Rheotest english

More documents

Recommendations

Info

• The basic plate with automatic distance adjustment consists of moveable parts. For avoiding injuries,please apply samples only during standstill of the device.Attention!The instrument should not be put into service in case of considerable external damages or heavynoise during operation.3 Scope of Supply3.1 Scope of Supply for Rheometer RHEOTEST ® RNThe measuring instrument Rheometer RHEOTEST ® RN includes:• basic instrument Rheometer RHEOTEST ® RN (measuring head with highly dynamic measuring drive andcoupling for measuring systems, stand, gas spring and U-shaped support, control unit for power supply,control of measuring drive, data registration and communication, power cable, USB-Interface cable);• measuring systems (cylinder– and/or cone/plate and/or plate/plate) - according to the specific order; anoverview of all measuring systems supplied with the instrument is presented in the Overview MeasuringSystems;• installation data carrier with the software RHEOTEST RN 5 Manager for CR-, CS-, OSC-Tests and withmodule for temperature control - by concrete order;• packaging;• user manual;• PC and accessories (have to be ordered separately).3.2 Scope of Supply for DSR Bitumen Rheometer RHEOTEST ® RNThe scope of supply for a DSR – bitumen rheometer RHEOTEST ® RN consists of:• Basic instrument Rheometer RHEOTEST ® RN;• Peltier temperature control unit RHEOTEST ® PP (with power cable and USB-Interface cable) incl.tempered adapter for measuring systems cone-plate / plate-plate;• Peltier basic plate, two-sided tempered;• basic plate support;• exchangeable plate Ø 25 mm;• exchangeable plate Ø 8 mm ;• exchange grip;• measuring plate P3 (Ø 25mm);• measuring plate P4 (Ø 8mm);• set of trimming tools (1 spatula, 1 stripper gripper);• set of rubber moulds;• Phobya’s coolant with corrosion protection, if distilled water is used as a coolant. This agent must bediluted with water in the ratio: 5% of the agent and 95% of the water.4 Unpacking and CheckingAfter removing the device and accessories of packaging, please check their completeness according to theattached delivery note.In case of any transport damage, the carrier and RHEOTEST must be notified and receive a damage report.Before starting the operation read the Safety Instructions!8
5 Technical Manual5.1 Technical Specifications Rheometertorque range, mNm 0,1 … 150torque resolution, mNm 0,001angle range, µrad 0 … 5·10 6angle resolution, µrad 11,87angular velocity range, rad/s 0 … 210speed, rpm 0 … 2000speed resolution, rpm 0,015angular frequency range, rad/s 6,28·10 -5 … 628frequency range, Hz 0,001 ... 100temperature range, °C – 60* … +375**temperature range Peltier for PP4, °C –10 … +180***temperature range Peltier for PP5, °C –15 … +180***temperature resolution, °C 0,01normal force range, N – 30 … 30normal force resolution, N 0,01electrical supply from the AC mains:- voltage, V 110 … 240- frequency, Hz 49 ... 61power consumption, not more than, W 660dimensions (length, width, height), not more than, mm- basic instrument 235 x 240 x 570- control unit 130 x 295 x 350- Peltier control unit 180 x 300 x 460weight (net), kg- basic instrument 13,5- control unit 9,6- cable 0,5- Peltier control unit 11,5- adapter 1,7- plate/plate measuring system 8Note: The power supply must be protected with a maximum of 10 A!Notes:* For measurements at temperatures below –15°C an external cryostat is required.** The temperature range depends on the tempering system.*** When using the rheometer with plate-plate measuring systems and Peltier temperaturecontrol for basic plate, the following coolants are recommended:temperature range from -15°C to +120°C (from -10°C in the case of PP4) – coolant distilledwater (with corrosion inhibitor Phobya ZuperZero Xtreme);temperature range from 0°C to +180°C – coolant heat transfer fluid, e.g. FRAGOLTHERM ® X-T15 (based on polydimethylsiloxane).When using the rheometer with the cylinder measuring systems and Peltier temperaturecontrol, the following coolants are recommended:temperature range from -15°C to +150°C – coolant distilled water (with corrosion inhibitorPhobya ZuperZero Xtreme);temperature range from -5°C to +180°C – coolant heat transfer fluid, e.g. FRAGOLTHERM ®X-T15 (based on polydimethylsiloxane).9
Page 1 and 2: RHEOTEST Medingen GmbHOperation Man
Page 3 and 4: Contents1 Introduction ............
Page 5 and 6: 9.5.2.5.3 Print ...................
Page 7: 1 IntroductionThe Rheometer finds i
Page 11 and 12: 5.2.2 Adapter for a Rheometer with
Page 13 and 14: Figure 4 System of Exchangeable Mea
Page 15 and 16: 5.3 Control UnitThe on/off switch (
Page 17 and 18: 5.4.2 Cone/Plate and Plate/Plate Me
Page 19 and 20: 5.5 Peltier Tempering SystemThe pre
Page 21 and 22: Note: The Peltier control unit may
Page 23 and 24: • Then contact the energy supply
Page 25 and 26: 8 Test Preparation and Measurement8
Page 27 and 28: Figure 13 Setting up the Basic Plat
Page 29 and 30: Figure 15 Adapter5. Again, move dow
Page 31 and 32: 6. After clicking OK, the program r
Page 33 and 34: 8.2 Use Cylinder Measuring SystemsW
Page 35 and 36: 9 Software RHEOTEST ® RN 5 Manager
Page 37 and 38: 1 - Job Name: the job name should d
Page 39 and 40: 8 - use RN temperature only: Applic
Page 41 and 42: If communication between RHEOTEST
Page 43 and 44: 9.2.6.10 Table Settings -> CopyTabl
Page 45 and 46: directory name. Imported job’s gr
Page 47 and 48: Table heading makes possible to dis
Page 49 and 50: 3 - Min: Minimum value of X axis. D
Page 51 and 52: 5 - Grid Color: specifies the grid
Page 53 and 54: 5 - add Settings: It will be added
Page 55 and 56: Note: By a choice from the selectio
Page 57 and 58: 8 - Copy Test: The actual test is t
Page 59 and 60:
CS-Test decides on the start value
Page 61 and 62:
option gives an automatic concatena
Page 63 and 64:
Angle Abort Limit: 360°, not requi
Page 65 and 66:
In addition, the “Export / Import
Page 67 and 68:
9.7.1.1 Main menu Edit9.7.1.1.1 Edi
Page 69 and 70:
8 - Cancel: All changes will be rej
Page 71 and 72:
They will be updated when Service-J
Page 73 and 74:
7 - Phone: Input of phone number of
Page 75 and 76:
The following procedure exists for
Page 77 and 78:
12 - Cancel: All changes will be re
Page 79 and 80:
9.7.5 Pt100Pt100 calibration could
Page 81 and 82:
It will be printed maximal possible
Page 83 and 84:
10 Bitumen measurements10.1 General
Page 85 and 86:
DSR-Test (T-Sweep). The temperature
Page 87 and 88:
Please make sure that there is no s
Page 89 and 90:
- Resolve the knurled screw (2) (Fi
Page 91 and 92:
- Put the sample on the basic plate
Page 93 and 94:
All Jobs start with appropriate tem
Page 95 and 96:
data Gr. X Y meaning calculation un
Page 97 and 98:
MeterBinghamHerschel BulkleyCassonC
Page 99 and 100:
11.5 Calibration of measuring syste
Page 101 and 102:
11.7 Error messages11.7.1 Error mes
show all

Rheotest english

Create successful ePaper yourself

Delete template?

Save as template?