SCRUBTEC 545E – 553E - Wapalto-heine.de
SCRUBTEC 545E – 553E - Wapalto-heine.de
SCRUBTEC 545E – 553E - Wapalto-heine.de
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
USER MANUAL<br />
ENGLISH<br />
Brush/pad application gui<strong>de</strong> (suggestions only)<br />
Mo<strong>de</strong>ls MIDLITE GRIT 180 MIDGRIT 240 PROLENE PROLITE UNION MIX<br />
General cleaning:<br />
Concrete<br />
Terrazzo fl oor<br />
Ceramic tiles/quarrystones<br />
Marble<br />
Vinyl tiles<br />
Rubber tiles<br />
Polishing:<br />
Rubber tiles<br />
Marble<br />
Vinyl tiles<br />
Squeegee installation<br />
1. Install the squeegee (21) and fasten it with the handwheels (22), then connect the vacuum hose (11) to the squeegee.<br />
2. With the handwheel (23), adjust the squeegee so that the rear bla<strong>de</strong> - in all its length - touches the fl oor and the front bla<strong>de</strong> is<br />
slightly <strong>de</strong>tached from the fl oor.<br />
Solution tank filling<br />
1. Use the fi ller neck (34) to fi ll the tank (16) with a solution suitable for the work to be performed.<br />
Do not fi ll the solution tank completely, leave a few centimetres from the edge. Use the removable hose (13) as reference.<br />
Always follow the dilution instructions on the label of the chemical product used to prepare the solution.<br />
The solution temperature must not exceed 40°C.<br />
CAUTION!<br />
Use only low-foam and non-flammable <strong>de</strong>tergents, inten<strong>de</strong>d for automatic scrubber applications.<br />
MACHINE START AND STOP<br />
Starting the machine<br />
1. Prepare the machine as shown in the previous paragraph.<br />
2. Drive the machine to the working place by pushing it with the hands on the handlebar (2).<br />
3. Connect the power supply cable (3) to the electrical mains.<br />
4.<br />
5.<br />
6.<br />
7.<br />
8.<br />
9.<br />
WARNING!<br />
Before connecting the power supply cable to the electrical mains, check that frequency and voltage, shown on<br />
the machine serial number plate, match the electrical mains voltage.<br />
Lower the squeegee (21) with the lever (7).<br />
Lower the brush/pad-hol<strong>de</strong>r <strong>de</strong>ck by pressing the pedal (8).<br />
Press the brush/pad-hol<strong>de</strong>r switch (51) and the vacuum system switch (52).<br />
Press the washing water fl ow control switches (54) as necessary, <strong>de</strong>pending on the type of cleaning to be performed.<br />
To turn on the brush/pad-hol<strong>de</strong>r press one of the switches (55).<br />
Start cleaning, by moving the machines with the handlebar (2).<br />
Stopping the machine<br />
10. Stop the machine with the handlebar (2).<br />
11. Stop the brush/pad-hol<strong>de</strong>r by releasing the switches (55).<br />
12. Turn off the brush/pad-hol<strong>de</strong>r and the vacuum system by pressing the switches (51) and (52).<br />
13. Disconnect the power supply cable (3) from the electrical mains and place it on the hol<strong>de</strong>r (4).<br />
14. Lift the brush/pad-hol<strong>de</strong>r <strong>de</strong>ck by pressing the pedal (8).<br />
15. Lift the squeegee (21) with the lever (7).<br />
16. Make sure that the machine cannot move in<strong>de</strong>pen<strong>de</strong>ntly.<br />
9097056000(2)2009-06 A <strong>SCRUBTEC</strong> <strong>545E</strong> <strong>–</strong> <strong>553E</strong> 11