PowerValue 33

PowerValue TM – 33
TECHNICAL
SPECIFICATIONS
PowerValue TM 33
7.5-10-15-20-30-40kVA
Uninterruptible Power Supply (UPS)
On-Line, Double-Conversion, VFI
Newave_TDS_PowerValue_33_GB_060208.doc Page 1
Printed in Switzerland – Modifications reserved

PowerValue TM – 33
TECHNICAL SPECIFICATIONS
7.5, 10, 15, 20, 30 and 40kVA (three phase input and output)
GENERAL DATA
Output Rated Power kVA 7.5 10 15 20 30 40
Output Power Factor 0.8
Topology On-Line, Double Conversion, VFI, with static and maintenance bypass
Technology Third Generation, Transformerless
Double Conversion AC-AC efficiency with battery
fully charged
100%/75%/50%25% Linear Load (cos
phi=0.8ind)
100%/75%/50%/25% Linear Load (Resistive cos
phi=1)
100%/75%/50%/25% Non-linear Load
(EN 62040-1-1:2003)
Eco-mode efficiency (load on by-pass) at 100%
load
% 93.5/93.5/92/89 93.5/93.5/92/89 94/94/92.5/90 94.5/94.5/93/91 95/95/93.5/92 95/95/93.5/92
% 93/93/91.5/88.5 93/93/91.5/88.5 93.5/93.5/92/89.5 94/94/92/90 94/94/92.5/91 94/94/92.5/91
% 92/92/91/88 92/92/91/88 93/93/91.5/89 93/93/91/90 93/93/92/91 93/93/92/91
% 98 98 98 98
98 98
Heat Dissipation With 100% Load (cos phi=0.8ind) W 380 500 700 800 1200 1600
Heat Dissipation With 100% Load (Resistive cos
phi=1)
Heat Dissipation With 100% Non-linear Load
(EN 62040-1-1:2003)
Airflow (25° - 30°C) with Non-linear load
(EN 62040-1-1:2003)
W 400 550 750 960
W 460 600 800 1120
m 3 /h 110 110 150 200
1450 2000
1680 2400
300 600
Audible Noise with 100%/50% Load dBA 50/48 50/48 53/49 53/49 59/51 63/53
Ambient Temperature for UPS °C 0 – 40
Ambient Temperature for Batteries
(recommended)
°C
20 – 25
Storage Temperature of UPS °C -25 - +70
Battery Storage Time at Ambient Temperature Max. 6 months
Cooling Fan-assisted
Relative Air-humidity Max. 95% (non-condensing)
Standards
- Safety EN 62040-1-1:2003, EN 60950-1:2001/A11:2004
- Electromagnetic Compatibility
- Performance
EN 50091-2:1995, EN61000-3-2:2000, EN61000-3-3:1995/A1:2001,
EN61000-6-2:2001, EN61000-6-4:2001
EN62040-3:2001
Transportation Palette Provided with UPS
Packaging Cardboard (standard)
Accessibility Rear side access for Cabinet A, front side access for Cabinet B-C
Positioning Min. 10cm rear space (required for fan)
Input and Output Power Cabling From bottom rear (Cabinet A) and bottom front (Cabinets B and C)
Dry Port (Volt-free contacts) standard For Remote signalling and automatic computer shutdown
Smart Port (RS 232) For monitoring and integration in network management
Newave_TDS_PowerValue_33_GB_060208.doc Page 2
Printed in Switzerland – Modifications reserved

PowerValue TM – 33
RECTIFIER DATA
Input Voltage V 3x380/220V+N, 3x400V/230V+N, 3x415/240V+N
For Loads:

PowerValue TM – 33
POWER MANAGEMENT DISPLAY (PMD)
The user-friendly PMD consists of three parts the MIMIC DIAGRAM, CONTROL KEYS and LCD that provides
the necessary monitoring information about the UPS.
MIMIC DIAGRAM
The mimic diagram serves to give the general status of the UPS. The LED-indicators show the power flow
status and in the event of mains failure or load transfer from inverter to bypass and vice-versa the
corresponding LED-indicators will change colour from green (normal) to red (warning). The LED’s LINE 1
(rectifier) and LINE 2 (bypass) indicate the availability of the mains power supply. The LED’s INVERTER and
BYPASS if green indicate which of the two are supplying power to the critical load. When the LED-indicator
BATTERY is lit it means that the battery due to mains failure is supplying the load. The LED-indicator ALARM is
a visual indication of any internal or external alarm condition. At the same time the audible alarm will be
activated.
PUSHBUTTONS
The pushbuttons serve to manage the UPS by performing commands. The 2xON/OFF pushbuttons serve to
start-up or shutdown the UPS if pressed simultaneously. The pushbuttons UP and DOWN allow working
through the PMD-menu. The RESET pushbutton serves to cancel the audible alarm in the event of a
disturbance. If the alarm condition was only transient the LED-indicator ALARM would also extinguish otherwise
it will remain on (red).
DISPLAY
The 2 x 20 character LCD simplifies the communication with the UPS. The menu driven LCD enables the
access to the EVENT REGISTER, or to monitor the input and output U, I, f, P, Autonomy Time and other
Measurement’s, to perform commands like start-up and shut-down of INVERTER or load transfer from
INVERTER to BYPASS and vice-versa and finally it serves for the DIAGNOSIS (SERVICE MODE) for
adjustments and testing (for more details see the USER MANUAL of PowerValue TM ).
PowerValue
Line 2 Bypass
Line 1 Inverter
Power Management Display (PMD) of PowerValue TM
OPTIONALS
Remote Signalling Panel (RSP) including contact relay card For UPS-Status indication
Wavemon Software For automatic shut-down and monitoring
SNMP – Card/Adapter For network management and remote monitoring
Input Filter for THDI 7-9% For input harmonics reduction
ON REQUEST
Battery
RESET ENTER
Alarm
Input or Output Isolation Transformer For special voltages or for galvanic isolation
Customized UPS- and Battery Frames On request (for OEM-Projects only)
Newave_TDS_PowerValue_33_GB_060208.doc Page 4
Printed in Switzerland – Modifications reserved
ON/OFF
ON/OFF

PowerValue TM – 33
MECHANICAL CHARACTERISTICS PowerValue 33 Line
MODEL kVA 7.5 10 15 20 30 40
Dimensions (WxHxD) Cabinet A mm 340x820x800 Not available
Dimensions (WxHxD) Cabinet B mm 450x1250x860
Dimensions (WxHxD) Cabinet C mm 550x1650x890
Protection Degree IP 20
Ventilation Fan assisted
Colour RAL 9011
Foot Print m 2 0.25 0.37
Dimensions of PowerValue TM 33 Line
PowerValue TM : cabinet A
340mm
PowerValue TM : cabinet C *
550mm
820mm PowerValue TM : cabinet B
1250mm
1650mm
450mm
* Runtime calculated @ output power factor=0.8
For other battery configurations please refer to the
Weight & Dimensions Sheet
NOTE: if battery block number are below a total of
30 blocks only 7Ah batteries are allowed
Newave_TDS_PowerValue_33_GB_060208.doc Page 5
Printed in Switzerland – Modifications reserved
Rating
(kVA)
Standard battery
configuration
Max. runtime*
(min.) 100% load
Cabinet
Type
7,5 44 x 9Ah 20 A
10 46 x 9Ah 15 A
15 50 x 9Ah 10 A
7,5 3 x 40 x 7Ah 60 B
10 3 x 44 x 9Ah 60 B
15 3 x 46 x 7Ah 30 B
20 3 x 48 x 7Ah 20 B
30 3 x 46 x 9Ah 15 B
40 3 x 44 x 9Ah 10 B
15 2 x 36 x 28Ah 60 C
20 2 x 40 x 28Ah 60 C
30 2 x 40 x 28Ah 35 C
40 2 x 40 x 28Ah 22 C
*Please note that cabinet C is for non-standard autonomies requests

PowerValue TM – 33
Block Diagram PowerValue TM 33 Line
STANDARD VERSION (SINGLE INPUT FEED)
Fuse A
Cable A
FA3
PowerValue
Frame
Cable Sections and Fuse Ratings recommended by European standards.
Alternatively, local standards to be respected
STANDARD VERSION (SINGLE FEED INPUT)
Power (kVA) Fuse A (Agl/CB) Cable A (IEC 60950-1:2001) Cable D (IEC 60950-1:2001)
7.5 3x20 5x2.5 5x2.5
10 3x20 5x2.5 5x2.5
15 3x32 5x4 5x4
20 3x40 5x6 5x6
30 3x63 5x10 5x10
40 3x80 5x25 5x25
VERSION ON REQUEST (DUAL FEED INPUT)
Power
(kVA)
FA1
Rectifier
Inverter
Static Switch
IA2
Fuse B (Agl/CB)
MAINS (3x380V/220V,
3x400/230V,3x415/240V
FA2
UPS System 1
Mainten. Bypass
Load
Cable B
(IEC 60950-1:2001)
Fuse C
(Agl/CB)
Cable C
(IEC 60950-1:2001)
Cable D
(IEC 60950-1:2001)
7.5 3x20 5x2.5 3x20 4x2.5 5x2.5
10 3x20 5x2.5 3x20 4x2.5 5x2.5
15 3x32 5x4 3x32 4x4 5x4
20 3x40 5x6 3x40 4x6 5x6
30 3x63 5x10 3x63 4x10 5x10
40 3x80 5x25 3x80 4x25 5x25
DUAL INPUT FEED VERSION IS AVAILABLE ON REQUEST.
IA1
Cable D
VERSION ON REQUEST (DUAL INPUT FEED)
Fuse B Fuse C
Cable B
PowerValue
Frame
Mainten. Bypass
Cable D
MAINS (3x380V/220V,
3x400/230V,3x415/240V)
Newave_TDS_PowerValue_33_GB_060208.doc Page 6
Printed in Switzerland – Modifications reserved
FA3
FA1 FA2
Rectifier
Inverter
Static Switch
IA2
UPS System 1
Load
Cable C
IA1