GALILEO/CEILING FAN GALILEO/VENTILADOR DE TECHO - Lowe's

More documents

Recommendations

Info

$LATEX GRAVITY FEED HVLP SPRAY GUN$

DIM ON/OFFAUTOMATED LEARNING PROCESS/ACTIVATING CO<strong>DE</strong>CAUTION: The remote control transmitter (P) can be programmedto multiple receivers or fans. If this is not desired, turn wall switchoff to any other programmable receiver or fan.1. Locate the two batteries (O) and then remove plastic that iswrapped around batteries (O). Remove battery cover from backside of transmitter (P). Install the two 1.5-volt (AA) batteries (O)provided--(refer to drawing at right).PO2. Locate dimmer switch in the top left part of the batterycompartment labeled “DIM”. (refer to drawing at right) Set dimmerswitch to the “ON” position. [Note: If you prefer not to havedimming capability, set dimmer switch to “OFF” position.]3. Restore electrical power. Within 60 seconds of restoringelectrical power, press the “LEARN” button in the batterycompartment (refer to drawing at right) for 5 seconds or until fanswitches to MEDIUM speed. Test the light and fan functions toconfirm the learning process is complete.4. Replace battery cover on transmitter (P)--refer to drawing atright.IMPORTANT: To prevent damage to remote control transmitter(P), remove the batteries (O) if not used for long periods. Store thetransmitter (P) away from excess heat or humidity.LEARNDIM ON/OFFLEARNBatteryCoverBULB REPLACEMENT FOR UP-LIGHTIMPORTANT: The motor housing (E), as well as thebulbs (G) themselves, can become extremely hot whenthe light has been on; therefore, please allow sufficienttime for motor housing (E) and bulbs (G) to cool downbefore touching.Replace burnt-out bulb (G) with one candelabra base15-watt max. bulb. Repeat for each burnt-out bulb (G).GECARE AND MAINTENANCEAt least twice each year, lower canopy (B) to check downrod (A) assembly, and then tighten all screws on the fan.Clean motor housing (E) with only a soft brush or lint-free cloth to avoid scratching the finish. Clean blades (H)with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for addedprotection.IMPORTANT: Shut off main power supply before beginning any maintenance. Do not use water or a damp clothto clean the ceiling fan.10
TROUBLESHOOTINGWarning: Before beginning work, shut off the power supply to avoid electrical shock.Problem Possible Cause Corrective ActionFan does not move. 1. Power is off or fuse is blown. 1. Turn power on or check fuse.2. Faulty wire connection. 2. Turn power off. Loosen canopy(B) and check all connections.3. Plugs and/or antenna wire not 3. Check that male and female plugsconnected properly.and/or antenna wire in switch housing areconnected properly according toinstructions on page 8.Noisy operation. 1. Blades (H) are loose. 1. Tighten all blade screws (I).2. Cracked blade (H). 2. Replace blade (H).3. Full range dimmer switch. 3. Replace with ON/OFF wall switch only.4. Fan is new. 4. Allow fan a “break in” period of afew days, especially when runningthe fan at Medium and High speeds.Excessive wobbling. 1. Blades (H) are loose. 1. Tighten all blade screws (I).2. Unbalanced blades (H). 2. Switch one blade (H) with ablade (H) from the opposite side.3. Fan not securely mounted. 3. Turn power off. Carefully loosencanopy (B) and verify that mountingbracket (C) is secure.4. Fan too close to vaulted ceiling. 4. Use a longer downrod (A) or move fanto another location.5. Set screw(s) on motor housing 5. Tighten yoke set screw(s) securely.yoke is (are) not tightened properly.6. Set screw on hanging ball is not 6. Carefully loosen and lower screw ontightened properly.canopy (B) and verify that set screw onhanging ball is tightened securely.Fan operates but lights 1. Bulb(s) not installed correctly. 1. Re-install bulb(s).fail (if applicable). 2. Wires in canopy (B) not wired 2. Check wires in canopy (B) and, ifproperly.necessary, re-wire according toinstructions on page 6 and 7.3. Wall switch to fan is off. 3. Make sure that wall switch to fan is on.4. Plugs and/or antenna wire not 4. Check that male and female plugsconnected properly.and/or antenna wire in switch housing areconnected properly according toinstructions on page 8.5. Light kit is lamped with more 5. Lamp light kit with bulbs that total nothan the allowable 190W, causing more than 190W.the wattage limiting device tointerrupt the flow of electricity to the lightkit.Note: A small amount of “wobble” is normal and should not be considered a defect.11
Page 1 and 2: SOS ITEM/ARTICULO SOS #0131430GALIL
Page 3 and 4: SAFETY INFORMATIONREAD AND SAVE THE
Page 5 and 6: PREPARATION1. Before beginning asse
Page 7 and 8: WIRING1. [NOTE: For each wire conne
Page 9: FINAL INSTALLATION5. Install three
Page 13 and 14: ARTICULO SOS #0131430GALILEO/VENTIL
Page 15 and 16: INFORMACION DE SEGURIDADPOR FAVOR L
Page 17 and 18: PREPARACION1. Antes de empezar con
Page 19 and 20: CONEXION DE LOS CABLES1. [NOTA: Par
Page 21 and 22: INSTALACION FINAL5. Instale las tre
Page 23 and 24: LOCALIZACION DE FALLASADVERTENCIA:

GALILEO/CEILING FAN GALILEO/VENTILADOR DE TECHO - Lowe's

Create successful ePaper yourself

Delete template?

Save as template?