Operation manual Track System TRUMPF 95 - Gerriets

More documents

Recommendations

Info

2 System Installation 2.3.1 TRUMPF 95: Motor Operation 30 For installation and operation see the corresponding motor operation manual. Art-No 3170 2031 (2061 / 2121 / 2991) Art-No 3115 9011 Art-No 3170 1011 (1021 / 1031 / 1041) Art-No 3170 4371 (4681 / 4951) Art-No 3115 7111 Art-No 3115 7121 TRAC-DRIVE Motor • 2-grooved pulley. • Automatic rope tensioning. • Different speeds and control functions available. • Track mounting with mounting bracket 3115 9011. • For use with rope up to Ø 8 mm. • Weight: 16.490 g. TRAC-DRIVE Mounting Bracket • For direct track mounting of TRAC-DRIVE or ROPE-DRIVE. • With 4 bolts, spacers and washers for mounting TRAC-DRIVE or ROPE-DRIVE to mounting plate. • Slide camlock nut at end of track into the groove, place and tighten it. Friction Drive Motor • Motor moves silently via drive wheel along the track. • Power via festoon cable. • Different speed and control options available. • Weight: depending on type 3.500 – 6.000 g. Drum Motor • Duty cycle: 40 %. • 3 x 230 / 400 VAC. • For rope up to Ø 3 mm. Limit Switch • With mounting plate and camlock nut for TRUMPF 95. Limit Switch Plate with Pulley • With mounting plate and camlock nut for TRUMPF 95. • For position “up” for guiding the returning rope. Operation Manual / TRUMPF 95 Limit switch and limit switch arm can be mounted to FRICTION-DRIVE motor, a master carrier or directly to the track. Limit switch and limit switch arm can be mounted to FRICTION-DRIVE motor, a master carrier or directly to the track.
2 System Installation 2.3.2 Rope Attachment 2.3.3 Rope Operation Test 2.3.4 Curtain Attachment 2.3.5 Curtain Operation Test After assembling all parts, the top cord operation cord can be attached. 1 Attach one end of the rope to a master runner. 2 Guide the other end of the rope through the rope guides over the head pulley to the floor pulley (or the motor) back up to the head pulley, to the return pulley and back to starting point. Attach it to the second master runner (if mounted). 3 Loosen the rope at the starting point (master runner), pull the rope tight and clamp it to the master runner. 4 After the installation, cut off the remaining ends of the rope to ensure a smooth operation. 5 Check the rope tension latest four weeks after installation. If necessary, adjust the tension. The different cord guide systems are shown in chapter 2.3 “Track Mounting”. Before attaching the curtain, the track system operation must be checked. Please pay attention to the following: Does the rope run smoothly, or does it rub against system components or other objects? If yes: change the rope alignment or add additional rope guides. Do you notice any unusual or loud operation noise? If yes: Find out the cause and replace defect parts where required. Do not exceed the maximum load capacity of the track system (see chapter 1.4) and its components. Attach the leading edge eyelet/grommet part of the curtain to the master runner’s attachment hole or the overlap arm. Attach the other end of the curtain to the end stop at the track end. There should be a distance of approx. 2 cm between the master runner attachment hole and the top edge of the curtain. This allows the runners to turn smoothly if stacking the curtain in the stacking area. The distance between the bottom edge of the curtain and the floor should be 1-3 cm to prevent the curtain from brushing over the floor. Attach decorative objects or scenery between 8 mm and 90 mm thickness via the scenery carrier bottom part (3100 0101) to the scenery carrier (3100 101) or with a M12 bolt directly to the scenery carrier. If using other attachment accessories to attach loads to the track system, verify that you do not exceed the load capacity and that all parts are in a proper condition. Check after curtain attachment: • Does the curtain move smoothly and easily? • Is there a danger of collision with other objects in the curtain area? If yes, enlarge the safety distance between curtain and other objects or remove the obstacles. • Repeat the test after removing the cause of the collision. Operation Manual / TRUMPF 95 31
Page 1 and 2: E Operation Manual Track System TRU
Page 3 and 4: 1 Introduction 1.1 General Instruct
Page 5 and 6: 2 System Installation 1.7 Safety In
Page 7 and 8: 2 System Installation 2.3.1 TRUMPF
Page 11 and 12: 2 System Installation 3115 1012 310
Page 25 and 26: 2 System Installation End view 3115
Page 29: 2 System Installation 2.3.1 TRUMPF
Page 33 and 34: 3 System Operation 3.1 Operator Ins
Page 35 and 36: Business hours Address Phone number

Operation manual Track System TRUMPF 95 - Gerriets

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?