SmartFade ML v3.0.1 Release Note - ETC
SmartFade ML v3.0.1 Release Note - ETC
SmartFade ML v3.0.1 Release Note - ETC
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>ETC</strong> <strong>Release</strong> <strong>Note</strong>:<br />
Key Enhancements in v3.0.0<br />
<strong>SmartFade</strong> <strong>ML</strong> <strong>v3.0.1</strong> Software<br />
SF<strong>ML</strong> Important Change for Device Personalities:<br />
The console contains about 500 standard devices (about 40% of the previous number). A separate<br />
file called PERSLIB.BIN may be placed on an SD card and browsed on the console, or in the<br />
simulator in SmartSoft, and this contains over 3000 more personalities, more than double than in<br />
previous versions. In future new personalities will be distributed in this file allowing <strong>SmartFade</strong> <strong>ML</strong><br />
to support an unlimited number of devices. You may load from the file into the console up to 100<br />
personalities. You may also make your own personalities as before.<br />
Additional Enhancements:<br />
• Stack cues may now be recorded in any numerical order and they will play back in correct<br />
numerical sequence. Cues may be numbered from 1 to 199 and point cues may be<br />
inserted anywhere from 0.1 to 199.9. The total number of cues remains fixed at 199.<br />
• Stack editing has been simplified. Now there is one type of edit for any step number.<br />
• The consoles are now set to default on to General MIDI and interconnect immediately.<br />
• Color control for many device types are now supported: RGB, CMY, RGBA, RAGCB<br />
(Prism Reveal), ROAGI (Selador Fire), RGCBI, (Selador Ice), ROAGCBI (Selador x7).<br />
• User personalities may be made with RGB, RGBA or CMY mixing<br />
• It is now possible to turn off rubberbanding on memory faders. When on, moving light<br />
parameters (non intensity channels) will follow the fader back and forth. When off, the<br />
parameters will move to their new positions as you take up a fader and then remain there<br />
when the fader is taken down.<br />
Key Enhancements in v2.1.2<br />
• Bug fixes.<br />
Software Installation<br />
<strong>Note</strong>:<br />
If you received your console after February 20, 2008, deep clearing the console<br />
may cause it to lose an LED color calibration for the “white” color in the device<br />
selects (seen when devices are patched and selected). It is simple to recalibrate<br />
these LEDs back to an acceptable white color using the console's SETTINGS<br />
menu. If you need to deep clear or load new software into your console and this<br />
calibration needs to be made, use the MENU key to enter the console<br />
menus, scroll to SETTINGS and press , then scroll to LED CALIBRATION<br />
and press . Use the dials to adjust the red, green and blue settings to an<br />
acceptable “white” color (this typically means leaving red at 255 and adjusting<br />
green and blue to a level up and/or down from the default level of 217 until a warm<br />
white color is achieved).<br />
When you have calibrated the LEDs you may save these settings in a file on an<br />
SD card for future recall if required after a software upgrade or system deep-clear.<br />
In the calibration menu scroll to save calibration. The calibration may only be<br />
saved to an SD card in the console.<br />
These are the instructions for updating the software in your <strong>SmartFade</strong> <strong>ML</strong> console. There are two<br />
ways of updating the software.<br />
• Using a standard SD card (not an SDHC card)<br />
• Connecting with USB to a PC<br />
Software can be downloaded from the <strong>ETC</strong> Web site: www.etcconnect.com<br />
<strong>SmartFade</strong> <strong>ML</strong> <strong>v3.0.1</strong> <strong>Release</strong> <strong>Note</strong> Page 2 of 4 Electronic Theatre Controls, Inc.