ACCESSORY LINE catalogue - Kendrion Binder

More documents

Recommendations

Info

6 27.5 35 7 GDSB211 27.5 52 M3 Ø 22.5 Type GDSB 211 plug-in connector DIN EN 175301-803 (DIN 43650-A) with integral rectifier GDSB 211 max. 230 VAC ±10% / 2 ADC order No: 314 1051 Plug-in connectors 2-pole plug-in connectors with PE line connection Plug-in connectors are detachable connections specially designed for electromagnetic devices. The 2-pole versions are used to connect single-direction linear solenoids and electromagnetic clamps. The cable outlet can be rotated through 4 x 90° by inserting the contact carrier accordingly. The plug-in connector is secured with a machine screw (supplied) after being plugged onto the device pins. This guarantees an effective seal between the plug-in connectors with rectifier 34 39 7 GDSBV211 34 18 M3 72 Type GDSBV 211 plug-in connector DIN EN 175301-803 (DIN 43650-A), protective varistor with integral rectifier GDSBV 211 max. 230 VAC ±10% / 4 ADC order No: 314 1049 two and prevents the connector from becoming accidentally detached. A screwed cable gland, thread size Pg 11 (GD209: Pg 9), serves to seal the cable entry. The contact elements are suitable for connecting wire cross-sections up to max. 1.5 mm 2 . Air clearance and leakage path to VDE 0110. Insulation class C. When plugged in and secured, the connection meets the requirements of class of protection IP 65 to IEC 60529. www.kendrionmt.com CE These components are not electronic or electrical devices in the meaning of the Machinery Directive 98/37/EC, but instead are merely intended for incorporation in other machines or systems, and are not for use by end-users. The user must guarantee that his end product complies with the appropriate directives. Low Voltage Directive 73/23/EEC. We declare compliance with the following standards: HD625.1 S1 (1996) IEC 60529 (1991 The products are components in the meaning of the Machinery Directive 98/37/EC. According to this directive, such products incorporated in a machine may not be operated until said machine’s conformity with the EC directive has been established. A manufacturer’s declaration can be obtained on request. Permissible continuous maximum temperature 90°C; the connection can withstand temperatures of up to 120°C briefly without suffering any damage. When using the GDSB 211 or GDSBV 211 plug-in connector with integral rectifier, the plug-in connector can be used as a direct connecting element between an AC mains system and a DC consumer. Four silicon diodes form a bridge circuit. A varistor connected in parallel on the AC side protects the bridge rectifier against voltage spikes from the mains.
connectors/fork joints/fork pins GD 311 GD 209 Fork joints to DIN 71752 27.5 35 7 27.5 52 M3 Ø 22.5 GD 311 (3-pole) form A order No. 314 1050 GD 209 (2-pole) form E order No. 314 1046 Fork joints Fork joints are used to connect all types of linear solenoids to force-transfer components such as levers, push bars, valve flaps, sliding dampers, etc. In many cases they enable rapid assembly during installation and also quick replacement of wear and spare parts. The fork joint is threaded to enable it to be screwed onto the pull or push bar of the linear solenoid, and is secured with a locknut. This type of fastening also represents an elegant and simple way of adjusting strokes and overcoming differences in length. Type GK 0 GK 1 GK 2 GK 3 GK 4 GK 5 GK 6 Order No. 3142005 3142007 3142009 3142011 3142013 3142019 3142021 a 8 8 10 12 16 20 24 b 4 4 5 6 8 10 12 c 8 8 10 12 16 20 24 d 1 4 4 5 6 8 10 12 Snap-on fork pins to DIN 71752 On versions without a snap-on fork pin, the force transfer between fork joint and actuating element is by way of a cylindrical pin fitted with the customary retaining components. When using a fork joint with a snap-on fork pin, this results in a quickly assembled and readily detachable connection (no tools required) between the linear solenoid and the actuating element. The spring clip ensures that the fork pin remains securely in position. The fork joints are electrogalvanised, the fork pins phosphatised. www.kendrionmt.com 7 d 2 M 3 M 4 M 5 M 6 M 8 M 10 M 12 d 3 8 8 9 10 14 18 20 l 1 21 21 26 31 42 52 62 l 2 16 16 20 24 32 40 48 l 3 6 6 8 9 12 15 18
Page 1 and 2: BINDER accessories accessories rect
Page 3 and 4: Types 32 073 Types 32 173 / 33 433
Page 5: technische rectifiers erläuterunge
Page 9 and 10: switching devices Dimensions (mm) A
Page 11 and 12: phase-shift controllers 33 43303B00

ACCESSORY LINE catalogue - Kendrion Binder

Create successful ePaper yourself

Delete template?

Save as template?