1 - ProIdea

8g DRAININGThe SANICUBIC ® Classic unit is fitted with 2 plugs ( 8g 1 ).Disconnect the unit from the power supply.To drain the unit1- Unclip the cover.2- Remove one of the 2 plugs.3- Insert a wet utility vacuum cleaner pipe to drain the unit. Theport diameter is 40 mm.4- When the unit has been drained, putthe plug and then the cover back in place.8h FIXING THE SANICUBIC UNIT TO THE FLOORThe SANICUBIC ® Classic unit is equipped with fittings to hold iton the floor andprevent it from turning or moving.1- Place the unit on the desired spot.2- Draw the outline of the unit.3- Position the brackets and fix them to the floor as shown on thetemplate diagram ( 8h 1 ).4- Put the unit back in place.5- Fix the unit in place with the screws.8i ELECTRICAL CONNECTIONS1- The electrical installation work must be carried out by aqualified electrician.The electrical installation must comply with the standards inforce in the country concerned2- The power supply must be of the class 1 type. The unit must beconnected via an earthed connection box. The electric powercircuit must be protected by a high-sensitivity 30 mA differentialcircuit breaker set at 20 A. The connection must be used solelyto power the SANICUBIC ® Classic. If the power lead on the unitis damaged, it must be replaced by the manufacturer or itsafter-sales service to avoid all danger.9ALARM OPERATION1/ General alarms:High level alarm:If the water level in the unit is abnormally high: the buzzer istriggered and the red LED comes on; the other motor starts up3 seconds later (see the illustration showing the controlkeyboard).Temporary alarm:If one of the 2 motors runs for more than 1 minute: the buzzer istriggered and the red alarm LED comes on; the other motor startsup 3 seconds later.2/ Resetting the general alarms:If the problem that has triggered one of the alarms referred toabove ceases, the buzzer stops, but the red alarm LED stayson to memorize the fact that the system has met with aproblem.The “Reset alarm” key on the keyboard is used to switch thebuzzer off in all cases, but it only switches the red LED off ifthe problem that triggered the alarm has been dealt with. Thisavoids the risk of having a system “abandoned” in fault status.10CONFORMITY WITH STANDARDS• SANICUBIC ® Classic complies with standard EN 12050-1 (liftstation for household waste containing faeces) and with theEuropean directives covering construction products, electricalsafety and electromagnetic compatibilityThis unit must be installed and used in compliance withEuropean installation standard EN12056 and with localrequirements.11COMMISSIONING1- Once the plumbing and electrical connections have beenmade, check that the connections are watertight byletting water flow successively through each inlet used.Make sure that the unit is operating correctly by carryingout at least two start cycles with water to test the system.2 - WARNING! Do not operate the motors in overridestatus (by pressing the pushbuttonson the control box) until the pumps have been filledwith water. Operation without water damages themaceration system.12USE1- The SANICUBIC ® Classic unit is designed to drain offhousehold waste water. Any other use will invalidate theguarantee. Do not dispose of sanitary towels, condoms,hygiene articles, oils, solvents, acids, or any other potentiallycorrosive or explosive liquids etc., via the unit.2- WARNING: In the event of a power failure, stopdraining any water from the equipment connectedto the SANICUBIC ® Classic unit.3- Do not install or use the unit in a zone where there is arisk of explosion.13 MAINTENANCEA visual check of the lift station must be made once a monthto make sure it is operating correctly, and the installationmust be inspected regularly (once a year) by a qualifiedperson. Meanwhile if encounter technical problems, pleaseask our after-sales service for advice. If the power supplycable of the unit is damaged, it must be replaced by themanufacturer or its after-sales service to avoid all danger.14GUARANTEEThe SANICUBIC ® Classic unit is guaranteed for two years(parts and labour) provided that it has been installed andused in compliance with the present instructions.UNIT ALARMmotor 1LEDmotor 2LED“Alarm”LED“Mains”LEDmotor 1“Override”motor 2“Override”“RESET”Alarm