GALILEO/CEILING FAN GALILEO/VENTILADOR DE TECHO - Lowe's

More documents

Recommendations

Info

$LATEX GRAVITY FEED HVLP SPRAY GUN$

FINAL INSTALLATION2. Locate the motor housing screws pre-installed in the top of themotor housing (E) and remove screws with a Phillips screwdriver.Align holes in scroll iron (D) with screw holes in top of motorhousing (E). Re-install motor housing screws that were previouslyremoved and securely tighten screws. (Fig. 2)Repeat procedure for remaining scroll irons (D).DMotorHousingScrews<strong>DE</strong>Fig. 23. Remove cardboard pieces from between fitter plate and bladeband.TIP: Use of a magnetic tip screwdriver is recommended.Locate 12 blade screws (I) and blade washers (J) in hardwarepack. Blade washers (J) for blade screws (I) can be set on eachblade screw (I) prior to installing blades (H).Slide blade (H) through one of the narrow, rectangular openings onblade band, aligning holes in blade (H) with holes located insidemotor housing (E). [Note: Turn blade band in order to align/insertblade screws (I) and blade washers (J).] Insert three blade screws(I), along with blade washers (J), and then tighten blade screws (I)securely with a Phillips screwdriver. (Fig. 3) Repeat procedure foreach remaining blade (H).BladeBandFig. 3JIEHFitter Plate4. Remove three screws from fitter plate on underside of motorhousing (E). (Fig. 4)Connect female plug in the receiver to male plug from motorhousing (E). Make sure plugs connect tightly. Connectantenna wire that extends from fitter plate to antenna wire fromreceiver. Make sure molex connections on these two wiresconnects tightly. (Fig. 4)Fitter PlateEAntenna WireMale PlugFemale PlugAlign holes in light kit fitter (F) with holes in fitter plate.Re-install three screws that were previously removed. Tightenscrews securely with a Phillips screwdriver. (Fig. 4)ReceiverFig. 4F8
FINAL INSTALLATION5. Install three 50-watt max. halogen bulbs (R) included. (Fig. 5)IMPORTANT: When replacing bulbs, allow bulbs and light kit tocool before touching them.FRFig. 5REMOTE CONTROL OPERATIONOperation buttons on the panel of the transmitter (P):HI buttonMED buttonLOW buttonOFF buttonUP buttonDOWN buttonREV buttonfor fan HIGH speedfor fan MEDIUM speedfor fan LOW speedfor turning fan OFFfor light ON/OFF, upper lightfor light BRIGHTNESS and OFF, lower lightto REVERSE blade direction (fan must be onlow before reversing blade direction)PThe light function is controlled by pressing the UP and/or DOWN button.Tap either UP or DOWN button quickly to turn lights off or on. HoldDOWN button down to increase or decrease lights. If you press DOWNbutton in excess of 0.7 seconds it becomes a dimmer. The lights varycyclically in 0.8 seconds. The DOWN light button has an auto resumefunction which keeps the lights at the same brightness as the last timethey were turned off.9
Page 1 and 2: SOS ITEM/ARTICULO SOS #0131430GALIL
Page 3 and 4: SAFETY INFORMATIONREAD AND SAVE THE
Page 5 and 6: PREPARATION1. Before beginning asse
Page 7: WIRING1. [NOTE: For each wire conne
Page 11 and 12: TROUBLESHOOTINGWarning: Before begi
Page 13 and 14: ARTICULO SOS #0131430GALILEO/VENTIL
Page 15 and 16: INFORMACION DE SEGURIDADPOR FAVOR L
Page 17 and 18: PREPARACION1. Antes de empezar con
Page 19 and 20: CONEXION DE LOS CABLES1. [NOTA: Par
Page 21 and 22: INSTALACION FINAL5. Instale las tre
Page 23 and 24: LOCALIZACION DE FALLASADVERTENCIA:

GALILEO/CEILING FAN GALILEO/VENTILADOR DE TECHO - Lowe's

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?