Check out our NEW Catalog! - kolorMATRIX Screenprint Supply

Recommendations

Info

404-691-0055 404-691-0037fax www.freedkolormatirx.com 800-935-2121 404-691-0055 ww.kolormatrix.com Textile Ink WhItEs wHiTeS White Tiger GEN125 DESCRIPTION White Tiger is an extremely true, optically bright white ink formulated to give excellent printability across a range of screen printing applications.White Tiger's excellent opacity, fiber mat down, low gloss level, and good flash properties permit it to be utilized as both a stand-alone and an underbase white. PRINTER'S PARAMETERS Substrates 100% cotton, cotton blends, some synthetics Bleed resistance Good Mesh (on darks) 86-125 t/in Mesh (underbasing) 140-230 t/in Mesh (fine line) 195 to 305 t/in Squeegee type 60-80 durometer. Dual (70/90) or triple (70/90/70), Squeegee blade Slightly dulled (coarse mesh), sharp (fine mesh) Gel temp 160-180 F (71-82 C), Cure temp 320 F (160 C) entire film SPECIAL RECOMMENDATIONS · White Tiger is a low-bleed, NOT a non-bleed ink. · Avoid overflashing, as it can result in poor inter-coat adhesion of overprint colors. · Perform fusion tests before production. Failure to cure ink properly can result in poor wash fastness, inferior adhesion, unacceptable durability and increased likelihood of dye migration. GreatWhite GEN127 DESCRIPTION KolorMATRIXs GreatWhite is a low cost, high opaue, low bleed plastisol ink specifically formulated to address dye migration problems on a variety of specialty substrates. PRINTER'S PARAMETERS Substrates 100% cotton, cotton blends, some polyester Bleed resistance Excellent Mesh 60-130 threads/in Squeegee type 60-80 durometer, straight edge, Squeegee blade Hard, square, Squeegee angle Low angle Squeegee speed Hard flood, slow speed Gel temp 200 F , Cure temp 320 F entire film SPECIAL RECOMMENDATIONS · To optimize bleed resistance, set the dryer belt at the highest possible speed while still ensuring that the ink film reaches 320 F. This ensures that the ink's heat exposure is minimal. · Suggestions for automatic printing of GreatWhite: First print 130 mesh screen -- flash -- second print 86mesh screen. · On rare occasions, dye migration may occur. Cotton White GEN121 DESCRIPTION KolorMATRIXs Cotton White is a Super Opaque plastisol ink specifically formulated to print on 100% cotton. PRINTER'S PARAMETERS Substrates 100% cotton Bleed resistance NONE Mesh 60-130 threads/in Squeegee type 60-80 durometer, straight edge, Squeegee blade Hard, square, Squeegee angle Low angle Squeegee speed Hard flood, slow speed Gel temp 200 F , Cure temp 320 F entire film 20 FEATURES · Optically bright white · Ultra High Production enviroments, low build up and soft had are essential · Prints through fine meshes · Use as a first-down, underbase flash white or an overprint stand-alone white. · Good bleed resistance High Opaque Low Bleed Whites 200% Unconditional Guarantee 200% Unconditional Quality Assurance Guarantee! Try a kolorMATRIX Ink & if you don’t like it, we will credit your account, 200% of the price!! Cat# Description Pint Quart Gallon 5 Gallon GEN125 Tiger White 19.19 30.38 79.95 339.79 GEN127 Great White 13.19 20.88 54.95 233.54 Super Opaque White Gen121 Cotton White 10.79 17.08 44.95 191.04 You get much more than just low prices from Freedom.
WhItEs wHiTeS X2 White #ADV120 DESCRIPTION Advantage’s X2 is an optically bright white ink formulated to give excellent printability across a range of screen printing applications. Advantage’s X2’s excellent opacity, fiber mat down, low gloss level, and good flash properties permit it to be utilized as both a stand-alone and an under base white. PRINTER'S PARAMETERS Substrates 100% cotton, cotton blends, some synthetics Bleed resistance Good Mesh: on Darks 86-125 t/in , Underbasing 140-280 t/in , Fine line 195 to 355 t/in, Tension 15-20 acceptable, 25-35 recommended Stencil emulsion Direct, indirect & capillary Squeegee type 60-80 durometer. Dual (70/90) or triple (70/90/70), Squeegee blade: Sharp, Squeegee angle:Avoid excess pressure Squeegee speed Maximum Gel temp160-180 F, Cure temp:320 F entire film. Reducer 5 percent max (by weight) Curable Reducer #10070 SPECIAL RECOMMENDATIONS Advantage’s X2 is a low-bleed, NOT a non-bleed ink. A heavy pressure flood stroke that fully fills the open areas of the stencil with ink is recommended. For one-hit opacity through coarse meshes, use a coating procedure that builds a thick, even stencil to ensure a good column height of ink. To increase production speeds, use finer mesh counts for the flash plate to decrease gel time. Set flash dwell times on heated pallets to simulate production. Adjust your settings so that the ink is just dry to the touch. Avoid overflashing, as it can result in poor inter-coat adhesion of overprint colors. Perform fusion tests before production. Failure to cure ink properly can result in poor wash fastness, inferior adhesion, unacceptable durability and increased likelihood of dye migration. MaxPoly White #ADV150 DESCRIPTION Advantage’s MaxPolyWhite is a plastisol ink specifically formulated to address dye migration problems on a variety of specialty substrates. PRINTER'S PARAMETERS Substrates 100% cotton, cotton blends, 100% polyester Bleed resistance Excellent Mesh 60-130 threads/in Tension (newtons) 15-20 acceptable, 25-35 recommended Stencil emulsion Direct, indirect & capillary Squeegee type 60-80 durometer, straight edge, Squeegee blade Hard, square, Squeegee angle Low angle Squeegee speed Hard flood, slow speed Gel temp 200 F , Cure temp 320 F entire film SPECIAL RECOMMENDATIONS · To optimize bleed resistance, set the dryer belt at the highest possible speed while still ensuring that the ink film reaches 320 F. This ensures that the ink's heat exposure is minimal. · Suggestions for automatic printing of PolyWhite: First print 130 mesh screen -- flash -- second print 86mesh screen. · On rare occasions, dye migration may occur. Test print before production FEATURES · Optically bright white · Matte finish · Prints through fine meshes · Use as a first-down, underbase flash white or an overprint stand-alone white. · Good bleed resistance · Odorless 110% PRICE PROTECTION If you find a lower written price within 30 days, we will credit your account 110% of the difference. If you find lower pricing before you purchase, we will Discount Your price 110% of the difference!! * See page 1 for details FEATURES · Works well on heavy, colored aprons, dark athletic meshes & caps with heavy dye loads. · Use as a first-down, underbase flash white or an overprint stand-alone white. · Excellent bleed resistance, odorless · High opacity, good coverage High Opaque Low Bleed Whites Cat# Description Pint Quart Gallon 5 Gallon ADV120 X2 HOLBWhite 15.59 24.68 64.95 276.04 ADV150 Max Poly White 21.35 33.80 88.95 378.04 Pay By Credit or Debit Card & $ave 10% OFF - All Supplies in Catalog 21 404-691-0055 404-691-0037fax www.freedomkolormatrix.com 800-935-2121 404-691-0055 404-691-0037fax 800 Textile Ink
Page 1 and 2: HOT HOT NEW NEW Inks Inks kolor kol
Page 3 and 4: Important Information Company Infor
Page 5 and 6: No Suits... Recommended Product App
Page 7 and 8: UNICOAT High Gloss P.O.P UV screen
Page 9 and 10: HSB High Speed Bottle UV screen pri
Page 11 and 12: SPECIAL EFFECT INKS Upon request, w
Page 13 and 14: Product Description The CS Series i
Page 15 and 16: Generation Inks kolorMATRIX Generat
Page 17 and 18: STANDARD COLORS Cat# Description Pi
Page 19 and 20: POLY + COLORS Cat# Description Pint
Page 21: REDUCERS CURABLE REDUCER GEN 825 Vi
Page 25 and 26: Imported Low Low Elongation Mesh Me
Page 27 and 28: High Quality Wood Frames Our New Fr
Page 29 and 30: Degreaser SCP623 Liquid Degreaser A
Page 31 and 32: Instant Super Frame Adhesive An ins
Page 33 and 34: Squeegees Squeegees Squeegees Singl
Page 35 and 36: Black-Lite X-Po Exposure Unit • 2
Page 37 and 38: Heat Transfer Presses Presto 20 The
Page 39 and 40: Textile Ink Colors for Le$$ Yellow

Check out our NEW Catalog! - kolorMATRIX Screenprint Supply

Create successful ePaper yourself

Delete template?

Save as template?