Tesis previa a la obtención del Título de Ingeniero en Electrónica y ...
Tesis previa a la obtención del Título de Ingeniero en Electrónica y ...
Tesis previa a la obtención del Título de Ingeniero en Electrónica y ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
3.4 C&I re<strong>la</strong>ted to simple multipoint confer<strong>en</strong>ces not using MLP<br />
Note — Some of the following co<strong>de</strong>s may be cancelled by transmission of appropríate co<strong>de</strong>s as listed in<br />
Table 1/H.230 but not separately <strong>de</strong>fined here.<br />
MCV Multipoint Command Visualization-Forcing: transmitted by a terminal to forcé an associated MCU<br />
to broadcast its vi<strong>de</strong>o signal. (Used to transmit the picture of a chairman or VIP, alternatively to<br />
hold a picture source during the transmission of graphics.)<br />
MIV Multipoint Indication Visualizaron: transmitted by an MCU to indícate to a terminal that its<br />
vi<strong>de</strong>o signal is being se<strong>en</strong> by other termináis (otherwise known as "On-air" indication).<br />
MCC Multipoint Command Confer<strong>en</strong>ce: transmitted by an MCU to a terminal. The terminal receiving<br />
MCC must make its outgoing transfer rate equal to its incoming transfer rate, and its outgoing<br />
audio rate equal to its incoming audio rate.<br />
Note — The command could also be used to invoke an on-scre<strong>en</strong> user indication.<br />
MCS Multipoint Command Symmetrical Data-transmission: transmitted by an MCU wh<strong>en</strong> setting up<br />
data broadcasting. On receipt, a terminal must prepare itself for data reception and <strong>en</strong>sure, by<br />
mo<strong>de</strong> change if necessary, that its outgoing data channel occupies the same capacity as its incoming<br />
data channel. A terminal in receipt of MCS cannot initiate data broadcasting.<br />
MCN Multipoint Command Negating MCS: transmitted by an MCU at the completion of data<br />
broadcasting. On receipt, a terminal must cióse any outgoing data channel which it has op<strong>en</strong>ed as a<br />
result of the previous reception of MCS. Following the <strong>en</strong>d of data reception and the receipt of<br />
MCN, a terminal is permitted to initiate data broadcasting.<br />
MIL Multipoint Indication Loop: an MCU has had iís ports extemally looped. The topic is for further<br />
study.<br />
MIZ Multipoint Indication Zero-communication: transmitted by an MCU to a terminal for information,<br />
with the meaning that no other termináis are yet connected to the MCU.<br />
MIS Multipoint Indication Secondary-status: transmitted by an MCU to a terminal for information, with<br />
the meaning that since other termináis of higher capability are participating in the confer<strong>en</strong>ce-call,<br />
this terminal will not necessarily receive all the signáis that are s<strong>en</strong>t to those other termináis (see<br />
Recomm<strong>en</strong>dation H.200/AV.243).<br />
MCA Multipoint Command Assign-tok<strong>en</strong>: possession of the tok<strong>en</strong> gives the holding terminal the right to<br />
give the MCU certain cornmands (see Recomm<strong>en</strong>dation H.200/AV.243).<br />
MCT Multipoint Command Tok<strong>en</strong>-c<strong>la</strong>im: s<strong>en</strong>t by a terminal to the MCU. The MCU acce<strong>de</strong>s to this<br />
c<strong>la</strong>im if the tok<strong>en</strong> is unassigned or has be<strong>en</strong> released.<br />
MCR Multipoint Command Reléase-tok<strong>en</strong>: s<strong>en</strong>t to the MCU by the terminal holding the tok<strong>en</strong> to give the<br />
MCU the authority to reassign the tok<strong>en</strong> to another terminal wh<strong>en</strong>/if it receives MCT.