Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
DRX-2<br />
16<br />
DRX-2<br />
Command overview Digital Board Chrysalis<br />
Below you will find an overview of the nuclei, their<br />
numbers, and their error codes. This overview is<br />
preliminary and subject to modifications.<br />
Chrysalis (CHR)<br />
Nucleus Name DS_CHR_DevTypeGet<br />
Nucleus Number 100<br />
Description Sends the device ID and the module ids and revisions of the PNX7100 (Chrysalis) to the<br />
stdout port.<br />
Technical - Determine the codec ID by means of comparing version ids of the modules.<br />
- Read the module-id register from every module.<br />
Execution Time Less than 1 second.<br />
User Input None<br />
Error Number Description<br />
10000 Getting the information succeeded<br />
10001 Wrong codec ID detected<br />
Example DS:> 100<br />
Device ID 7100<br />
Codec ID PNX7100_MF2<br />
F-BCU (0x0102) 1.0 INTC (0x011d) 1.0 PCI-XIO(0x0113) 1.0<br />
SIF(0x013b) 1.0 EJTAG (0x0104) 0.0 S-BCU (0x0102) 1.0<br />
BOOT (0x010a) 1.0 CONFIG (0x013f) 1.0 RESET (0x0123) 1.0<br />
DEBUG (0x0116) 0.0 UART0 (0x0107) 0.1 UART1 (0x0107) 0.1<br />
UART2 (0x0107) 0.1 UART3 (0x0107) 0.1 I2C0 (0x0105) 0.1<br />
I2C1 (0x0105) 0.1 GPIO (0x013c) 1.0 SYNC (0x013a) 1.0<br />
DISP0 (0xa015) 0.1 DISP1 (0xa00f) 0.0 OSD (0x0136) 0.1<br />
SPU (0xa00e) 0.0 MIXER (0x0137) 1.0 DENC (0x0138) 0.1<br />
CCIR (0x0139) 1.0 VDEC (0x0133) 0.1 PARSER (0xa00d) 0.0<br />
DV (0xa00c) 0.0 BEI (0xa00a) 0.0 IDE (0xa009) 0.0<br />
SGDX (0xa008)0.0 BYTE (0xa00b) 0.0 OUTPUT (0xa003) 0.0<br />
ACOMP (0xa000) 0.0 VFE (0xa001) 0.0 VCOMP (0xa002) 0.0<br />
SCR (0x0000) 0.0 SIFF (0xa011) 0.0 WMD (0xa010) 0.0<br />
AUDIO0 (0xa015) 0.1 AUDIO1 (0xa00f) 0.0 PSCAN (0xa018) 0.0<br />
010000:<br />
Test OK @<br />
Nucleus Name DS_CHR_TestImageOn<br />
Nucleus Number 101<br />
Description Generates a test-image of a selected video standard on selected video output on the digital<br />
board. When no input is given, the default values will be used. Use nucleus<br />
DS_ANAB_VideoRouting to route the video signal on the analog board output
Change language