9362588a, Operating Manual DVB Caravan Receiver ... - Kathrein
9362588a, Operating Manual DVB Caravan Receiver ... - Kathrein
9362588a, Operating Manual DVB Caravan Receiver ... - Kathrein
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Setting System Parameters<br />
64<br />
Tone burst<br />
DiSEqC<br />
DiSEqC Repeat<br />
UFO mini<br />
Remote frequency<br />
UFO micro<br />
Under this menu point, the 22 kHz signal can be set as follows:<br />
Switching statuses of setting: Switching statuses of setting: Switching statuses of setting:<br />
22-kHz signal —> High/Low<br />
and<br />
Tone Burst —> Pos. A/B:<br />
Low<br />
High<br />
Pos. 1<br />
Pos. 2<br />
22-kHz<br />
22-kHz<br />
Tone burst<br />
Tone burst<br />
Off<br />
On<br />
0<br />
1<br />
22-kHz signal —> Pos. A/B<br />
and<br />
Tone burst —> Opt. A/B<br />
Pos Tone burst 22-kHz Low<br />
High<br />
1<br />
0 Off<br />
2<br />
0 On Pos. 1<br />
3<br />
1 Off Pos. 2<br />
4<br />
1 On<br />
22-kHz signal —> Pos. A/B<br />
and<br />
Tone Burst —> High/Low<br />
Tone burst<br />
Tone burst<br />
22-kHz<br />
22-kHz<br />
If the receiver is connected to a DiSEqC switching matrix, you will<br />
need to set this menu point to ‘ON.’<br />
The switching criteria and the input assignments of the DiSEqC<br />
switching matrix must be maintained. Therefore, refer to the description<br />
of the switching matrices or contact the installer of the<br />
receiving system.<br />
The DiSEqC command must be repeated if the receiver is operated<br />
(cascaded) together with a receiving system with two or more DiSEqC<br />
switching matrices connected in a series.<br />
In this case, switch the menu point "DiSEqC repeat" to 1 or 2.<br />
Factory setting: ‘OFF’<br />
The input frequency of the receiver is fixed in a "user-controlled processing<br />
system". The signals from the "user-controlled processing system"<br />
are transmitted on this frequency. The reception parameters for<br />
programme selection are transferred to the receiving system by<br />
means of a DiSEqC command and set accordingly.<br />
The relevant setting, which needs to be selected, depends on the type<br />
of "user- controlled processing system".<br />
The setting should be made according to the data provided in the installation<br />
instructions for the "user-controlled processing system".<br />
If you have set the UFO mini menu point to ‘ON,’ you will need to set<br />
the transmission frequency under this menu point.<br />
Refer to the installation instructions of the "user-controlled processing<br />
system" for the set transmission frequency.<br />
Therefore, it is important to refer to the information provided in<br />
the installation instructions of the "user-controlled processing<br />
system".<br />
The setting under this menu point is also designed for operation of the<br />
receiver together with a processing system.<br />
Control and communication between the receiver and the <strong>Kathrein</strong><br />
UFO micro system occur via the return path of the coaxial cable. ‘ON’<br />
must be set under the UFO micro menu point, if the receiver is operated<br />
together with a UFO micro receiving system.<br />
During installation, the receiving system assigns a special address to<br />
the receiver so that the control instructions, which are sent from the<br />
0<br />
1<br />
Off<br />
On