MANUAL PIEPS DSP | PIEPS DSP TOUR - Pieps-attack.ch
MANUAL PIEPS DSP | PIEPS DSP TOUR - Pieps-attack.ch
MANUAL PIEPS DSP | PIEPS DSP TOUR - Pieps-attack.ch
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ADDITIONAL FUNCTIONS FOR <strong>PIEPS</strong> <strong>DSP</strong><br />
The following additional functions are only valid for <strong>PIEPS</strong> <strong>DSP</strong>. The functions cannot be<br />
activated at <strong>PIEPS</strong> <strong>DSP</strong> Tour.<br />
1. SCAN-FUNCTION<br />
Press the SCAN button while in the SEARCH-mode. The <strong>PIEPS</strong> <strong>DSP</strong> will begin scanning the<br />
entire receiving range. During the scan, stand still and hold the device steady. This will give<br />
you an overview of all the buried devices within the detectable range, classified according to<br />
three groups:<br />
Reading 1: beacons within a distance of approx. 5m<br />
Reading 2: beacons within a distance of approx. 20m<br />
Reading 3: beacons within a distance of approx. 50m<br />
2. FREQUENCY MEASUREMENT<br />
Press the ENTER button while in the SEARCH-mode. The <strong>PIEPS</strong><br />
<strong>DSP</strong> uses the frequency measurement to <strong>ch</strong>eck the frequency of all<br />
other beacons. The frequency of the strongest (closest) beacon is<br />
measured. The deviation from the standardized frequency 457kHz<br />
is indicated. The shown number is the deviation in Hz and the<br />
arrows indicates + (right) or – (left).<br />
IMPORTANT! Check the transmitting frequency of your partners<br />
on tour regularly. According the standard EN300718 a beacon<br />
must transmit within the range of 457 kHz +/- 80 Hz. Ideal and<br />
reasonable te<strong>ch</strong>nical operation will have a maximum deviation of<br />
no more than +/- 30 Hz.<br />
IT FR ES EN DE<br />
All information from previously<br />
suppressed (MARKED) signals<br />
will be reset and you can start<br />
the suppression again (MARK)<br />
or follow the direction indication<br />
to the next strongest signal.<br />
IMPORTANT! Once you have<br />
located all burials, move away<br />
from their locations in a star<br />
shape and use the SCAN function<br />
to <strong>ch</strong>eck the scenario again. That<br />
way you can make sure you<br />
haven’t missed any other burials.<br />
3<br />
2<br />
1 One beacon<br />
within 5 m<br />
2 Two beacons<br />
within 20 m<br />
3 Four or more<br />
beacons within 50 m<br />
1<br />
3. SWITCHING FUNCTION TO TX600 SEARCH<br />
The <strong>PIEPS</strong> TX600 is a mini-transmitter for dogs<br />
and equipment that is transmitting out of the<br />
standard, EN300718 and can be received with<br />
every <strong>PIEPS</strong> <strong>DSP</strong> (Version 8.2). Press the ENTER<br />
and SCAN buttons simultaneously while in the<br />
SEARCH-mode. The <strong>PIEPS</strong> <strong>DSP</strong> swit<strong>ch</strong>es into<br />
the TX600-mode and indicates the direction<br />
and distance to the strongest TX600 signal. To<br />
activate the sear<strong>ch</strong> according to the standard<br />
EN300718 again, swit<strong>ch</strong> the <strong>PIEPS</strong> <strong>DSP</strong> to the<br />
SEND-mode and then back to the SEARCHmode.<br />
IMPORTANT! In the standard SEARCH-mode the <strong>PIEPS</strong> <strong>DSP</strong> does not indicate the TX600.<br />
Active sear<strong>ch</strong> operations are never influenced. A detection of the TX600 without swit<strong>ch</strong>ing to a<br />
special mode is only possible in immediate vicinity (