Leica TCS SP5 - ZMBH

More documents

Recommendations

Info

28 All safety devices, safety locks, and safety systems of the laser product must be in an operational state. Deactivating or damaging these safety devices or any intervention in any of these safety devices may lead to serious eye injuries, physical injuries or property damage. In these cases, Leica Microsystems CMS GmbH shall not assume any liability. The owner/operator is responsible for naming a laser safety officer or a laser protection advisor (according to the standard IEC/EN 60825-1: "Safety of laser products, Part 1: Classification of systems, requirements and user guidelines" and the respective national regulations). Repairs and servicing may only be performed by authorized Leica Microsystems CMS GmbH service personnel. The owner/operator is fully liable for all consequences resulting from the use of the system if it is opened, improperly serviced or repaired by persons other than authorized Leica service representatives. If repairs or service measures are performed that require opening parts of the housing, only trained Leica service technicians may occupy the room in which the system is located. Do not connect any external equipment or other components. Connect to the product only those electrical devices that are listed in the operating manual. Otherwise, please contact your local Leica service agency or Leica Microsystems CMS GmbH. Leica Microsystems CMS GmbH shall not be liable for damages resulting from nonobservance of the above information. The above information does not, in any way, implicitly or explicitly, modify the warranty and liability clauses contained in the general terms and conditions of Leica Microsystems CMS GmbH.
4.4 Safety Instructions for the User Read and observe the safety instructions in the operating manual and the safety labels located on the system. Failure to observe the safety instructions may lead to serious injuries and to significant damages to the system and loss of data. The instrument is a Class 3B or 4 laser product (depending on the laser used). This laser product may be operated only by persons who have been instructed in the use of the system and the potential hazards of laser radiation. Before carry out operating steps with the system for the first time, first read the corresponding description of the function in the online help. For an overview of the individual functions, refer to the table of contents of the online help. As it is impossible to anticipate every potential hazard, please be careful and apply common sense when operating this product. Observe all safety precautions relevant to Class 3B/IIIb lasers and Class 4/IV lasers for MP systems. Do not deviate from the operating and maintenance instructions provided herein. The failure to observe these instructions shall be exclusively at the operator's own risk and may void the warranty. 4.5 Operational Reliability This instrument must not be used together with life-support systems such as those found in intensive-care wards. This instrument may only be used with a grounded AC power supply. Contact with liquids or the entry of liquids into the housing must be avoided. 29
Page 1 and 2: Leica TCS SP5 Leica TCS SP5 X User
Page 3 and 4: Table of Contents 1. General ......
Page 5 and 6: 6.3.3 VIS and UV Systems with Inver
Page 7: 11.3 Cleaning the Microscope Surfac
Page 10 and 11: 1.2 About this Operating Manual Whe
Page 12 and 13: 2.2 TCS SP5 X system overview Figur
Page 14 and 15: 2.5 Patents The Leica TCS SP5 produ
Page 16 and 17: 2.7.1.3 TCS SP5 X with inverted mic
Page 18 and 19: 2.7.3 Requirements Regarding Ambien
Page 20 and 21: 20 The components for laser safety
Page 22 and 23: 2.8.3 Overview of Usable VIS/UV Las
Page 25 and 26: 3. Safety Instructions and their Me
Page 27: 4. General Safety Instructions 4.1
Page 31 and 32: 5. Safety Devices 5.1 Disconnecting
Page 33 and 34: The key switch for protection again
Page 35 and 36: Immediately disconnect the system f
Page 37 and 38: 5.6 Remote Interlock Connections on
Page 39 and 40: 5.9 Special Laser Safety Equipment
Page 41 and 42: 5.10 Safety labels on the system Th
Page 43 and 44: 5.10.2 Upright microscope DM 5000/6
Page 45 and 46: 5.10.3 Scan Head Angled front view
Page 47 and 48: 5.10.5 External UV laser 4 Figure 2
Page 49 and 50: 5.10.7 MP beam coupling unit Angled
Page 51: 5.10.9 Mirror Housing Front view of
Page 54 and 55: 54 Do not introduce any reflective
Page 56 and 57: 6.5 Changing Specimens 56 Never cha
Page 58 and 59: 6.7 Changing the Transmitted-Light
Page 60 and 61: 6.8 Mirror housing on upright micro
Page 62 and 63: 6.9 Changing Filter Cubes, Beam Spl
Page 64 and 65: Figure 41: Spacer on objective 64 P
Page 66 and 67: 66 Use your personal user ID if one
Page 68 and 69: 68 The power supply of the achromat
Page 70 and 71: 7.2 Starting the LAS AF 70 With the
Page 72 and 73: 7.3 Setting Up Users 72 The default
Page 74 and 75: 74 6. Shut down the computer. On th
Page 76 and 77: 9.2.2 Accessing the Online Help The
Page 78 and 79:
9.3 Structure of the graphical user
Page 81 and 82:
10. Introduction to Confocal Work 1
Page 83 and 84:
1 Filter cube 2 Specimen 3 Objectiv
Page 85 and 86:
10.1.3 Why Scan? Specimens must be
Page 87 and 88:
Out of focus in focus 1 2 3 Pinhole
Page 89 and 90:
work is required. Once all paramete
Page 91 and 92:
Figure 67: Selecting the illuminati
Page 93 and 94:
Exc Refl Exc1 Exc2 Em 1 Em 2 Em Fig
Page 95 and 96:
Figure 71: Optical sections with a
Page 97 and 98:
Numerical Aperture 1,4 1,25 0,4 Opt
Page 99 and 100:
Figure 74: Zoom, Pan and Rotation c
Page 101 and 102:
extremely sensitive specimens and i
Page 103 and 104:
Figure 78: Simultaneous scan of two
Page 105 and 106:
dominant, the selection of a differ
Page 107 and 108:
thicknesses between 0.5 µm and 2.5
Page 109 and 110:
10.4.5.3 Orthogonal Projections A f
Page 111 and 112:
imposed here by a number of factors
Page 113 and 114:
(measuring parameters) does not in
Page 115 and 116:
11. Care and Maintenance 11.1 Gener
Page 117 and 118:
12. Transport and Disposal 12.1 Cha
Page 119 and 120:
Curvature of Image Field The curved
Page 121 and 122:
Lambda Series Stack of individual i
Page 123 and 124:
Dry Objective A microscopic objecti
Page 125 and 126:
125
Page 127 and 128:
127
Page 129 and 130:
15.2 Declaration of conformity 129
Page 131 and 132:
131
show all

Leica TCS SP5 - ZMBH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?