ACCESSORY LINE catalogue - Kendrion Binder

More documents

Recommendations

Info

Example of order phase-shift controller 33 43304B00 / 33 43303B00 10 phase-shift controllers Types 33 43304B00 + 33 43303B00 Function diagrams 33 43303B00 33 43304B00 CE The products comply with the EMC Directive 89/336/EEC. We declare compliance with the following standards: EN 55011 (VDE 0875, part 11, 1992) Group 1, class A conducted interference Group 1, class B radiated interference DIN EN 61000-4-3 (1995) severity level 3 DIN EN 61000-4-4 (1995) severity level 2 Severity level 3: Short-term, minor voltage increases can occur, but these do not result in any operational malfunctions. DIN EN 61000-4-5 (1995) severity level 3 The products comply with the Low Voltage Directive 73/23/EEC. We declare compliance with the following standards: HD625.1 S1 (1996) IEC 60529 (1991) The products are components in the meaning of the Machinery Directive 98/37/EC. According to this directive, such products incorporated in a machine may not be operated until said machine’s conformity with the EC directive has been established. We reserve the right to make changes to the product design. Please note ordering data! Mains ext. poti. ext. control signal Mains V Mains U Fine-wire fuse 5x20mm 2.5A/slo-blo Ammeter for measuring operating current when P1 ... Adjustment potentiometer adjusting load with trimmer P2 ... Trimmer S1 ... Short-circuit bridge for external potentiometer S2 ... Short-circuit bridge for external control S3 ... Short-circuit bridge for internal half-wave rectification Phase-shift controllers for installation on mounting rails Control These devices are suitable for controlling loads via an integral half-wave rectifier, both with variable AC and variable DC voltages. They are especially recommended for operating the KENDRION vibrators and vibrating solenoids of the OMV, OLV, OSR, OAB and OAC series as well as the WS3.. to WS9 series. Depending on the type, these devices can be controlled remotely via external potentiometers or PLC signals. They are protected against overloads by an internal fine-wire fuse. The vibration amplitude of the vibrators can be adjusted during operation by means of a potentiometer or (type 04B00 only) also by means of a PLC signal. www.kendrionmt.com Load ~ Load Load ~ Ramp generator Target value input 4-20 mADC / 2-10 VDC Electrical isolation Phase-shift controller Control input 0-28 VDC The type 04B00 has ramp functions and can compensate for input voltage fluctuations. The devices are fitted in space-saving plastic housings to facilitate easy mounting on top-hat rails in electrical cabinets.
phase-shift controllers 33 43303B00 components 33 43304B00 Technical specification Input voltage UI 100 - 240 V AC Frequency Adjustable output voltage (at 50 Hz): 40 - 60 Hz UOAC 0.2 - 0.95 x UI UODC 0.2 - 0.42 x UI Max. output current 2 AAC / 2 ADC Fuse fine-wire fuse, 5x20 T2.5E to DIN 41571 External potentiometer External control input: 500 kΩ / 0.5 W linear control voltage 24 V DC ± 10% max. control current 15 mA insulation voltage up to 2000 V polarity reversal protection included Ambient temperature range 0...50°C Connections 8-pole plug-in screw terminal Cross-section max. 1.5 mm 2 fine wire strands Mounting on 35 mm mounting rail to EN 50022 Short-circuiting bridges: DC voltage output S3 open external control input S2 open external potentiometer S1 open default setting all bridges short-circuited Class of protection to IEC 60529 IP 00 Control poti Mains We reserve the right to make changes to the product design. Please note ordering data! Cover www.kendrionmt.com L1 N N N AC AC L- L- I + P int IN Pext Vss IN EN GND Technical specification Input voltage UI 200 - 245 V AC Frequency Adjustable output voltage (at 50 Hz): 40 - 60 Hz UOAC (terminals N...AC) 0.2 - 0.95 x UI UODC (terminals N...L-) Output voltage stability 0.2 - 0.42 x UI in UI range ± 5% Max. output current 3 AAC / 2.5 ADC Fuse fine-wire, 5x20 M3, 15E to DIN 41571 External potentiometer 10kΩ / 1W Target value input 4-20 mADC / 2-10 VDC Control input max. 28 VDC Adjustable soft start and soft stop 80 ms to 1.2 s Ambient temperature -15...50°C Connection 2 plug-in screw terminals, each 8-pole Cross-section up to 2.5 mm2 fine wire strands Mounting on 35 mm mounting rail to EN 50022 Class of protection to IEC 60529 IP 00 We reserve the right to make changes to the product design. Please note ordering data! 11
Page 1 and 2: BINDER accessories accessories rect
Page 3 and 4: Types 32 073 Types 32 173 / 33 433
Page 5 and 6: technische rectifiers erläuterunge
Page 7 and 8: connectors/fork joints/fork pins GD
Page 9: switching devices Dimensions (mm) A

ACCESSORY LINE catalogue - Kendrion Binder

Create successful ePaper yourself

Delete template?

Save as template?