Toyota Child restraint seat - 73700-0W150 - Child restraint seat - Midi - mode d'emploi
Toyota Child restraint seat - 73700-0W150 - Child restraint seat - Midi - mode d'emploi
Toyota Child restraint seat - 73700-0W150 - Child restraint seat - Midi - mode d'emploi
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
RELEASING THE REAR CONNECTION HOOKS<br />
[MIDI_026] The Lexus or <strong>Toyota</strong> MIDI is attached<br />
to the ISOFIX BASE via connection hooks at the<br />
front and rear. To free the Lexus or <strong>Toyota</strong> MIDI<br />
from the ISOFIX BASE, you need only to release<br />
the rear hooks. The rear hooks unlock together, so<br />
you only need to push down one of the release<br />
elements on the exterior of the connection arms.<br />
The connection hooks have been correctly<br />
unlocked if you can see a red marking on the top<br />
of each release element. If green markings are<br />
shown, the hooks are still locked in place.<br />
4. USE IN THE VEHICLE<br />
WARNING!<br />
[MIDI_009] Never use the <strong>Toyota</strong> ISOFIX BASE<br />
on its own, or without properly securing the<br />
Lexus or <strong>Toyota</strong> MIDI. Failure to observe this<br />
notice may seriously risk your child’s safety,<br />
and the safety of other passengers.<br />
! Note: Long-term use of the <strong>Toyota</strong> ISOFIX<br />
BASE and Lexus or <strong>Toyota</strong> MIDI may result in<br />
wear and tear of the vehicle <strong>seat</strong>.<br />
Securing the <strong>Toyota</strong> ISOFIX BASE<br />
Step 1 Fold out the support leg<br />
Fold out the support leg as explained in Section 3<br />
– Basic instructions (Adjusting the support leg),<br />
and ensure that it is properly locked in place.<br />
Step 3<br />
Pull out the ISOFIX connectors<br />
[MIDI_023] Press in the button on the inner side of<br />
each rear connection arm as far as possible, and<br />
fully extend the connectors. Follow the instruction<br />
in Section 3 – Basic instructions (Adjusting the<br />
ISOFIX connectors).<br />
! Note: The connectors have been fully<br />
extended when no figure is displayed on the top<br />
of them.<br />
Step 4<br />
Connect the ISOFIX system<br />
[MIDI_028] Point the open ISOFIX connectors on<br />
the <strong>Toyota</strong> ISOFIX BASE towards the ISOFIX<br />
points of the vehicle. Slide the connectors into the<br />
vehicleʼs ISOFIX points, until each one clicks into<br />
place, and the green markings are visible on the<br />
release sliders.<br />
! Note: [MIDI_029] If the vehicleʼs ISOFIX<br />
points are difficult to reach, use the feeder<br />
supplied to guide them out. This makes connecting<br />
the system much easier, and protects the <strong>seat</strong><br />
cover.<br />
WARNING!<br />
Ensure that both ISOFIX connectors are<br />
fully secured to the vehicleʼs ISOFIX points.<br />
Failure to observe this notice may seriously<br />
risk your child’s safety, and the safety of other<br />
passengers. You can check the connectors<br />
are properly secured to the ISOFIX points, by<br />
lightly shaking the <strong>Toyota</strong> ISOFIX BASE.<br />
EN<br />
DE<br />
FR<br />
IT<br />
ES<br />
NL<br />
! Note: Check the support leg is locked in<br />
place by lightly shaking it with your hand.<br />
Step 2<br />
Place on the vehicle <strong>seat</strong><br />
[MIDI_027] Place the <strong>Toyota</strong> ISOFIX BASE on the<br />
<strong>seat</strong> of the vehicle.<br />
Ensure that:<br />
• The ISOFIX connectors are pointing to the<br />
back of the car <strong>seat</strong>.<br />
• The support leg is pointing to the vehicle<br />
floor.<br />
Step 5<br />
Fit the base against the back of the<br />
vehicle <strong>seat</strong><br />
[MIDI_030] Press the two buttons to adjust the<br />
length of the ISOFIX connectors and adjust them<br />
as recommended in your vehicle’s owner manual.<br />
If your <strong>seat</strong> back is adjustable, adjust it as<br />
recommended in your vehicle’s owner manual.<br />
In case there is no specific installation<br />
recommendation in your vehicle’s owner manual,<br />
push the ISOFIX BASE until it sits flush against<br />
the <strong>seat</strong> back.<br />
Lexus or <strong>Toyota</strong> MIDI 7