Controls & Instrumentation Product Manual - Spirax Sarco

More documents

Recommendations

Info

Control Valves Globe Control Valves 144 Description The Spirax Sarco ‘C’ series valve range has a number of available options. The options relate to valve stem sealing, trim materials, valve flow characteristics and Cv capacity values. They are described in (and may be selected from) this TI. Valve characteristics See typical flow characteristic curves chart opposite The standard characteristic for the ‘C’ series valve is equal percentage (E), however the following options are available: Equal percentage E Linear L Fast opening F Modified equal percentage M Note: Modified special characteristic trims are designed upon request. Valve stem sealing PTFE chevron (P) Design temperature 14°F to 482°F (-10°C to +250°C) Material PTFE chevron Graphite (H) Design temperature 14°F to 572°F (-10°C to +300°C) standard bonnet 14°F to 1004°F (-10°C to +540°C) extended bonnet Bellows (B) Design temperature 14°F to 752°F (-10°C to +400°C) Material Carbon steel housing ASTM 216 WCB Pressure rating ANSI 150 Plug and seat treatment Hardened (T) Design temperature 14°F to 797°F (-10°C to +425°C) Material Stainless steel AISI 431 Leakage ANSI Class IV PTFE soft seat (G) Design temperature 14°F to 356°F (-10°C to +180°C) Material PTFE Leakage ANSI Class VI Hard face (W) Design temperature 14°F to 1004°F (-10°C to +540°C) Material Hard faced stellite AISI 316 Leakage ANSI Class IV or V Single and multiple stage cage Noise reducing perforated cage (P) Design temperature 14°F to 1004°F (-10°C to +540°C) Material Stainless steel AISI 316 ENC Anti-cavitation cage (A) Design temperature 14°F to 662°F (-10°C to +350°C) Material Stainless steel AISI 316 ENC ‘C’ Series Valve Options Typical valve flow characteristics ‘C’ series valve selection guide Local regulation may restrict the use of this product below the conditions quoted. Limiting conditions refer to standard connections only. In the interests of development and improvement of the product, we reserve the right to change the specification. 1", 1-1/2", 2", 2-1/2", 3", 4", 5", 6" & 8 Valve size DN25, 40, 50, 65, 80, 100, 125, 150 & 200 Valve series C = Cage trim L = Linear Valve E = Equal percentage characteristic F = Fast opening M = Modified equal percentage 4 = Carbon steel Body material 6 = Stainless Steel 8 = Alloy Steel 2 = Butt weld (2" to 8") Connections 3 = Flanged 4 = Socket weld (1", 1-1/2" and 2") Stem sealing options P = PTHE chevron H = Graphite B = Bellows T = AISI 431 hardened Seating options G = PTFE soft seat W = Hard face AISI 316 C = Standard cage Type of trim P = Noise reducing perforated cage A = Anti-cavitation cage 1 = One Number of 2 = Two stages 3 = Three Other = To be specified Trim balancing B = Balanced U = Unbalanced S = Standard Bonnet type H = Extended for high temperature L = Extended for low temperature 0 = No reduction Reduced trim 1 = 1 reduction 2 = 2 reductions 3 = 3 reductions Cv To be specified Connection type To be specified 2" C E 4 3 P T C 1 U S 1 C v 35 How to order Example: 1 of 2" CE43 PTC1US1 C v 35 flanged to ANSI 300. Flow % Fast opening Linear Equal percentage Valve opening % 2" C E 4 3 P T C 1 U S 1 C v 35 ANSI 300 ANSI 300 TI-F12-23-US 6.07
Valve capacities Flow coefficient C v (US) depending on the various trim options - K vs values are shown in brackets. Type of cage trim One stage standard One stage low noise Two stage low noise (Flow under) Three stage low noise (Flow under) One stage anti-cavitation (Flow over) Three stage anti-cavitation (Flow over) Flow characteristic Fast opening linear and Equal % Linear Modified Equal % Equal % Linear Modified Equal % Equal % Linear Modified Equal % Equal % Linear Linear Valve side Travel ‘C’ Series Valve Options 1" DN25 3/4" (20mm) 1-1/2" DN40 2" DN50 1-3/16" (30mm) Full area 19 (16) 35 (30) 63 (54) 95 (81) 130 (111) 216 (185) 293 (250) 386 (330) 560 (480) Reduction 1 19 (16) 35 (30) 63 (54) 95 (81) 130 (111) 216 (185) 293 (250) 386 (330) Reduction 2 19 (16) 35 (30) 63 (54) 95 (81) 130 (111) 216 (185) 293 (250) Reduction 3 19 (16) 35 (30) 63 (54) 95 (81) 130 (111) 216 (185) Maximum 15 (13) 35 (30) 60 (51) 100 (86) 140 (120) 250 (214) 320 (274) 425 (364) 650 (556) Reduction 1 15 (13) 35 (30) 60 (51) 100 (86) 140 (120) 250 (214) 320 (274) 425 (364) Reduction 2 15 (13) 35 (30) 60 (51) 100 (86) 140 (120) 250 (214) 320 (274) Reduction 3 15 (13) 35 (30) 60 (51) 100 (86) 140 (120) 250 (214) Maximum 15 (13) 30 (26) 55 (47) 85 (73) 120 (103) 200 (171) 250 (214) 360 (308) 530 (453) Reduction 1 15 (13) 30 (26) 55 (47) 85 (73) 120 (103) 200 (171) 250 (214) 360 (308) Reduction 2 15 (13) 30 (26) 55 (47) 85 (73) 120 (103) 200 (171) 250 (214) Reduction 3 15 (13) 30 (26) 55 (47) 85 (73) 120 (103) 200 (171) Maximum 15 (13) 25 (21) 45 (39) 75 (64) 95 (81) 150 (128) 210 (178) 280 (240) 425 (364) Reduction 1 15 (13) 25 (21) 45 (39) 75 (64) 95 (81) 150 (128) 210 (178) 280 (240) Reduction 2 15 (13) 25 (21) 45 (39) 75 (64) 95 (81) 150 (128) 210 (178) Reduction 3 15 (13) 25 (21) 45 (39) 75 (64) 95 (81) 150 (128) Maximum 17 (14.5) 28 (24) 46 (39) 70 (60) 125 (107) 170 (145) 250 (214) 440 (376) Reduction 1 17 (14.5) 28 (24) 46 (39) 70 (60) 125 (107) 170 (145) 250 (214) Reduction 2 17 (14.5) 28 (24) 46 (39) 70 (60) 125 (107) 170 (145) Reduction 3 17 (14.5) 28 (24) 46 (39) 70 (60) 125 (107) Maximum 15 (13) 26 (22) 43 (37) 65 (56) 115 (98) 155 (133) 230 (197) 400 (342) Reduction 1 15 (13) 26 (22) 43 (37) 65 (56) 115 (98) 155 (133) 230 (197) Reduction 2 15 (13) 26 (22) 43 (37) 65 (56) 115 (98) 155 (133) Reduction 3 15 (13) 26 (22) 43 (37) 65 (56) 115 (98) Maximum 13 (11) 22 (19) 40 (34) 60 (52) 110 (94) 145 (125) 210 (180) 370 (317) Reduction 1 13 (11) 22 (19) 40 (34) 60 (52) 110 (94) 145 (125) 210 (180) Reduction 2 13 (11) 22 (19) 40 (34) 60 (52) 110 (94) 145 (125) Reduction 3 13 (11) 22 (19) 40 (34) 60 (52) 110 (94) Maximum 13 (11) 20 (17) 35 (30) 50 (43) 85 (73) 105 (90) 155 (133) 280 (240) Reduction 1 13 (11) 20 (17) 35 (30) 50 (43) 85 (73) 105 (90) 155 (133) Reduction 2 13 (11) 20 (17) 35 (30) 50 (43) 85 (73) 105 (90) Reduction 3 13 (11) 20 (17) 35 (30) 50 (43) 85 (73) Maximum 10 (8.5) 15 (13) 30 (26) 45 (39) 75 (64) 95 (81) 145 (124) 250 (214) Reduction 1 10 (8.5) 15 (13) 30 (26) 45 (39) 75 (64) 95 (81) 145 (124) Reduction 2 10 (8.5) 15 (13) 30 (26) 45 (39) 75 (64) 95 (81) Reduction 3 10 (8.5) 15 (13) 30 (26) 45 (39) 75 (64) Maximum 7 (6) 10 (8.5) 25 (21.5) 30 (26) 55 (47) 75 (64) 115 (99) 200 (171) Reduction 1 7 (6) 10 (8.5) 25 (21.5) 30 (26) 55 (47) 75 (64) 115 (99) Reduction 2 7 (6) 10 (8.5) 25 (21.5) 30 (26) 55 (47) 75 (64) Reduction 3 7 (6) 10 (8.5) 25 (21.5) 30 (26) 55 (47) Maximum 15 (13) 30 (26) 55 (47) 85 (73) 120 (103) 200 (171) 250 (214) 360 (308) 530 (453) Reduction 1 15 (13) 30 (26) 55 (47) 85 (73) 120 (103) 200 (171) 250 (214) 360 (308) Reduction 2 15 (13) 30 (26) 55 (47) 85 (73) 120 (103) 200 (171) 250 (214) Reduction 3 15 (13) 30 (26) 55 (47) 85 (73) 120 (103) 200 (171) Maximum 15 (13) 26 (22) 43 (37) 65 (56) 115 (98) 155 (133) 230 (197) 400 (342) Reduction 1 15 (13) 26 (22) 43 (37) 65 (56) 115 (98) 155 (133) 230 (197) Reduction 2 15 (13) 26 (22) 43 (37) 65 (56) 115 (98) 155 (133) Reduction 3 15 (13) 26 (22) 43 (37) 65 (56) 115 (98) For conversion Cv (UK) = Cv (US) x 0.833 Kvs = Cv (US) x 0.855 Cv (Kvs) by valve size and trim reduction 2-1/2" DN65 1-1/2" (38mm) 3" DN80 4" DN100 2" (50mm) Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222 5" DN125 2-1/2" (65mm) 6" DN150 8" DN200 3" (75mm) TI-F12-23-US 6.07 Control Valves Globe Control Valves 145
Page 1:
spiraxsarco.com/us Controls & Instr
Page 4 and 5:
2 Copyright © 2011 by Spirax Sarco
Page 6 and 7:
4 How To Use This Book Accepted int
Page 9 and 10:
CONTROLS & INSTRUMENTATION Product
Page 11 and 12:
Boiler Controls Index Tech. Illus.
Page 13 and 14:
Safety information WARNING Your att
Page 15 and 16:
Dimensions (approximate) in inches
Page 17 and 18:
LC1350 Level Controller Description
Page 19 and 20:
LC1350 OK AL LC1350 Level Controlle
Page 21 and 22:
LC2250 Level Controller Technical d
Page 23 and 24:
Spirax Sarco, Inc., 1150 Northpoint
Page 25 and 26:
Page 27 and 28:
LC2650 Level Controller Safety info
Page 29 and 30:
Page 31 and 32:
• Loop powered 4-20mA input • P
Page 33 and 34:
Page 35 and 36:
LP 31 High Level Alarm Probe Dimens
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Limiting conditions Maximum boiler
Page 43 and 44:
S20 Sensor Chamber, TP20 Temperatur
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
BC3150 Blowdown Controller Technica
Page 51 and 52:
BC3150 Blowdown Controller Safety i
Page 53 and 54:
BC3250 Blowdown Controller Technica
Page 55 and 56:
BC3250 Blowdown Controller Safety i
Page 57 and 58:
Dimensions/weight (approximate) in
Page 59 and 60:
3/4" BCV 30 Blowdown Control Valve
Page 61 and 62:
1-1/2" BCV 30 Blowdown Control Valv
Page 63 and 64:
Dimensions/weight (approximate) in
Page 65 and 66:
1-1/2" BCV 31 Blowdown Control Valv
Page 67 and 68:
• Automatic temperature compensat
Page 69 and 70:
Page 71 and 72:
Dimensions/weights Weight (approxim
Page 73 and 74:
KBV 20 Key Operated Boiler Blowdown
Page 75 and 76:
ABV 20 Air Actuated Boiler Blowdown
Page 77 and 78:
Control Valves Index Tech. Illus. M
Page 79 and 80:
Control Valves Index (continued) Te
Page 81 and 82:
Page 83 and 84:
PM Series Pneumatic Actuators for B
Page 85 and 86:
B Series 1/2" to 2" 2-Way and 3-Way
Page 87 and 88:
SPIRA-TROL 1/2" to 4" ANSI Two-port
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96: SPIRA-TROL 1/2" to 4" ANSI Two-port
Page 107 and 108: SPIRA-TROL 6" and 8" KEA, KFA and K
Page 115 and 116: STERI-TROL Clean Service 'S' series
Page 117 and 118: PN 9000 series actuators No. Part M
Page 119 and 120: Pressure / temperature limits 338 3
Page 121 and 122: Maximum differential pressures for
Page 127 and 128: Actuator and SA valve C E B1 A SH v
Page 129 and 130: How to order Ordering a control val
Page 131 and 132: Available spares for the PN9000 ser
Page 133 and 134: 7 CE43 1" (DN25) to 4" (DN100) Carb
Page 135 and 136: CE43 5" (DN125) to 8" (DN200) Carbo
Page 137 and 138: CE83 1" (DN25) to 4" (DN100) Alloy
Page 139 and 140: CE83 5" (DN125) to 8" (DN200) Alloy
Page 141 and 142: CE63 1" (DN25) to 4" (DN100) Stainl
Page 143 and 144: CE63 5" (DN125) to 8" (DN200) Stain
Page 145: Spare parts The spare parts availab
Page 149 and 150: Materials TN2000 Series Pneumatic P
Page 151 and 152: TN2000 Series Pneumatic Piston Actu
Page 153 and 154: TN2000 series selection guide: Spar
Page 155 and 156: Materials 2 5 28 22 and 23 3 4 7 31
Page 157 and 158: PN9000 Series Pneumatic Actuators f
Page 163 and 164: PN1000 Series Spring Extend Pneumat
Page 165 and 166: PN1000 Series Spring Extend Pneumat
Page 167 and 168: Spirax Sarco, Inc., 1150 Northpoint
Page 169 and 170: Materials - PN1300 to PN1600 No. Pa
Page 171 and 172: ‘C’ series valve Valve size Sta
Page 173 and 174: Dimensions / weights (approximately
Page 177 and 178: Installation and Wiring The valves
Page 179 and 180: Installation and Wiring The valves
Page 181 and 182: Approvals This equipment is CE mark
Page 185 and 186: Actuator EL5650 Series Electric Act
Page 189 and 190: Accessories for EL5600 Series Actua
Page 191 and 192: Rotork CVL Electric Actuators For S
Page 195 and 196: Installation Full details are conta
Page 197 and 198:
EP5 Electro Pneumatic Positioner IS
Page 199 and 200:
SP400 Electropneumatic Smart Positi
Page 201 and 202:
Programmable functions Autostroke A
Page 203 and 204:
Models & Protocols The communicatio
Page 205 and 206:
SP30 Positioner with digital displa
Page 207 and 208:
Description The IPC4A Convertor is
Page 209 and 210:
MPC2 High Efficiency Compressed Air
Page 211 and 212:
Description The Stonel Limit Switch
Page 213 and 214:
PN600 Series Pneumatic Controllers
Page 215 and 216:
SX27 general technical data Mountin
Page 217 and 218:
SX77+ technical data Mounting arran
Page 219 and 220:
Mechanical data EL2270* EL2271 Prod
Page 221 and 222:
EL2600 Low pressure 'U' syphon High
Page 223 and 224:
PF6 Series Stainless Steel Piston A
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Pressure / temperature limits Body
Page 233 and 234:
PF51G Bronze Piston Actuated On/Off
Page 235 and 236:
PF51G Bronze Piston Actuated On/Off
Page 237 and 238:
Associated equipment PF51G Bronze P
Page 239 and 240:
Mounting Banjo connection Manual ov
Page 241 and 242:
M D M 9 2 N - 4 MDM 4 Banked Pilot
Page 243 and 244:
M10Si ISO Automation Ball Valve 1/4
Page 245 and 246:
Page 247 and 248:
Materials 13 12 20 17 11 4 9, 19 17
Page 249 and 250:
Description The M10Ti ISO three-pie
Page 251 and 252:
Dimensions (approximate) in Inches
Page 253 and 254:
Materials 13 12 20 1 11 4 9, 19 17
Page 255 and 256:
Description The M10Pi ISO three-pie
Page 257 and 258:
Dimensions (approximate) in Inches
Page 259 and 260:
Materials No. Part Material 1 Body
Page 261 and 262:
Page 263 and 264:
Temperature °C Pressure psig 0 200
Page 265 and 266:
M70i ISO Forged Stainless Steel Bal
Page 267 and 268:
M80i ISO Stainless Steel Ball Valve
Page 269 and 270:
M80i ISO Stainless Steel Ball Valve
Page 271 and 272:
2"(DN50) shown for the main illustr
Page 273 and 274:
Spare parts The spare parts availab
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
1" to 2" Materials No. Part Materia
Page 285 and 286:
Dimensions/weights (approximate) in
Page 287 and 288:
2½" to 6" - Spare parts The spare
Page 289 and 290:
Compressed air consumption Nm3 /str
Page 291 and 292:
M10HPi ISO ball valves Actuator ope
Page 293 and 294:
M70i ISO ball valve Actuator operat
Page 295 and 296:
M20S ball valve Actuator operating
Page 297 and 298:
Description The SENTINEL VPT has be
Page 299 and 300:
Page 301 and 302:
Gauge Temper- Heat in Btu/lb Specif
Page 303 and 304:
Warm-up and Condensate Load Tables
Page 305 and 306:
Designing of Steam Tracing Recommen
Page 307 and 308:
Condensate return lines on the disc
Page 309 and 310:
As the USA’s leading provider of
Page 311 and 312:
NOTES 309
Page 313 and 314:
NOTES 311
Page 316:
spiraxsarco.com/us SPIRAX SARCO, IN
show all

Controls & Instrumentation Product Manual - Spirax Sarco

Create successful ePaper yourself

Delete template?

Save as template?