8 lbs.) 

• Max door size : Width: 350 mm (13 3/4”) 

Height: 800 mm (31 1/2”) 


• Remove protective backing from adhesive tape 

• Position pressure plate on glass door 

• Attach hinge body to base 

• Adjust glass door 

• Tighten mounting screws 

Pan Head 

#8 

Flat Head 

#6 

Flat Head 

#6 

Side panel 

Min. .5 mm gap 

Glass 

door 

Protective 

backing 

Strike 

Glass 

door 

Side panel 

Glass door 

Adhesive tape 

Hinge body 

Pressure plate 

Hole pattern 

Hole 

in glass 


Material: solid brass 


chrome-plated, polished 361.47.207 

Packing: 10 pcs. (two hinges per mounting required) 


20 

25 

approx. 

19-20 mm 

Hole pattern 

32 

4 

Plastic washer 

approx. 17 mm 

Plastic 

washer 

12 

18 

Adjustment cam Plastic 

washer 

Glass door 

2 

Side 

panel 

20 

30 

45 

32 

R10 

50 

Side 

panel 

Material: brass 


brass matt 361.85.501 

nickel-plated, matt 361.85.609 


Hole pattern 

Side panel 

Glass door 

Side 

panel 

Bottom panel 



nickel-plated matt 361.49.603 


Packing: 20 pcs. (10 left, 10 right) 

6 

29 40 

Flat head screws pages 302-304 

Pan head screws pages 304-305 



Furniture Hinges 

For Wood Doors and Lids 

• Magnetic catches see pages 199 - 203 

Simplex-wood mini door hinges 

• With press-fit bushing 

• Reversible (can be used left or right) 

• Plastic bushings and screws included 

• Wood thickness 14 mm to 19 mm 

• Packaged in pairs for left or right-hand installation 


Simplex-wood door hinges 

• With press-fit bushing 

• Reversible (can be used left or right) 

• Plastic bushings and screws included 

• Wood thickness 14 mm to 19 mm 


• Dimensions shown on mounting diagrams are only approximate 

• Please conduct trial mounting to determine your exact dimensions 

New 

Item 

3 to 7 

For flush-fitted doors 


2 

to 

4 

Side panel 


Wood Wooden door door 

Material: steel; Bushing: plastic 


black 361.34.398 

Packing: 1,000 pairs 

For flush-fitted doors 

Side 

panel 

Wood Wooden 

door 

Material: steel; Bushing: plastic, black 



black 361.42.391 


16 

Side panel 

20 

2 14 2 

Complete with 

fastening 

materials 

Ø 9.5 

10 

to 12 9.5 

Shelf 

10 

to 12 

Wood Wooden door door 

19 

2 

16 

Complete with 

fastening 

materials 

40 

10 

to 12 

9.5 

Shelf 

Side panel 

2 

Ø 8.5 

17 

10 

to 12 



443 A


Piano Hinge 

• Hinges are post-plated and free of machine oil 

• Stainless steel is 304 grade with a bright anealed (BA) finish 

• BA finish provides a shiny, more decorative look 

• All holes are countersunk for screws 

• Hinges can be cut by the customer to desired length 

• Special order hinges are available in a minimum quantity of 300 ft. (steel) and 150 ft. (stainless steel) 

• Order 1 pkg. (72 pcs.) of screws for each hinge 



Continuous Hinge 

For furniture, cabinetry and marine applications 

Knuckle length: 12.7 mm (1/2”) 

Hole spacing: 50 mm (2”) 

Length: 1828.8 mm (72”) 

Material Colour Open Width (B) Gauge (A) Pin Diameter (C) Cat. No. 

steel polished brass 27 (1 1/16”) 1.02 (.04”) 2.29 (.09”) 351.09.513 

steel polished nickel 27 (1 1/16”) 1.02 (.04”) 2.29 (.09”) 351.09.613 

steel polished brass 31.8 (1 1/4”) 1.02 (.04”) 2.29 (.09”) 351.09.523 

steel polished nickel 31.8 (1 1/4”) 1.02 (.04”) 2.29 (.09”) 351.09.623 

stainless steel stainless steel 31.8 (1 1/4”) .94 (.037”) 2.54 (.1”) 351.10.023 

steel polished brass 38.1 (1 1/2”) 1.02 (.04”) 2.29 (.09”) 351.09.533 

steel polished nickel 38.1 (1 1/2”) 1.02 (.04”) 2.29 (.09”) 351.09.633 

stainless steel stainless steel 38.1 (1 1/2”) .94 (.037”) 2.54 (.1”) 351.10.033 

steel polished brass 50.8 (2”) 1.02 (.04”) 2.29 (.09”) 351.09.543 

steel polished nickel 50.8 (2”) 1.02 (.04”) 2.29 (.09”) 351.09.643 

stainless steel stainless steel 50.8 (2”) .94 (.037”) 2.54 (.1”) 351.10.043 


A 

C 

B 

12.7 

(1/2”) 

50 

(2”) 

1828.8 

(72”) 

Special Screws for Piano Hinges – CSK Philips 


brass #4 x 1/2” 015.19.501 

nickel #4 x 1/2” 015.19.601 

stainless steel #6 x 1/2” 015.19.021 

Packing: 1 pkg. (72 screws) 



444

Butt Hinges 

Hinges with fixed pin, 5 knuckles 

Decorative Butt Hinge 

Shaker style furniture with raised 

panel doors. 

• Highly decorative 

• Solid brass 

• 2-way adjustable 



445 

D 

A 

2.0 

50.0 

8 

B 

C 

41.0 

4.5 

4 

Knuckle diameter (approx.) 5.5 mm 

Material: steel, yellow chromated 

Refrigerator Door Attachment Mechanism 

• For attaching an appliance door to a hinged front panel 

• Allows you to open the cabinet door while the appliance door is being opened 

• One or two fittings may be required, depending on the size of the appliance door 

Open the refrigerator door to 90 o and insert the rail into 

the guide. Screw on the rail perfectly level to the inner 

side of the cabinet door. 

1-2 

90° 


A x B 

(approx.) 

Material thickness 

(approx.) 

Holes 

per wing Cat. No. 

50 x 35 (1 15 / 16" x 1 3 / 8") 1.2 2 354.12.905 

50 x 50 (1 15 / 16" x 1 15 / 16") 


1.0 3 354.12.906 



antique brass 354.22.130 

polished and lacquered 354.22.830 

Packing: 20 pcs. (screws not included) 



brown 568.16.007 


max. 8 


46 

30 

Cabinet 

9 

36 

Fridge 

door 

150 

Cabinet 

door 

Flat Head 

#5 

19.5 

27.5 

Attach the guide to the outer side of the refrigerator door. 


5 




5 

30 

36 

5.5 

36 

5.5 

40 

50 

50 

1 

1.2 

1.2 

Thickness: 1 mm 

Width: 16 mm 

Length: 40 mm 

Screw holes: 5 




Finish Cat. No. 

brass-plated [351.95.503] 

bronze-plated 351.95.101 

zinc-plated 351.95.905 


Thickness: 1.2 mm 

Width: 18 mm 

Length: 50 mm 





bronze-plated 351.95.110 

zinc-plated 351.95.914 


Thickness: 1.2 mm 

Width: 18 mm 

Length: 50 mm 



Discontinued 






446


Screen hinges 

3-part, pivotable in both directions 

Neuform cranked hinges 

Butt hinge for overlay doors 

Cranked hinges 

Butting for front-hung doors 



447 

50 

25 

35 

17 

6 20 6 

40 

20 


Door thickness: 19 – 20mm ( 3 /4" - 13 /16") 

Side panel thickness: from 17 mm 

Barrel length: 40 mm 

#4 



nickel-plated, polished 307.04.708 


2 

3 

17 

17 

20.5 

8 

14 

16.5 

4.5 

4 

Door thickness: 20 – 21 mm ( 13 /16”) 

Side panel thickness: optional 

Barrel length: 50 mm 


#4 

Colour left right 

polished 307.01.832 307.01.823 

nickel-plated, matt 


307.01.636 307.01.627 


18.5 

36 

6 

Material: brass, polished 

Wood thickness Cat.No. 

20 mm ( 13 /16”) 341.20.815 


10 

10 

3 

40 

20 

Flat head wood screws page 310 

60 

3 

21 

21 

17 

4 

36 

#4 

10 

10 

3 




Self-supporting hinges, flush-mounted 

For folding and sewing-machine tables. 

Folding table hinges, flush-mounted 

For panel thicknesses 19 to 22 mm internal hinge. 

Distance between panels is approximately 5 mm. 


Flat Head 

#4 

Flat Head 

#4 





nickel-plated, polished 341.32.708 

matt 341.32.502 

polished 341.32.806 

bronzed 341.32.100 



Material Mortise Hinge brass 

thickness depth dimensions coloured 

ET L x B 

19 16 85 x 47 341.30.508 

22 19 85 x 51 341.30.526 


21 

B 

0.5 

6 2 

L 

65 

7 

ET 



448 

8 

30 

25 

21 

1.5


Prämatic Hinge for Folding Doors 

• From door thickness of 13 mm ( 1 /2”) 

• Same drilling diagram for both wings 

• Pre-mounted with 3 mm gap and central pivot 

• Gap range adjustable from 0-10 mm (0 - 3 /8”) 

• Adjustable pivot displacement 

• Constant spring power for all adjustments 

• Axle bearing in high-resistance plastic bushings 

• Application with all folding doors 



449 

Adjustable symmetric gap FS 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

Fs 

Fs 

aa 

Gap FS = 2 x wing adjustment a 

mm ( max ) 

0 1 1.5 2 3 4 5 

Wing adjustment a 

15 15 

48 48 

35 35 

9 deep 9 deep 

a 

mm ( max ) 

Flat Head 

#6 


Material: zinc 


chromatized 343.91.900 


5 

4 

3 

2 

1 

Fu 

mm ( max ) 


Gap scheme for symmetric adjustment of wing elements Gap scheme for symmetric adjustment of wing elements 

Fu 

V 

V = door displacement = pivot displacement = gap FU 

For asymmetric adjustment of both wing elements: 

Gap FU = pivot displacement V + adjustment of second wing element 

0 1 2 3 4 5 

V 

mm ( max ) 


Adjustable symmetric gap 

Pivot displacement 


V 



Pivot Hinges 

Corner pivot hinge, straight 


• Max. door opening angle 250° 

• Without stop 

• With outer knuckle 

Corner pivot hinge, cranked 


• Max. door opening angle 180° 

• Without stop 

• With outer knuckle 

Open angle: 

Flat Head 

#6 

Open angle: 

Flat Head 

#6 


side 

panel 

door 

side 

panel 

door 

panel 

panel 



2 

side 

panel 

2 


Length polished 

50 mm (1 15/16") 362.10.803 


side 

panel 

4 

4 

18 

4 

9 


Length matt 

70 mm (2 3/4") 362.01.500 


6 

10 

door 

door 

12 

5 

50 

70 

70 

10 

10 

50 

10 

10 



450 

panel 

panel

Pivot Hinges 

Desk pivot hinge, mounts on drop leaves, screw-mounted 

• With stop 

Max. Opening Angle: 

Pivot hinge, press-fit, for inset doors 

• Door thickness 12 – 21 mm ( 1 /2” - 13 /16”) 

• Both pins spring-loaded: no tools required for installation 

• Detachable 

Max. Opening Angle: 

drop leaf closed 




451 

side 

panel 

drop leaf open 

side 

panel 

drop leaf open 

drop 

leaf 

min. 

7.2 

cabinet 

side 

panel 

open 

12 

15.2 

8.5 

3 

30 


drop leaf 

3 

7 

47 

83 

20 

9 

4 13 

door 

9 

side 

panel 

drop 

leaf 


Flat Head 

#6 


Length Cat. No. 

150 mm 361.50.820 


cabinet 

min. 

10 

Material: plastic; Pivot: steel 


black 361.22.310 

Packing: 200 pairs (2 pins/2 bushings) 

Note: 

To detach door, insert a small screwdriver 

into hole located in door edge. 

Then, use screwdriver to lift springloaded 

pin inside lower bushing. 

Important: Be sure to match holes 

in door and bushing. 

To increase or reduce gap, turn 

tab on its pivot bearing. Once 

adjusted as desired, secure tab 

in position using a small wood 

screw as shown. 


5 

12 8.5 

15.2 

30 18 

4 

77 

7 

27 

13 

14 

150 

13 

6 

door 

side 

panel 

Flat Head 

#4 


12 



Flap Hinges 

Plano Medial flap hinge, screw-mounted 

Sample installations 

16 

Brass arm 


Flap thickness 

15 -16 mm 

Panel thickness 12 mm 

Flap Hinges 


15 -16 mm 


Hole pattern: 

Flap 

16 16 

Panel thickness 16 mm Panel thickness 19 mm 

12 

30 

3 


18 -19 mm 

All-Metal Flap Hinge, three-way adjustable and detachable. The two cups 

can be released and detached for added shipping and installation convenience. 

18 


18-19 mm 



18 

There is a 1 mm gap between flap and shelf when the flap is lowered. 

All-Metal Flap Hinge, with plastic, recessed cup and zinc die-cast screw-mounted flange. 

Adjustable in 3 directions. 

Shelf 


19-21 mm 



Flap 

Gap A 

Flat Head 

#5 

Flat Head 

#5 

Flat Head 

#5 

18 

12 

Overlay adjustable 

from 6 to 8 mm 

12 

35 

Minimum gap 2 mm 

Gap B 

Flap closed Flap open 

9 

35 

Flap 


23.5 

30 

10 

27.5 

30 

8.5 

Panel 


No projecting parts on the cabinet or the flap. 




bronzed 342.75.128 


35 

12.5 





bronzed 342.66.101 


20 

11 

Material: Cups: plastic 

Arm and flange: zinc, die-cast 


black, nickel-plated [342.76.303] 



Discontinued 



452

Flap Stays 

• slotted arm provides sliding action 

• reversible; can be installed left or right 

A 

min. 20 

bottom 

panel 

• with stop 

125 

min. 20 

bottom 

panel 



453 

30 - 45º 

length 

C 

C 

150 

30 - 45º 

flap 

flap 

Flat Head 

#6 

Flat Head 

#6 


5 

24 

26 

16 


5 

24 

26 

16 

10 x2.0 

material thickness 

10 x 2.0 


17 

28 

Flap mounting 


Length Inside Dimension Dimension nickel-plated 

cabinet height A C 

150 min. 125 135 determine 365.10.753 

200 

250 

min. 170 

min. 200 

160 

190 

by trial 

mounting 

365.10.754 

365.10.755 


material 

thickness 

Flap mounting 


18 

16 

17 

26 


Inside Dimension Left 

nickel-plated 

Right 

cabinet height C 

min. 135 


determine by trial mounting 365.60.781 365.60.780 


9 

9 



Flap Stays 

Dorana-stop Flap Stays with Brake, Screw-mounted 

• Braking action is adjustable using adjustment screw, loosen to increase and tighten to reduce 

• Left and right-handed models available 

Keep brake piston rod free of oil, grease and other contaminants at all times. 

34 

20 

15 

16 

32 

46 

32 14 

45 

Material: steel/plastic; Finish/Color: nickel-plated/white 

Length left right 

160 mm (6 5 /16") 365.86.713 365.86.704 

190 mm (7 1 /2") 365.86.731 365.86.722 

220 mm (8 11 /16") 365.86.759 365.86.740 

250 mm (9 13 /16") 365.86.777 365.86.768 

280 mm (11") 365.86.795 365.86.786 



Flat Head 

#6 


Flap 

Flap 

1 

14.5 

11 

Side 

panel 

Side 

panel 

A 

A 

Panel 

Panel 

20 

48 


Length 

Flap open 

Flap 

*C * 

*Dimension C can be determined 

by trial mounting. 

Vertical mounting 

Inside Dimension 

Length Cabinet Height A 

mm (inches) mm (inches) mm 

160 mm (6 5 /16") 250 - 350 (9 13 /16"-13 3 /4") 127 

190 mm (7 1 /2") 300 - 400 (11 15 /16"-15 3 /4") 151 

220 mm (8 11 /16") 350 - 450 (13 3 /4"-17 11 /16") 175 

250 mm (9 13 /16") 400 - 500 (15 3 /4"-19 11 /16") 222 

280 mm (11") 450 - 550 (17 11 /16"-21 5 /8") 222 

Length 

*C * 

Flap open 

Flap 

Horizontal mounting 

Inside Dimension 

Length Cabinet Height A 

mm (inches) mm (inches) mm 

160 mm (6 5 /16") 200 - 300 (7 7 /8"-11 13 /16") 82 

190 mm (7 1 /2") 230 - 330 (9 1 /16"-13") 105 

220 mm (8 11 /16") 260 - 360 (10 1 /4"-14 3 /16") 127 

250 mm (9 13 /16") 290 - 430 (11 7 /16"-16 15 /16") 148 

280 mm (11") 320 - 460 (12 5 /8"-18 1 *Dimension C can be determined 

by trial mounting. 

/8") 171 



454

Flap Stays 

Dorana-stop Flap Stays with Braked and Magnetic Catch, Screw-mounted 

• Braking action is adjustable using adjustment screw, loosen to increase and tighten to reduce 

Keep brake rod free of oil, grease and other contaminants at all times. 

• system hole installation 

• left and right-handed models available 



455 


20 

15 

33-40 

Adjustable 

3 

11 

45 32 

32 

24 

14 

Flap mounting 

Material: steel/plastic 

nickel-plated/white 

Length left right 

160 mm 365.92.711 365.92.702 

190 mm 365.92.739 365.92.720 

220 mm 365.92.757 365.92.748 

Packing: 50 pcs. (1 pc. = 1 left, 1 right) 

VARIANTA 

5 

10 

12 

Flap 

10 

Side panel 


Length 

Flap open 


A 

32 

32 

Side panel 

Panel 

Flap Panel 

32 

32 

A 

37 

5 

C 

37 

5 

Length 

C 

Flap 

Vertical mounting 

Inside Cabinet Dimension Dimension 

Length Height A C 

(mm) (mm) (mm) (mm) 

160 250 to 350 to 114 

190 300 to 400 to 145 

220 350 to 450 to 170 

Flap open 

Horizontal mounting 

Inside Cabinet Dimension Dimension 

Length Height A C 


160 200 to 300 from 58 

190 230 to 330 from 83 

220 260 to 400 from 104 

Determine 

by trial 

mounting 

Flap 

Determine 

by trial 

mounting 




Flap Stays 

“Slow” flap stay, screw-mounted 

Reversible, can be installed left or right, configured for right hand installation. 


Braking action adjustable using 

adjustment screws which attach 

plastic block to side panel. 

Loosen or tighten as needed. 

21 

11 

24 

32 

9x2.0 

9x1.5 

14 

40 

O42 

Flap mounting 

16 

16 

26 

9x1.5 

Flap stay with catch, screw-mounted 

Reversible, can be installed left or right, configured for right hand installation. 

To adjust braking action, loosen 

or tighten screw on stay, as 

needed. 

Flat Head 

#6 

Flat Head 

#6 



Flap mounting 

10 

45 32 

9x2.0 

9 

Flap 

Panel 

Side 

panel 


6 

7 

Side 

panel 

A 

Panel 

A 

min. 24 

min. 37 

Panel C 


Length 

Inside cabinet Dimension Dimension 

Length Depth A C 


150 min. 130 70 

200 min. 170 105 

250 min. 210 140 

Material: steel/plastic, nickel-plated 

Length white brown 

150 mm 365.80.828 365.80.720 

200 mm 365.80.846 365.80.748 

250 mm 365.80.855 365.80.757 


Discontinued 

10 

Length 

Determine 

by trial 

mounting 

Flap open 

Flap 

Material: steel/plastic, nickel-plated 

Length white brown 

225 mm 365.75.710 365.75.112 

275 mm 365.75.729 365.75.121 


C 

Flap open 

Flap 

Inside cabinet Dimension Dimension 

Length Depth A C 


225 min. 190 135 

275 min. 240 175 

Determine 

by trial 

mounting 



456

Flap Stays 

Fall-ex ® with Brake 

Keep brake piston rod free of oil, 

grease and other contaminants 

at all times. 

A 

32 

32 

32 

32 

3 

or 

5 

Bottom panel 

3 

or 5 

32 

32 

32 

A 



457 

37 

37 

C 

Side 

panel 

Length 

Flap open 

Side 

panel 

Length 

Flap 

Reversible: 

Can be installed left or right 

C 

Bottom panel Bottom panel 

Flap open 

Flap 

Side panel 

Bottom panel 

Side panel 

13 

Flap 

Flap closed 

Flap 

Flap closed 

32 45 

Side panel 

mounting 

Piston 

rod 


Twist piston rod to adjust braking action: 

• clockwise to reduce 

• counter-clockwise to increase 


Square tube: brass 

Length (mm) nickel-plated 

250 (9 15 /16") 372.17.753 

325 (12 13 /16") 372.17.762 

450 (17 11 3 5 

/16") 


372.17.771 

Vertical mounting: 

Length Inside Cabinet 

Height 

A C 

250 (9 15 /16") 300 to 400 (11 13 /16" - 15 3 /4") 214.5 Trial 

325 (12 13 /16") 350 to 450 (13 3 /4" - 17 11 /16") 288.0 Trial 

450 (17 11 /16") 400 to 500 (15 3 /4" - 19 11 /16") 406.5 Trial 

Horizontal mounting: 

Length Inside Cabinet 

Height 

A C 

250 (9 15 /16") 300 to 400 (11 13 /16" - 15 3 /4") 22.5 Trial 

325 (12 13 /16") 350 to 450 (13 3 /4" - 17 11 /16") 54.5 Trial 

450 (17 11 /16") 400 to 500 (15 3 /4" - 19 11 /16") 118.5 Trial 


15 

32 

47 

10 

VARIANTA VARIANTA 




Flap Stays 

Stopmatic with Brake 

• Use in left or right-hand installations: just reverse position of foot and 

magnetic catch as needed 

Stopmatic S flap stay with brake, screw-mounted Application drawing 

Stopmatic, flap stay with brake and magnetic catch 

36 

25 


15 

15 

35 

15 

15 23 

45 32 

Adjustable 

33-40 

15 

16 

26 

45 32 

3 

Brake adjustment screw 

Turn clockwise to reduce braking 

action; counter-clockwise to increase. 

11 

14 

14 

Flat Head 

#6 


Length nickel-plated 

200 mm 365.74.713 

250 mm 365.74.722 



Turn clockwise to reduce braking 

action; counter-clockwise to increase. 



200 mm 365.73.716 

250 mm 365.73.725 

300 mm 365.73.734 



8.5 

Flap 

10 

Flap 

Side 

panel 


Keep brake piston rod free of oil, grease and 

other contaminants at all times. 

A 

B 

A 

B 

Panel 

Panel 

28 

37 

Side panel 

Length 

45º 

C 

Flap 

Side panel 

45 

Length 

C 

Flap 

Length 

Inside Cabinet 

Height A B C 

200 

250 

350 to 450 

450 to 550 

238 

288 

115 

140 

Determine 

by trial 

mounting 

300 550 to 650 338 165 

Installs in pre-drilled holes 

Flap 

Length 


Height A B C 

200 

250 

350 to 450 

450 to 550 

238 

288 

115 

140 

Determine 

by trial 

mounting 

300 550 to 650 338 165 



458

Flap Stays 



459 

8 

A 

B 

8 

A 

B 

28 

side panel 



at all times. 

length 

45° 

flap bottom flap 

panel 

C 

“Stopmatic” flap stay with brake, 

with screw-mounted angle bracket 

• reversible, can be installed left or right 

• with quick-mount angle bracket. 


Housing: plastic 


Brake adjustment thumbscrew 

reduce 

braking 

action 

increase 

braking 

action 



Flap mounting 

Length Height Dimension A B C nickel-plated/white 

250 450–550 275 150 determine by 365.40.620 

300 


550–650 325 175 trial mounting 365.40.640 

28 10 

side panel 

45° 

length 

flap bottom flap 

panel 

C 

flap 

“Stopmatic S” flap stay with brake, 

with screw-mounted angle bracket 

• reversible, can be installed left or right 

• with quick-mount angle bracket 


Mounting blocks: plastic 

Without magnet, housing: metal screw-mounted 


A 

B 

bottom 

panel 

37 

length 

45° 

flap 

C 

flap 

Flat Head 

#5 

Flat Head 

#6 


30 

16 

11.5 


24 

15 

Brake adjustment 

thumbscrew 

reduce 

braking 

action 

increase 

braking 

action 

Flap stay with quick-mount 

15 

32 

45 

Flap mounting 

Flap stay with quick-mount 

Length Height Dimension A B C nickel-plated 

200 350–450 238 115 determine 

365.44.600 

250 450–550 288 140 by trial 

365.44.620 

300 


550–650 338 165 mounting 

365.44.640 

16 

26 

Flat Head 

#5 

15 

20 

Flat Head 

#6 

15 

adjustable 

from 

33 to 40 

32 

45 

Flat Head 

#6 

2.3 10 

with magnet 



Ø5 

14 

14 



Flap Stays 

FLAP-EX 

This hinge is particularly suitable for installing in cabinets 

with front flaps. 

The door is opened under spring tension by 

approximately 27° by simply applying pressure directly to 

the door. When the door is closed, the flap is pushed back 

into the cabinet where it is secured by means of the 

Mini Latch catch. 

This flap hinge is designed for installation in cabinet sizes 

from 820 mm (32 5 /16”) high, 400 mm (15 3 /4”) wide and an 

inside cabinet depth of at least 270 mm (10 5 /8”). 

Important: 

The hinge with the coil springs is designed to support a 

particle board front with the maximum dimensions 590 

mm (23 1 /4”) high, 400 mm (15 3 /4”) wide and 19 mm ( 3 /4”) 

thick and a maximum weight when full of 5 kg (11lbs). 

Flat Head 

#6 

Flap hinge "FLAP-EX" 

consists of: 

• 1 screw-mount angle bracket, steel 

• 1 round rod with plastic sleeve, 2 washers 

• 2 coil springs: front = 126 mm (4 15 /16”) long 

rear = 90 mm (3 9 /16”) long 

1 screw-mount bearing, packed loose: plastic 


nickel-plated, white 365.52.708 

Packing: 10 pcs. (completely assembled) 

Mounting instructions: 

Screw the angle bracket to front panel and 

screw-mount bearing to cabinet side panel; see 

mounting drawing on the right. Push round rod into 

the screw-on bearing between the two coil springs. 

Automatic spring catch Mini Latch, screw-mount, with strike 

Pan Head 

#6 




3 

11 

For installation of the front 

flap, 2 cup hinges and a 

Mini Latch catch are 

required, see below. 

23.3 

Catch 

32 

20.5 

13 

34 5 

22 

Front flap 


140 

15 

11 

VARIANTA 

10 

5 

Angle bracket 

35.5 

Strike 

Floor 

11 

3 


The door is opened by pushing against 

the door panel. The pressure triggers the 

release spring in the fitting. The door 

opens automatically.To close the door, 

slightly press against the door panel. 

101 

Coil spring 

126 mm long 

Coil spring 

90 mm long 

Screw-mount bearing 

Washer 

Washer 

12 

254 

28 

32 

Mounting 

diagram 

Door 

Side panel 

Catch 

Strike 

Material: Catch: steel 

Strike: plastic 


nickel-plated, white 245.54.701 




460

Lid Stay 

• Unhanded design 

• Use on doors or lids for chests 



461 

Torque Calculation Chart 

Single spring type A 

Lid open 

A 

C 

Rear panel 

A 

16 

Torque (lbs./inch) Distance Distance Opening 

A C Angle 

35.5 13 97 85º 

44.00 17 93 85º 

53.00 21 89 85º 

62.00 25 85 85º 

71.00 27 85 80º 

Opening angle 

C 

Rear panel 

24 

142 

Lid closed 

Ø 18.5 

Maximum 

54 


24 

34 

16 

26 


nickel-plated/brown 

Type A 372.19.100 

Type B 372.19.110 


To determine optimum mounting please use the torque calculation chart below. Lid weight (in lbs) x (.5 x depth) = torque (lbs./inch) 

Example: A lid that weighs 8.58 lbs. and has a depth of 15". 8.58 (0.5 x 15) = 64.53 lbs./inch. Mount according to the torque calculation chart. 

Distance A = 25, Distance C = 85, Opening angle = 85° 

Double spring type B 

Torque (lbs./inch) Distance Distance Opening 

A C Angle 

62.00 17 93 85º 

79.50 21 89 85º 

106.00 25 85 85º 


18 

Pan Head 

#6 




Lid Stays 

For Wooden Doors 

• Without braking effect 

• Open flap: lift flap until stay engages 

• Close flap: lift flap slightly, stop is released 

Arretop Lid Stay, with automatic lock 

• Open to approximately 75o until lid stay 

engages 

• Lift lid slightly to release 

• Installs left or right 

Folding Lid Stay 

• Locks in open position 

• Thumbscrew adjustment controls door movement 

Door Stay 

Flat Head 

#8 

13.5 

62 

44 

25 

Side panel attachment 

Lid attachment 

15 

45 

32 


14 


Lid in open position 

A 

min. 35 

(min. 55*) 


Dimension A nickel-plated 

Length Lid height Inset lid overlay lid Dimension C left right 

200 max. 500 90 70 Determine by 373.73.710 373.73.701 

250 over 500 120 120 trial mounting 373.73.738 373.73.729 


15 

39 

25 



15 


Size Cabinet Depth Dimension A Dimension C nickel-plated 

200 

250 

210 

260 

150 

180 

Determine by 

trial mounting 

373.70.611 

373.70.620 

300 310 230 373.70.639 


19 

( 3 /4") 

42 

(1 5 /8") 

ø4.2 

Flat head wood screws page 310 


195 

x 

191 

#4 

(7 

53 

1 /2") 

(2 1 /16") 

ø4.2 

16 

( 5 /8") 

Flat Head 

#6 

24 35 

Flat Head 

#5 

11 

11 

17 

( 11 /16") 

9 

28 

(1 1 /8") 

Top 

C 


11 

A 

37 

17 

( 11 /16") 

length 

Material: brass, polished & lacquered 

Length X Cat. No. 

195 mm (7 11/16") 366.33.815 

300 mm (11 13/16") 366.33.824 


Material: brass, polished & lacquered 

Length Cat. No. 

191 mm (7 1/2") 805.06.814 


9 

28 

(1 1 /8") 

C 



462

Lid Stays 

• Raise lid slightly to release lid stay 

• Can be used to limit the door opening angle 

• Trial mounting recommended 

Lid stay 

with joint 

Lid stay 

with slotted guide 

Lid stay 

used as door restraint 

Decorative Door Chain 

used as door restraint 



463 

Flat Head 

#5 

Flat Head 

#5 

Flat Head 

#5 

Flat Head 

#5 

20 

36 27 

25 

17 

23 

36 

8 

44 

12 

Flat Head 

#5 

56 

14 

8 

13 12 

12 

27 40 

20 

13 

22 36 

15 

35 

21 

8 

18 

Flat Head 

#5 

17 25 



nickel-plated 

left 366.35.711 

right 366.35.702 



Cat. No. 

Colour left right 

nickel-plated 366.40.776 366.40.767 

brass-plated 


366.40.570 366.40.561 


nickel-plated 

left 371.32.755 

right 371.32.700 


Flat Head 

#5 

200 mm length (7 7 /8”) 




Cat. No. 

372.35.813 


Top 

Side 

12 

207 

75° 

Length 300 mm 


Top 

Side 

150 Size mm 

Side 

Lid 

Lid 

Door Cabinet Top 

Door 

Size 

150 mm 

Side 

Cabinet Top 




Lid Stays 

Firmatop Lid Stay 

without braking effect 

Lid Stay 

without braking effect 


14 


9 

18 

28 

29 

16 

20 

16 




Top 

A 

20 

75° 


C 

Length 

Lid 

Dual-purpose intergrated spring 

holds lid securely in open or 

closed position. Use one or two 

stays, depending on lid weight. 

Reversible, can be installed left or right handed 

Material: steel or brass 

Length Colour Dimension A Dimension C Cat. No. Packing 

130 

250 

250 

steel, galvanized 

brass chrome-plated 

brass polished 

150 

260 

260 

Determine by 

by trial 


installation 

373.58.705 

373.58.919 

373.58.811 

10 pcs. 

20 pcs. 

100 pcs. 

13.5 


16 

15 



45 

32 

14 


min. 25 

(min. 45*) 

Dimension A nickel-plated 

Length Lid height Inset lid Overlay lid Dimension C left right Packing 

150 max. 250 80 80 Determine by 366.37.715 366.37.706 100 pcs. 

250 max. 1000 160 160 trial mounting 366.37.751 366.37.742 10 pcs. 

A 

Top 

Flat Head 

#5 

Lid 

For light lids use one stay, for 

heavier lids use two stays. 

• To release lift lid slightly 

C 

* Inset lid 

Flat Head 

#5 

Hinges must be used, please see pages 355 - 429 



464

Lid Stays 

Lid stay 

• With spring loaded joint and dependable safety stop 

• Also usable as flap stay 

Note: when used as a flap stay, it is necessary to reverse handing; the right-hand stays installed left, and vice versa. 



465 

Lid 

Rear panel 

150 mm 

Side panel 

23 

32 

9 

10 

Front panel or trim 

Cara-Top Lid stay 

• For light-duty use with adjustable spring 

• Reversible, can be installed left or right 

• Metal mounting plate rotates 180º to switch from left to right 

Flat Head 

#6 

Flat Head 

#8 

11 

32 23 

Flap open position 

34 24 

Flat Head 

#6 

Spring adjustment screw 

40 

16 

8 

9 

Flat Head 

#6 

Lid in 

open position 



nickel-plated 

left-handed 366.30.770 

right-handed 366.30.761 


3 thick 

6 

Stay installation reversible by switching 

spacer sleeve to opposite side. 


Top 

80 

18 

min. 

30 

34 

Length 

Lid 

Material: plastic, steel 


black/zinc-plated 373.53.334 






Flap Stays 

Fall-ex ® 



at all times. 

C 

Length 

Rear panel 

Lid 

100 

Side panel 

Ø3 

or 

5 

32 

32 

32 

A 

Reversible: 

Can be installed left or right 10 

Rear panel 

Lid open Lid closed 



Lid 

13 

32 45 

VARIANTA VARIANTA 

3 5 

Side panel 

mounting 

Flat Head 

#8 

32 

47 



15 

Piston rod 

Twist piston rod to adjust braking action: 

• clockwise to reduce 

• counter-clockwise to increase 


Square tube: brass 


250 (9 13 / 16") 372.17.253 

325 (12 13 / 16") 372.17.262 

450 (17 11 / 16") 372.17.271 


Length Lid height Dimension A Dimension C 

250 (9 13 / 16") up to 300 145 Trial 

325 (12 13 / 16") up to 450 185 Trial 

450 (17 11 / 16") over 450 255 Trial 



466

Lid Stays 

Master-stop lid stay with brake, screw-mounted 

Reversible, can be installed left or right. 

• Braking action infinitely adjustable using adjustment collar 

• Turn clockwise to reduce braking action, counterclockwise to increase 

• As door is opened, end cap snaps over adjustment collar to lock 

door in open position 

Keep brake piston rod free of oil, grease and other contaminants at all times 

B 



467 

Rear panel 

C 

A 

Rear panel 

Lid 

17 

27 12 

9 

Flat Head 

#8 

46 32 


Material: plastic/steel 

Length black/nickel-plated 

260 mm (10 1 /4") 373.74.324 

330 mm (13") 373.74.333 


Dimension Dimension Dimension 

Length A B C 

260 (10 1 /4") 

330 (13") 


15 

Flat Head 

#6 

Adjustment collar 

Lid 

12.5 

Side 

panel 

Determine by trial mounting depending 

on lid opening angle. 





Lid Stays 

Berolina lid stay for vertical lids 

• Apply slight pressure to close lid 


• Snaps into a locked position when fully extended 

• Speed-adjustable 

• Does not support lid during upward movement 

• Left and Right-handed models available 

• Air pressure adjustment at end of cylinder 

Berolina lid stay for horizontal lids 





Length Cabinet depth Dimension A Dimension C Dimension D left 

nickel-plated 

right 

220 min. 270 145 145 determine by 


372.03.795 372.03.740 



Side 

C 

Size 

Lid 

Size 

Top 

D 

D 

A 

• Apply light pressure to close lid 

A 

Pan Head 

#6 

C 

Lid in open 

position 

Pan Head 

#6 

17 

Lid 

Side 


nickel-plated 

Length Cabinet depth Dimension A Dimension C Dimension D left right 

180 min. 230 195 100 determine by 372.04.783 372.04.738 

220 min. 270 235 125 trial mounting 372.04.792 372.04.747 


30 20 

14 


14 

20 

30 



10 

8 

10 

8 

32 42 


32 42 



468

Lid Stays 


20 



R 

469 

20 

R 

L 

L 


• With adjustable braking effect 

R 

20 

Right Left 


32 

32 


R 

L 

L 

20 

232 

143 

84.4 

45 

Lid mounting 

92 

46 

32 

Length 

194.5 Length 

32 

32 30 

50 


93 

Lid 

15 

Flap 

10.5 

12.8 

19.5 


Opening angle screw adjustment 

Lid Stay, lid bracket attachment 

Reversible, can be installed left or right 

200 mm (7 7/8") length 

Material: plastic/steel 

Colour nickel-plated 

black 365.31.300 

white 365.31.700 


21 

Lid mounting 

43 

32 

Lid Stay 

170 mm (6 11/16") length 


nickel-plated 

left 365.31.601 

right 365.31.600 



17 

11 



Bench Seat Hinges, Folding Table Fittings 

• Hinge design ensures safe retention of seat top in raised position at an angle of 95° 

• Guarantees generous degree of forward movement (approximately 110 mm) (4 5 /16”) 

• Unrestricted opening even of fully upholstered seats, as no joint is required between 

the seat and back 

• Hinge joints incorporate a stop to prevent the open seat slamming against the fitting 

• Springs for seat tops weighing 8 and 12 kg (17.6 - 26.4 lbs) counterbalance the 

weight of the seat top and assist opening 

• Screw holes in the bench side panel and seat top are at 32 mm (1 1 /4”) intervals 

Left-hand hinge, without spring - raised (pictured below) 

Left-hand hinge, with spring - closed (pictured below) 


31 

50 

32 

Ø7 

32 

Bench seat hinge, with spring 


1 

64 

100 

191 


Bench seat hinge, without spring 

For light-weight seat tops 



yellow chromated 643.01.506 


VARIANTA 

10 

Seat top 

VARIANTA 

10 

136 


Seat top weight yellow chromated 

approx. 8 kg (17.6 lbs) 643.01.515 

approx.12 kg (26.4 lbs) 643.01.524 


40 

10 

7 

7 



470 

64 

85

Lid/Flap Stay 

Duo 

• Two applications; lid or flap stay 

• Can be mounted left or right 

• Adjustable braking effect 

• Lid/Flap Stay clip mounts to brackets without tools 

• Use of a magnet is recommended when 

used as a flap stay application, see page 199 

• Aluminum doors are on page 486 



471 

Function: 

Set the function to stopping 

or 

braking by adjusting the 

screw with a 4 mm Hex Key. 

(sold seperately - see next 

page) 

45 

(1 3/4") 32 

(1 1/4") 

15 

(9/16") 

6.5 

(1/4") 

25 

(1") 

Cabinet mounting bracket 

4 

(3/16") 

32 

(1 1/4") 

45 

(1 3/4") 

27 

(1 1/16") 

17 

(11/16") 

17 

(11/16") 

13 

(1/2") 

Wood or aluminum frame 

mounting bracket 

4.5 

(3/16") 

14 

(9/16") 

8.5 

(5/16") 

Aluminum frame mounting 

bracket 


Wood Door Lid Stay Aluminum Door Lid Stay Flap Stay Doors 

Duo Lid/Flap Stay Arm 


Version nickel-plated 

A 6 kg/13 lbs. per stay 373.66.660 

B 8 kg/18 lbs. per stay 373.66.661 


Please order mounting brackets separately 

(choose from available options below) 


(for attachment to side panel of cabinet) 


Mounting distance 

from front edge nickel-plated 

28 mm (1 1 /8") 373.66.693 

37 mm (1 7 /16") 373.66.694 


Door mounting bracket 

For wood or aluminum frames over 35 mm (1 3 /8") 

profile wide 






For aluminum frames up to 35 mm (1 3 /8") profile wide 








32 (1 1/4") 

176 (6 15/16") 

Lid/Flap Stay 

Duo 

• Two stays are recommended 

for any door 600 mm (24") 

or wider 

• Units may need to be 

re-adjusted after the first 300 

cycles to maintain optimum 

performance. This is a one time 

adjustment that does not have 

to be repeated 

28/37 (1 1/8"/1 1/4") 

32 (1 1/4") 

32 (1 1/4") 

167 (6 9/16") 

221 (8 11/16") 

Hex Key, 4 mm 

142 32 (1 1/4") 

(5 9/16") 

max. 400 

(16") 

28/37 (1 1/8"/1 1/4") 

28/37 (1 1/8"/1 1/4") 


90° 

90° 

32 (1 1/4") 

192 (7 9/16") 

max. 600 

(24") 

90° 

229 (9") 

32 (1 1/4") 

min. 365 

(14 3/8") 

max. 600 

(24") 

Cat. No. 

008.28.044 

19 (3/4") 

32 (1 1/4") 

A 

Version A 

Sample measurements table for max. flap weight 

Flap max. flap weight lbs. 

height Stopping function Braking function 

inches 1 Stay 2 Stays 1 Stay 2 Stays 

For opening angle 75° 

8” 19.8 lbs 39.6 lbs 25.3 lbs 39.6 lbs 

10” 15.4 lbs 39.6 lbs 19.8 lbs 39.6 lbs 

12” 13.2 lbs 26.4 lbs 16.5 lbs 39.6 lbs 

14” 11 lbs 22 lbs 14.3 lbs 28.6 lbs 

16” 9.9 lbs 19.8 lbs 13.2 lbs 25.3 lbs 

17 1/2” 8.8 lbs 17.6 lbs 11 lbs 22 lbs 

19 1/2” 7.7 lbs 15.4 lbs 9.9 lbs 19.8 lbs 


8” 16.5 lbs 39.6 lbs 20.9 lbs 39.6 lbs 

10” 13.2 lbs 26.4 lbs 16.5 lbs 39.6 lbs 

12” 11 lbs 22 lbs 13.2 lbs 28.6 lbs 

14” 8.8 lbs 18.7 lbs 12.1 lbs 24.2 lbs 

16” 7.7 lbs 15.4 lbs 11 lbs 22 lbs 

17 1/2” 7.7 lbs 14.3 lbs 8.8 lbs 18.7 lbs 

19 1/2” 6.6 lbs 13.2 lbs 8.8 lbs 17.6 lbs 


8” 13.2 lbs 26.4 lbs 17.6 lbs 39.6 lbs 

10” 11 lbs 20.9 lbs 13.2 lbs 26.4 lbs 

12” 8.8 lbs 17.6 lbs 11 lbs 22 lbs 

14” 6.6 lbs 15.4 lbs 8.8 lbs 19.8 lbs 

16” 6.6 lbs 13.2 lbs 8.8 lbs 16.5 lbs 

17 1/2” 5.5 lbs 11 lbs 7.7 lbs 15.4 lbs 

19 1/2” 4.4 lbs 11 lbs 6.6 lbs 13.2 lbs 

12.7 

(1/2”) 


Installation Version A Installation Version B 

C 

Opening 

angle 

Distance from edge 

28/37 (1 1/8"/1 1/4") 

Lid Stay 

Opening Dimension Dimension 

Angle A C 

75° 192 (7 9/16”) 148 (5 13/16”) 

90° 192 (7 9/16”) 106 (4 3/16”) 

110° 160 (6 5/16”) 108 (4 1/4”) 


19 (3/4") 

32 (1 1/4") 

A 


Version B 

Sample measurements table for max. flap weight 

Flap max. flap weight lbs. 

height Stopping function Braking function 

inches 1 Stay 2 Stays 1 Stay 2 Stays 


8” 30.8 lbs 39.6 lbs 39.6 lbs 39.6 lbs 

10” 25.3 lbs 39.6 lbs 39.6 lbs 39.6 lbs 

12” 19.8 lbs 39.6 lbs 26.4 lbs 39.6 lbs 

14” 17.6 lbs 39.6 lbs 24.2 lbs 39.6 lbs 

16” 15.4 lbs 30.8 lbs 19.8 lbs 39.6 lbs 

17 1/2” 13.2 lbs 27.5 lbs 17.6 lbs 39.6 lbs 

19 1/2” 12.1 lbs 24.2 lbs 15.4 lbs 39.6 lbs 

21 1/2” 11 lbs 22 lbs 14.3 lbs 28.6 lbs 

23 1/2” 11 lbs 20.9 lbs 13.2 lbs 26.4 lbs 

25 1/2” 8.8 lbs 18.7 lbs 12.1 lbs 24.2 lbs 

27 1/2” 8.8 lbs 17.6 lbs 11 lbs 23.1 lbs 


8” 26.4 lbs 39.6 lbs 39.6 lbs 39.6 lbs 

10” 20.9 lbs 39.6 lbs 26.4 lbs 39.6 lbs 

12” 17.6 lbs 39.6 lbs 22 lbs 39.6 lbs 

14” 15.4 lbs 29.7 lbs 19.8 lbs 39.6 lbs 

16” 13.2 lbs 26.4 lbs 17.6 lbs 39.6 lbs 

17 1/2” 11 lbs 24.2 lbs 15.4 lbs 30.8 lbs 

19 1/2” 11 lbs 20.9 lbs 13.2 lbs 26.4 lbs 

21 1/2” 8.8 lbs 18.7 lbs 12.1 lbs 24.2 lbs 

23 1/2” 8.8 lbs 17.6 lbs 11 lbs 22 lbs 

25 1/2” 7.7 lbs 15.4 lbs 11 lbs 20.9 lbs 

27 1/2” 6.6 lbs 15.4 lbs 8.8 lbs 19.8 lbs 


8” 20.9 lbs 39.6 lbs 27.5 lbs 39.6 lbs 

10” 16.5 lbs 39.6 lbs 22 lbs 39.6 lbs 

12” 14.3 lbs 27.5 lbs 17.6 lbs 39.6 lbs 

14” 12.1 lbs 24.2 lbs 15.4 lbs 30.8 lbs 

16” 9.9 lbs 20.9 lbs 13.2 lbs 27.5 lbs 

17 1/2” 8.8 lbs 18.7 lbs 12.1 lbs 24.2 lbs 

19 1/2” 8.8 lbs 16.5 lbs 11 lbs 22 lbs 

21 1/2” 7.7 lbs 15.4 lbs 8.8 lbs 19.8 lbs 

23 1/2” 6.6 lbs 13.2 lbs 8.8 lbs 17.6 lbs 

25 1/2” 6.6 lbs 12.1 lbs 8.8 lbs 16.5 lbs 

27 1/2” 6.6 lbs 11 lbs 7.7 lbs 15.4 lbs 

C 

Opening 

angle 

Distance from edge 

28/37 (1 1/8"/1 1/4") 

Lid Stay 

Opening Dimension Dimension 

Angle A C 

75° 256 (10 1/16”) 212 (8 3/8”) 

90° 224 (8 13/16”) 182 (7 3/16”) 

110° 199 (7 13/16”) 154 (6 1/16”) 



472

Lid Stay 

Heavy Duty – MAXI 

• For wood or aluminum doors 

• Maximum opening angle 110º 

• Clip mounting without tools on pre-mounted bracket 

• Trial mounting is recommended 

• Adjustable by the means of a 10 mm ( 3 /8”) hex key, 

(not included, see below) 

• Left or right mounted 

• 110º concealed hinges and mounting plates are required for 

installation (not included) see pages 370–371, 380–384 

19 

(3/4”) 

(A) 

32 (1 1/4”) 

17 

(11/16”) 

18 

(11/16”) 

33 

(1 5/15”) 



Wood door mounting 

473 

6.3 

(1/4”) 

45 

(1 3/4") 

32 

(1 1/4") 

27 

(1 1/16”) 

28/37 

(C) 

Mounting Brackets (required) 

32 

(1 1/4”) 

12 

(1/2") 

18 

(11/16") 

4.2 

(5/32") 

8 

(5/16”) 

16 

(5/8”) 

19.5 

(3/4”) 

Opening 

Angle 

32 

(1 1/4”) 

45 

(1 3/4”) 

19 

(3/4”) 

(A) 

32 (1 1/4”) 

Aluminum door mounting 



28/37 

Opening 

Angle 

Distance from edge nickel-plated 

28 mm (1 1 /8") 373.69.907 

37 mm (1 7 /16") 373.69.906 


Door mounting bracket wood/aluminum 

For wood or aluminum door/frames over 

35 mm (1 3 /8") wide. 


Flat Head 

#6 




Door mounting bracket for aluminum frame 

For use with 563.55.931, 563.55.031 and 

563.55.911 frames are page 486. 


5.5 

(1/4”) 

Flat Head 

#6 




(C) 

16 

(5/8”) 

Hex key 


zinc-plated 

10 mm ( 3 /8”) 008.28.100 


Strength Required 

VARIANTA 

5 


Lid stay - Unhanded 

(cabinet mounting bracket sold separately, see below) 


Version nickel-plated 

B (see chart below) 373.69.900 

C (see chart below) 373.69.901 


Opening 

Angle 

Dimension 

A 

Dimension C 

Wood Aluminum 

doors doors 

75º 224 (8 13 /16") 207 (8 1 /8") 199 (7 13 /16") 

90º 192 (7 9 /16") 185 (7 5 /16") 172 (6 3 /4") 

110º 192 (7 9 /16") 145 (5 11 /16") 133 (5 1 /4") 

Version B 

Door 

Height 

Max. door weight in lbs. 

Opening angle 

75º 90º 110º 

300 (11 13 /16") 14.7 - 30.2 11.2 - 22.5 8.6 - 16.5 

400 (15 3 /4") 11.0 - 22.7 8.4 - 16.8 6.4 - 12.3 

500 (19 11 /16") 9.0 - 18.3 6.8 - 13.4 5.3 - 9.9 

600 (23 5 /8") 7.3 - 15.4 5.7 - 11.2 4.2 - 8.4 

700 (27 9 /16") 6.2 - 12.6 4.6 - 9.3 3.7 - 6.8 

800 (31 1 /2") 5.5 - 11.2 4.2 - 8.6 3.1 - 6.2 

900 (35 7 /16") 4.9 - 10.1 3.7 - 7.5 2.9 - 5.5 

1000 (39 3 /8") 4.4 - 9.0 3.3 - 6.6 2.4 - 4.9 

Weight chart is based on one lid stay. 

Version C 

Door 

Height 

Max. door weight in lbs. 

Opening angle 

75º 90º 110º 

300 (11 13 /16") 26.2 - 46.2 20.0 - 34.8 15.0 - 25.6 

400 (15 3 /4") 19.6 - 34.8 15.2 - 26.2 11.2 - 19.2 

500 (19 11 /16") 15.9 - 27.6 12.1 - 21.2 8.8 - 15.7 

600 (23 5 /8") 13.0 - 23.4 10.1 - 17.4 7.3 - 13.0 

700 (27 9 /16") 11.0 - 19.4 8.4 - 14.6 6.4 - 10.6 

800 (31 1 /2") 9.7 - 17.4 7.5 - 13.0 5.7 - 9.5 

900 (35 7 /16") 8.8 - 15.4 6.6 - 11.5 5.1 - 8.4 

1000 (39 3 /8") 7.9 - 13.9 5.9 - 10.4 4.4 - 7.7 






Lid Stay 

105 

• Spring tension adjustable with Pozi drive #2 

• Mounting bracket sold separately 

• Maximum opening angle 105° 

• The lid remains open at the position at which it is released, at any position above 45º 

• Overlay from 12 mm (1/2") to 17 mm (11/16") 


• Concealed hinges and mounting plates are required for installation (not included), 

see pages 370–371, 380–384 

• Aluminum Frames are on page 486 

cabinet drilling door drilling - wood 

21* 32 

top panel 

side wall 

27* 20 

*Tolerance of ±2mm. 

2xM4 

32 

top panel 

C 

side wall 

A B 

2x ø5 / 8 deep 

for pin 

door drilling - aluminum frame 

3.2 

aluminum frame door 

Flat Head 

#8 

11+ 

overlay 



side wall 

32 

top panel 

C 

wood door 

Flat Head 

#6 



Type of Use Hinge Type Dimension A Dimension B Dimension C 

wood doors 2 164 mm (6 7 /16") 169 mm (6 5 /8") 113 mm (4 11 /16") 

aluminum frames 2 169 mm (6 5 /8") 174 mm (6 7 /8") 118 mm (4 5 /8") 

*Dimensions A and B to be equally changed according to other mounting plate heights. 

Chart based on 19mm (3/4”) particle board. 

No. of 

Fittings 

Lid 

Height 

Lid 

Weight 

without handle in kg with small handle with large handle* 

mm inches kg. lbs. min. max. min. max. 

1 300 (11 11 /16") 1.6 - 4.3 (3.5 - 9.5) 500 to 1100 350 to 750 

2 300 (11 11 /16") 3.2 - 8.6 (7 - 18.9) 1000 to 2300 700 to 1500 

1 350 (13 11 /16") 1.3 - 4.1 (2.8 - 9) 350 to 900 250 to 600 

2 350 (13 11 /16") 2.6 - 8.1 (5.7 - 17.8) 700 to 1850 550 to 1200 

1 400 (15 11 /16") 1.3 - 3.4 (2.8 - 7.5) 275 to 650 250 to 500 

2 400 (15 11 /16") 2.5 - 6.8 (5.5 - 15) 550 to 1300 400 to 1000 

1 450 (17 11 /16") 1.2 - 3.1 (2.6 - 6.8) 250 to 550 250 to 375 

2 450 (17 11 /16") 2.4 - 6.1 (5.2 - 13.4) 400 to 1100 325 to 750 

1 500 (19 11 /16") 1.1 - 2.9 (2.4 - 6.4) 250 to 450 250 to 300 

2 500 (19 11 Door Width in mm 

/16") 2.2 - 5.8 (4.8 - 12.7) 350 to 900 300 to 600 

*Large handle assumed weight: 0.1 kg per 100 mm cabinet width. 

Lid Stay 

Length: 280 mm (11 1 /16”) 

Material: zinc; Cover: plastic 

nickel-plated 

left 373.77.302 

right 373.77.301 


Mounting bracket for wood doors 





Mounting bracket for aluminum doors 







474

Lid Stay 

E-Z Open 

• For wood or aluminum doors 

• Can be used for a face frame application 

• Smooth motion and stopping 

• Secure holding in open and closed positions 

• 110º concealed hinges and mounting plates are 

required for installation, see pages 370–371, 380–384 

• Aluminum Frames are on page 486 

Spring 

Door bracket 



475 

80 ( 1/8") 

14 (1/2”) 

14 

(1/2”) 

Rod 

Ø 6 (1/4”) 

32 

(1 1/4”) 

46 

(1 7/8”) 

Door 

height 

15 

(5/8”) 

233 

(9 3/16”) 

19 

(3/4”) 

46 

(1 7/8”) 

32 

(1 1/4”) 

Hinge 

Center 

Door mounting bracket (optional) 

For aluminum frame profiles of less 

than 35 mm (1 3/8") wide. 

Recommended for aluminum 

frames series 563.00, 563.01, and 

563.04. 

Cat. No. 

373.70.900 


235 (9 1/4") 

Cabinet bracket 

67 

(2 5/8”) 

19 (3/4”) 

ca. 90º 

32 

(1 1/4”) 

46 

(1 7/8”) 

Frameless 

Door in 

open position 

Door in closed position 

31 

(1 1/4”) 

Door 

height 

233 

(9 3/16”) 

Hinge 

Center 

58.5 

(2 5/16”) 

44.5 

(1 3/4”) 

Face 

Frame 


Lid stay 100 N (22 1/2 lbs.) 

For wood doors or aluminum frames of 

35 mm (1 3/8") profile width or wider 



silver 373.71.901 

Packing: 30 sets (1 set = 2 springs, 2 cabinet 

brackets, and 2 door brackets.) 

Lid stay 150 N (33.7 lbs.) 

For wood doors or aluminum frames of 

35 mm (1 3/8") profile width or wider 



silver 373.71.902 

Packing: 30 sets (1 set = 2 springs, 2 cabinet 

brackets, and 2 door brackets.) 

Door in open position 

88±2º 

Flat Head 

#6 

Face Frame 

Door in closed position 

Door 

Door Weight 

height 2 – 3 kg. 3.5 – 4.5 kg. 5 – 6 kg. 6.5 – 9 kg. 

mm inch 5 – 7 lbs. 8 – 10 lbs. 11 – 13 lbs. 14 – 20 lbs. 

254–305 (10-12") 373.71.901 373.71.901 373.71.901 373.71.902 

330–380 (13-15") 373.71.901 373.71.901 373.71.901 –– 

406–457 (16-18") 373.71.901 373.71.901 373.71.902 –– 

483–533 (19-21") 373.71.901 373.71.902 –– –– 

559–610 (22-24") 373.71.901 373.71.902 –– –– 

The values indicated are guidelines only. Trial application is recommended. Guidelines 

are based on two lid stays per door. 





Lid Stay 

15 

• The flap remains open at the position at which it is released, up to a 

maximum opening angle of 110º, wide enough to allow for 

optimal access as well as easy closure 

• Mounted on the cabinet side walls, independent of the top shelf 

• High quality galvanized finish ensures maximum rust prevention 

• Top shelf thickness minimum 16 mm ( 5 /8”), maximum 20 mm ( 13 /16”) for installation 

20 

max. 

Door 

2 

10 

128 

A 

16-20 

80 

64 

VARIANTA 

5 

Side 

Panel 



B 

24 

35 

38 

64 

Pan Head 

#8 



Material: steel; Housing: plastic 

Discontinued 

Finish/Colour Cat. No. 

nickel-plated/white [372.46.700] 

nickel-plated/silver RAL 9006 [372.46.200] 

Packing: 1 set (1 pair of fittings, left and right, 1 pair of plastic covers, 

2 green springs, 2 orange springs and 2 white springs) 

White 

Orange 

Range of Use and Types of Springs 

The wide adjustment range of the 

springs makes it possible to use the 

fitting for flaps of the same size but of 

different material or thickness. 

For installation: 2 springs, 1 for each 

side is required. 

Width B 

Height A 400 500 600 700 800 900 1000 1100 1200 

300 green green white white white white orange orange orange 

350 green white white white white orange orange orange** orange** 

400 white white white white white orange** orange** 

450 white white orange orange orange 

500 white orange orange orange** orange** 

550 white orange orange** 

600 orange orange** 

* Very light flaps of these dimensions (for example, solid pine doors or wooden frame doors) might slowly move 

in an upward direction from opening angles of about 30 to 70º independently. If this is not desired, please attach 

weak springs (green marks). 

** The use of very heavy flaps of these dimensions (for example, MDF) leads to a borderline functioning of the 

fitting. (This is, for example, dependent upon the exact position and the weight). Trial mounting is recommended. 

Green 




476

Swing-Up Fittings 

Frontlift, Adjustable 

• Doors swing up automatically when lifted and are securely held open 

• Self operating from 17º 

• The spring action holds doors tight when closed 

10 

(3/8") 

64 (2 1/2") 



477 

120 

(4 3/4") 

78 

(3") 128 

14 (9/16") 

(5") 

Swing-up Hinge, Swingtop II 

min. 220 

(8 5/8") 

210 (8 1/4") for 

13 mm (9/16") 

overlay 

64 (2 1/2") 

32 (1 1/4") 

min. 

320 

(12 5/8") 

Door Angle, 75º or… 


• Provides hidden installation of small appliances in cabinets 

• Amount of upward travel = 380 mm (15”) 

Max. Internal Min. Internal Max. Front white RAL 

Cabinet width Cabinet width Panel weight 9010 

570 mm (22 3 / 8") 411 mm (16 3 / 16") 4 kg (8.8 lb) 372.42.700 

870 mm (34 1 / 4") 561 mm (22 1 Material: steel 


/ 16") 5 kg (11 lb) 372.59.702 

Material: steel, epoxy-coated 

Spring: steel 

Stop: plastic 

left 

with adjustable spring 

right 

nickel-plated/white 

372.49.701 

372.49.700 

without spring 


left only 372.49.790 


37 

22 

64 

32 



Swing-up Fitting 

• Adjusted to individual cabinet widths, by cutting the 

aluminium cross bar to the desired length 

• For assembly on wood doors or aluminum frames 

• For microwave, upper cabinets 

• Concealed front panel fixing 

• Amount of upward travel = 380 mm (15”) 

• Aluminum frames are on page 486 

120 

(4 3/4") 

± 3 mm 


min. 

320 

min. 

220 


Swing-up Fitting for wood or aluminum doors with frames 35 mm(1 3 /8 ”) or wider 

Minimum internal cabinet width: 450 mm (17 3 36 

/4”) 


Max. internal Max. 

cabinet front panel Piston 

width B weight Strength white silver RAL 9006 

870 mm 5.0 kg (11 lbs.) 250 N 372.51.722 372.51.222 

1170 mm 7.0 kg (15.4 lbs.) 320 N 372.51.732 372.51.232 

1470 mm 


8.5 kg (18.7 lbs.) 380 N 372.51.742 372.51.242 

min. 

320 

B 

B 

60 

± 1 mm 

min. 

220 

± 1.5 mm 

Swing-up Fitting for aluminum frames less than 35 mm(1 3 /8”)wide 

Minimum internal cabinet width: 450 mm (17 3 

/4”) 


Max. internal Max. aluminum 

cabinet front panel Piston silver 

width B weight Strength RAL 9006 

870 mm 5.0 kg (11 lbs.) 250 N 372.51.272 

1170 mm 7.0 kg (15.4 lbs.) 320 N 372.51.282 

1470 mm 


8.5 kg (18.7 lbs.) 380 N 372.51.292 

60 



478

Swing-Up Fitting - Slide 

• For wood or aluminum frame doors 

• The door remains open at the position at which it is released 

• Adjustable with a 3 mm and 10 mm hex key, supplied 

• Door mounting bracket and assembly rod sold separately 

• Calculation to cut assembly rod: inside cabinet width less 

25 mm (1") = the desired length 

• Each fitting is 7/8” thick 

Cabinet drilling 

122.5 

(4 13/16") 

80.5 

(3 3/16") 



479 

101.5 

(4") 

37.5 

(1 1/2") 

206.5 

(8 1/8") 

21.5 

(7/8") 

86.5 

(3 3/8") 

15 

(9/16") 

37 

(1 7/16") 

27 

(1 1/16") 

6.0 

(1/4") 

40 

(1 9/16") 

4.5 

(3/16") 

Ø18 

(11/16") 

19 

(3/4") 

254 (10”) min. 

cabinet depth 

110 

(4 5/16") 

32 32 32 

(1 1/4") (1 1/4") (1 1/4") 

110 

(4 5/16") 

32 32 32 

(1 1/4") (1 1/4") (1 1/4") 

157-251.5* 

(6 3/16")-(9 7/8") 

*Depending on door height. 

15 

(9/16") 

24 

(15/16") 


Swing up fitting 


Housing: plastic, grey RAL 9006 

grey 

Door height Weight capacity (lbs.) RAL 9006 

350 - 400 7.9 - 10.1 372.67.201 

(13 3/4" - 15 3/4") 10.4 - 12.6 372.67.202 

Amount of 

upward travel 

336 mm 

(13 1/4”) 

12.8 - 15.4 372.67.203 

15.7 - 20.1 372.67.204 

20.3 - 26.0 372.67.205 

380 - 500 10.6 - 13.2 372.67.211 

(15" - 19 11/16") 13.5 - 16.8 372.67.212 

Travel = 380 mm 

(15”) 

16.9 - 21.6 372.67.213 

21.8 - 25.1 372.67.214 

25.3 - 32.1 372.67.215 

Travel 450 = - 472 580mm 10.3 - 13.0 372.67.221 

(17 3/4" - (18 22 1/2”) 3/4") 13.2 - 16.7 372.67.222 

16.9 - 20.2 372.67.223 

20.5 - 25.5 372.67.224 

550 - 660 11.7 - 14.5 372.67.231 

(21 3/4" - 26") 

Travel = 531 mm 

14.7 - 17.4 372.67.232 

(21”) 17.6 - 22.7 372.67.233 

Packing: 5 pcs. (1 pc. = 1 left arm, 1 right arm, one 

10 mm hex key, one 3 mm hex key, and mounting 

instructions) 

Door mounting bracket (required) 

For wood or aluminum frame doors with a 

profile length 35 mm (1 3 /8") or wider 


Pan Head 

#8 

VARIANTA 

5 




Door mounting bracket (required) 

For aluminum frame doors with a profile less than 

35 mm (1 3 /8") 

Material: zinc/steel 




Assembly rod (required) 

Material: aluminum, anodized 

Door width Length Cat. No. 

600 (23 5 /8") 537 (21 1 /8") 372.67.980 

900 (35 7 /16") 837 (32 15 /16") 372.67.981 

1200 (47 1 /4") 1137 (44 3 /4") 372.67.982 







Folding Door Fitting 

• For wood or aluminum frame doors 

• Door stays open in any position 

• 120º concealed hinges and plates are required for installation 

(sold separately, see pages 370–371, 380–384) 

• Handle can be mounted 1 1/2" from the edge of the bottom door 

• Door panels must be equal in height 

• Safety feature - middle hinges break away to prevent injury from jammed fingers 

249 

(9 13/16") 

56 

(2 3/16") 

Middle door hinge – with safety feature 

Two required per door. For doors over 900 mm 

(35 3 /8") three are required. 


Cat. No. 

372.64.790 


30 

32 

18 

(11/16") 

32 

(1 1/4") 

32 

(1 1/4") 

min. 38 (1 1/2”) 

from bottom edge 

21 (13/16") 



Swing-up fitting 

Material: steel, powder coated 

Cover cap: plastic 

Cabinet Combined grey 

height door wt.(lbs) RAL 9006 

590 - 630 13.2 - 14.8 right 372.64.701 

(23 1 /4" - 24 13 /16") left 372.64.702 

15 - 17.9 right 372.64.703 

left 372.64.704 

18 - 23.1 right 372.64.705 

left 372.64.706 

23.3 - 29.5 right 372.64.707 

left 372.64.708 

29.7 - 35.7 right 372.64.709 

left 372.64.710 

700 - 750 11.7 - 14.3 right 372.64.721 

(27 9 /16" - 29 1 /2") left 372.64.722 

14.6 - 19.2 right 372.64.723 

left 372.64.724 

19.4 - 24.3 right 372.64.725 

left 372.64.726 

24.5 - 29.3 right 372.64.727 

left 372.64.728 

29.5 - 32.6 right 372.64.729 

left 372.64.730 

780 - 840 11 - 13.4 right 372.64.741 

(30 11 /16" - 33 1 /16") left 372.64.742 

13.7 - 17.6 right 372.64.743 

left 372.64.744 

18 - 22.9 right 372.64.745 

left 372.64.746 

23.1 - 27.6 right 372.64.747 

left 372.64.748 

27.8 - 29.8 right 372.64.749 

left 372.64.750 

Packing: 10 pcs. (Includes mounting instructions) 


for wood or aluminum frame doors 35 mm (1 3 /8") 

or more 

Material: steel, nickel-plated, plastic 


right grey-white RAL 9002 372.64.771 

left grey-white RAL 9002 372.64.772 



for aluminum frame doors 35 mm (1 3 /8") or less 

Material: steel, nickel-plated, plastic 


right grey-white RAL 9002 372.64.781 

left grey-white RAL 9002 372.64.782 




480

Flipper Door 

Easy-Down – Accuride Model 1155 

• The Easy-Down requires few or no cabinet modifications, and is easy to install 

• Door closing speed remains similar on light and heavy doors 

• Increases safety in the home or workplace by slowing the speed and dampening 

overhead doors as they close 

• Internal mounting allows cabinets to be positioned side to side 

• Only one pair needed for doors up to 48" wide; no adjustments necessary to the 

closure mechanisms 

• Mounting brackets are included and recommended when particle board is used 

4.6 x 5.3 (2x) 

(3/16” x 7/32”) 

11.1 

(7/16”) 

88.9 

(3 1/2”) 

Hinge shown 

in closed position 

.71±.04 

(1/32”±0) 

Ø5.2 (2x) 

(7/32”) 

59.9 

(2 3/8”) 

5.2 x 12.7 (2x) 

(3/16” x 1/2”) 



481 

18.3 

(3/4”) 

19.1 

(3/4”) 

12.7 

(1/2”) 

46 

(1 13/16”) 

10.2 

[7/16”] 

32.8 

(1 5/16”) 

1.0 (1/16”) ref. 

Cylinder Cover 

Cover shown attached to cylinder. 

128 

(5 1/16”) 

Optional bracket shown 

Ø4.6 (2x) 

(3/16”) 

9.7 

(3/8”) 

Cover shown attached to cylinder 

Slide Length 

Slide Travel 

4.6 x 9.5 (2x) 

(3/16” x 3/8”) 

25.4 (1”) 

12.7 

(1/2”) 

4.6 x 5.3 (2x) 

(3/16” x 7/32”) 

19.1 

(3/4”) 

2.3 (1/8”) ref. 


Slide length Slide travel Cat. No. 

inch mm inch mm black 

12 303 75 ⁄8” 194 408.22.331 

14 354 95 ⁄8” 245 408.22.336 

16 405 115 ⁄8” 296 408.22.341 

18 456 135 ⁄8” 346 408.22.346 

20 507 155 ⁄8” 397 408.22.351 

22 557 175 ⁄8” 448 408.22.356 

24 608 195 Easy-down flipper door slide for wood applications 

• capacity up to 14 kg (30 lbs.)/pair, doors up to 48” wide 

• doors open over the top of cabinet 


⁄8” 499 408.22.361 

Packing: 2 pair (includes 4 slides, 4 cylinder covers, 

8 clip-on brackets, and mounting screws) 

9.7 (3/8”) 

Ø6.4 (8x) 

(1/4”) 




Quick Door Aluminum Door Frames 

Cut-To-Size 

• Easy to assemble aluminum door that 

requires no special drilling for the hinges 

• To be used with glass or panels with a 

thickness of 4 mm (1/8” to 5/32”) 

Front 

1. Mitre the ends 45º. 

Mitred Profile 

Corner 

Connector 

Concealed 

Hinges 

2. Slide the brackets into the 

ends. 



Inside aluminum door profile 

please order 

profiles separately 

3. Slide the hinges into the 

sides. 

please order 

decorative profiles 

separately 



482

H-Series Hinges for Aluminum Door Frames 


Given the factors: 

• What is the desired opening angle? 

• What is the hinge arm type? 

• If not, what is the side panel thickness? 

• What is the door thickness, size and weight? 

• How will the hinge be mounted to the door– 

(Screw-mount or press-fit)? 

• What is the mounting plate thickness? 

• What is the tab? 

Use the following formula to determine overlay: 

Hinge type minus mounting plate type plus tab* = overlay 

* For aluminum profile doors only, always use 3 mm. 



There is no hard and fast rule which applies. When determining the number 

of hinges needed, the main factors to consider are door size and weight. 

A trial mounting is advisable in case of any doubt, such as with doors 

supporting mirrors, or unusually wide doors. Avoid disproportionate door 

width/height ratios. Use this table for standard, conventional-material 

doors. When in doubt, always allow for an extra hinge. 

• For commercial and heavy duty applications, see Häfele’s Prämatic 

(page ?) and Advantage 5k hinges (page ?). 



483 

Hinge Type 17 



Tab 

Door 

Hinge Type 8 


overlay doors 

Center Centre 

panel 

Door Door 

Tab 

Door 

width 

(mm) 

2500 (98 7/16") 

2000 (78 3/4") 

1500 (59 1/16") 

1000 (39 3/8") 

500 (19 11/16") 

Door 

height 

(mm) 

No. of hinges 


Hinge Type 0 





Twin Mounting 



Full overlay (A) 17 - 5 + 3 = 15 

Half overlay (B) 8 - 5 + 3 = 6 

Inset (C) 0 - 2 + 3 = *1 

*Adjust to 0 overlay using side adjustment. 

If there is no mounting plate with the required reinforcement, the gap must be altered. 


2 

Side 

Weight approx. (in kg) 

4 - 5 6 - 9 10 - 15 

500 

500 500 

3 4 

Tab 

Door 



Full overlay (A) 17 - 2 + 3 = 18 

Half overlay (B) 8 - 2 + 3 = 9 

Inset (C) 0 - 2 + 3 = *1 



Quick Door Aluminum Frame Profiles 

Cut-To-Size 

• Easy fabrication, only a 45º mitre cut is needed 

• Ability to make individually sized frames 

• Aluminum saw blade recommended for mitre cut 

• No drilling required - hinges slide into aluminum profile 

21 

24 

21 

14 

14 

14 

6.5 

6.5 

38 

6.5 

38 

23 

4 

4 

please order 


separately 

9.5 

please order 

plastic gasket 


please order 


separately 

9.5 

please order 



please order 


separately 

4 

9.5 

please order 





Aluminum frame profile 

for glass thickness: 4 mm (1/8” - 5/32”) 



silver coloured anodized 563.25.901 

Packing: 1 pc. [2.5 m (8' 2 7 / 16")] 

Glass size - 34 mm less height and width of 

aluminum frame. 






Packing: 1 pc. [2.5 m (8' 2 7 / 16")] 


aluminum frame. 






Packing: 1 pc. [2.5 m (8' 2 7 / 16")] 


aluminum frame 

• Decorative profiles and plastic gasket on next page 



484

Quick Door Aluminum Frame 

Cut-To-Size – Door Hinges and Accessories 

• No drilling required 

• Pre-attached slotted screws secure hinge to aluminum frame 

H-Series Hinges 

Flanged mounting plates in two pieces, screw-mounted (also in series-drilled holes) 



485 

VARIANTA 

3 

VARIANTA 

5 

Drilling 

diagram 

Face frame mounting plates, screw-mounted 

37 

Drilling 

diagram 

12 

32 

32 

37 


110º Hinge 

Mounting Hinge arm Hinge type Cat. No. 

Full overlay 18 563.25.940 

Half overlay 9 563.25.941 

Inset 

mounting 


1 563.25.942 

3 or 5 

32 

32 

• With pre-installed hinge-arm 

retaining screw 

Plastic gasket profile, for glass or panel inserts 

For glass panel thickness of 3 mm (1/8”) to 

4 mm 5/32”) and 4 mm (5/32”) to 5 mm (3/16”). 

Insert into frame before mounting the glass panels. 


Cat. No. 

transparent 563.25.921 

Packing: 300 pcs. (2.5 meters) 

Decorative profile, for mounting on inside of door 

frame of aluminum profile. 




Packing: 1 pc. (2.5 meters) 

Corner connector, with clamping screws for 

aluminum frame profiles to connect mitres. 




Packing: 250 pcs. (4 pcs. required per frame) 

• With pre-installed hinge-arm retaining screws 

Edge spacing 37 mm 

With vertical adjustment (via screw ± 2 mm) 


Mounting VP type nickel-plated matt 

4 mm 4 316.52.544 

6 mm 


6 316.52.546 

Flat Head 

#8 

With vertical adjustment (oblong holes) 


Preinstalled 

retaining 

screw 

Face frame 

Wing mounting 

plate 

Mounting Reinforcement type nickel-plated matt 

5/8" overlay 6 mm 6 316.94.606 

1/2" overlay 


10 mm 10 316.94.610 

Side or 

center 

panel 






Quick Door Aluminum Frame Doors 

Custom Order For Hinged Doors 

Specification: 

• Select frame profile 

• Select glass 

• Hinge type and overlay 

• Provide details and dimensions on hinge sizes and drilling locations 

• Hinged doors: Hinge attachment through machined cutouts 

Front 

Front 

Front 

19.5 

(3/4") 

20.5 

(13/16") 

20.6 

(13/16") 

22.3 

(7/8") 

20.5 

(13/16") 

23 

(15/16") 

19 

(3/4") 

50 

(1 31/32") 

Front 

45 

(1 3/4") 

54 

(2 1/8") 

Front 

Special metal profile 

hinge suitable for 

aluminum profile, 

see page 

488. 

14 

16.5 

28 32.1 



Profile 19.5 x 23 mm (3/4" x 15/16") 



anodized, matt 563.55.931 

brushed stainless steel 563.55.031 


Profile 20.5 x 19 mm (13/16" x 3/4") 





Profile 20.6 x 50 mm (13/16" x 1 31/32") 





Profile 22.3 x 45 mm (7/8" x 1 3/4") 






Profile 20.5 x 54 mm (13/16" x 2 1/8") 






10 

6.9 1.2 

17.7 

45 

35 

9.5 

3-7 

min. 

12.5 

Standard cup hinge suitable 

for aluminum profile, see 

pages 380–384 



486

Quick Door Aluminum Framed Glass Doors 

Cut To Size – Custom Order Glass 

Specify glass for use with aluminum glass profiles 563.55, 563.56 series. 



487 

Clear Glass Acid Etch 

Quatrix Patterned Glass Listrel F Patterned Glass 

Soft Square Patterned Glass Screen Patterned Glass 





Duomatic Hinges for Aluminum Doors 

• Developed for use with metal profiles 

• A ø3.5 x 9.5 mm (#6 x 3/8”) countersunk sheet metal screw to attach hinge to frame is recommended 

• Corresponding mounting plates are on pages 382–387 

• To be used with aluminum glass doors are on page 486 


New 

Item 

14 

16.5 

17.7 

28 32.1 





Screw-mount, self-closing 


Mounting Hinge arm Hinge type nickel-plated 




10 

6.9 1.2 

Colour Cat. No. Packing 

white 329.18.700 5000 pcs. 

black 329.18.308 1000 pcs. 

Mounting Screws: 

Self-tapping sheet metal screw for attaching hardware 

to aluminum frame doors. 

Phillips #7 x 1/2", CSK with undercut head. 



Cat. No. 

010.94.902 



488

Door Bumpers 

• Quick setting, synthetic rubber-based adhesive 

• Manufactured with UV inhibitors to prevent yellowing over time 

• UL 94 HB Approved (polyurethane bumpers) 

Door Bumpers 



489 

Ø12.6 

Ø12.7 

ø 6.4 

ø 8.5 

Ø12.7 

10.2 

Ø12.7 

Ø9.5 

12.7 

10 

5 

3.8 

1.6 

2.2 

3.5 

2.5 

3.2 

3.8 

1.5 

3.0 


Silent Bumper 2 

• Designed for use with face frame hinges 

Material: 100% polyurethane 

Cat. No. 

transparent [356.25.480] 

Packing: 5,000 pcs. 

New 

Item 

Silent Bumper 

Softer material and 2-stage impact reduces physical 

force of impact by more than half 


Cat. No. 


Packing: 5,000 pcs. (1 sheet = 200 pcs.) 


Cat. No. 




Cat. No. 






brown 356.25.734 

Packing: [5,184] pcs. (1 sheet = [288] pcs.) Text 

Change 


Cat. No. 




Cat. No. 




Cat. No. 




Cat. No. 



Material: foam 

Colour Size Cat. No. 

brown [10] x 3.2 mm 356.25.121 

Packing: [43,200] pcs. (1 sheet = [216] pcs.) Text 

Change 




Door Bumpers and Trim Caps 

Door Bumper, press-fit 


transparent 

head height 1.5 mm 356.16.015 

head height 2 mm 356.16.020 

head height 2.5 mm 356.16.025 




Cat. No. 



Door Bumper, knock-in 

Door Bumper, press-fit, 6 mm dia. 




white 356.20.725 


3 

3.5 

Ø8 

Ø5 

Ø8 

Ø 8.5 

13.5 



white 356.39.706 


1.5 

Ø5 

Ø8 

Ø6 

8.5 

5.5 

8.5 



Trim Cap for hinge cup holes, 35 mm dia. 




Cat. No. 





white 356.20.707 



2 piece silent touch Ø8.5 



white 340.41.702 

brown 340.41.104 


2.5 

13.5 

35 

1.9 

Ø5 

Ø9 

Ø5 

Ø10 


Cat. No. 



8.5 

7 

38 

10 

0.5 



490

Concealed Hinges

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?