Manual de Hardware - Panasonic Electric Works
Manual de Hardware - Panasonic Electric Works
Manual de Hardware - Panasonic Electric Works
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Mantenimiento<br />
FP2<br />
7.2 Mantenimiento Preventivo<br />
7.2 Mantenimiento Preventivo<br />
Aunque el FP2 ha sido diseñado para minimizar el mantenimiento, se ha <strong>de</strong> tener en<br />
consi<strong>de</strong>ración algunos aspectos <strong>de</strong> mantenimiento.<br />
Si periódicamente se realiza un mantenimiento a<strong>de</strong>cuado se asegura el correcto<br />
funcionamiento <strong>de</strong>l sistema.<br />
Elemento Descripción Acción Referencias<br />
Fuente <strong>de</strong><br />
Chequear el led <strong>de</strong> la fuente <strong>de</strong> Normal si está a ON Sección 2.4<br />
Alimentación<br />
alientación [POWER LED]<br />
Fuente <strong>de</strong> Alimentación Recambio periódico a las 20,000<br />
horas <strong>de</strong> trabajo<br />
Leds <strong>de</strong> la CPU Chequear el led <strong>de</strong> RUN ON en modo RUN Sección 2.3 y 6.1<br />
Chequear el led <strong>de</strong> ERROR Normal si está a OFF<br />
Chequear el led <strong>de</strong> ALARM Normal si está a OFF<br />
Chequear el led <strong>de</strong> BATT. Normal si está a OFF<br />
Leds <strong>de</strong> los Módulos<br />
<strong>de</strong> Entradas y Salidas<br />
Condiciones <strong>de</strong> la<br />
Instalación<br />
Condiciones <strong>de</strong> la<br />
Conexión<br />
Chequear el led <strong>de</strong> estado <strong>de</strong> las<br />
Entradas y Salidas<br />
Normal si está encendido cuando<br />
ON, y apagado cuando OFF<br />
j<br />
Sección 2.5<br />
Aflojamiento <strong>de</strong>l montaje <strong>de</strong>l rack<br />
Aflojamiento <strong>de</strong>l módulo<br />
Monaje correctamente anclado Sección 4.1.1 y<br />
4.1.2<br />
Aflojamiento <strong>de</strong>l terminal al tornillo Anclaje correcto Sección 4.1.3,<br />
Contacto entre los pines <strong>de</strong>l En dos columnas paralelas.<br />
4.2, 4.4 y 4.5<br />
terminal<br />
Aflojamiento <strong>de</strong>l conector<br />
Conector y terminal anclados<br />
Conexión <strong>de</strong>l cable <strong>de</strong> expansión Cable y racks anclados<br />
Voltaje<strong>de</strong>laFuente Voltaje entre terminales<br />
FP2 -PSA1:<br />
Sección 4.2.1<br />
<strong>de</strong> Alimentación<br />
100 a 120V AC<br />
FP2 -PSA2:<br />
200 a 240V AC<br />
FP2 -PSA3:<br />
100 a 240V AC<br />
Alimentación <strong>de</strong> las<br />
Entradas y Salidas<br />
Voltaje entre terminales<br />
En el rango especificado para<br />
cada módulo<br />
Sección 2.6, 2.7<br />
y 2.8<br />
Temperatura <strong>de</strong>l Temperatura Ambiente 0a55⎪C Sección 4.1.1<br />
Entorno<br />
Humedad Ambiente 30 a 85%<br />
Condiciones <strong>de</strong> Operación Sin polvo ni gas corrosivo<br />
B at erí a d e B acku p Batería<strong>de</strong>laCPU Reemplazar periodicamente Sección 7.1.1<br />
7-- 6 Matsushita <strong>Electric</strong> <strong>Works</strong> (Europe) AG