Pages • Multi-Mat® Concept • Lamina Multi-Mat® full ... - Tikontools

ST-VBMT 060404L NN
Material Group
Low Carbon
Steel
Group Material Brinell
No Examples*
1
Ck 15
9SMnPb28
42 CrMo 4
Alloy Steel 2 100 Cr 6
High Alloy
Steel
32 NiCrMo 14.5
X38 CrMoV 5
3 X210 CrW 12
4
X90 CrMoV 8
hardness
HB
303 / 304 210
304 L to 250
Austenitic
230
5 316 / 316 L
Stainless Steel to 270
Ferritic
Stainless Steel
6
316 Ti
630 (F16PH)
*For all material types and standards, see pages 240 to 245.
Machining Conditions
d.o.c [mm] feed [mm/rev] A max Vc [m/min] Optimal cutting
[mm
min max min max
2 conditions
]
min max d.o.c feed
150 3.0
0.23 0.52 350
180 0.20 2.5 0.11 0.20 0.52 180 280 1 to 2.5 0.15
210 2.5
0.18 0.40 250
180 2.5
0.20 0.40 280
0.11
230
2.5
0.20 0.34
250
0.20
120
280 2.0
0.18 0.34 210
0.00
320 2.0
0.16 0.28 180
220 2.5
0.18 0.34 190
280
2.5
0.16 0.34
150
0.20
0.09
70
320 2.0
0.14 0.24 130
350 2.0
0.14 0.21 100
---------
0.20
7 430 / 439 / 444 Annealed 0.20
0.10
0.09
0.09
®
1 to 2.5 0.12
1 to 2.5 0.12
0.18 0.28 170 270 1 to 2.5 0.15
0.16 0.21 120 210 1 to 2.5 0.12
0.14 0.17 70 120 1 to2.5 0.11
0.18 0.24 170 250 1 to2.5 0.13
Martensitic
Annealed
170 250
8 410 / 420 0.20 2.0 0.11 0.18 0.24
Stainless Steel Treated 120 210
0.11
1 to2.5 0.13
EN - GJL 200
0.55 280
140
Grey Cast Iron 9 EN - GJL 250
0.20 3.0 0.10 0.23 0.52 170 250 1 to3 0.15
to 230
EN - GJL 300 0.52 230
Nodular Cast
Iron
Nickel Based
Alloys
Titanium Based
Alloys
EN - GJS 400 210 0.40 230
10 EN - GJS 600 260 0.20
0.20 0.35 120 190 1 to2.5 0.13
EN - GJS 800 310 0.35 150
Inconel 625 0.21 25 35
11 Inconel 718 -------- 0.20 2.0 0.09 0.16 0.21
12
Insert designation
ST-VBMT 060404L NN
2.5
2.0
2.0
2.0
2.5
Hastello y C 0.24 40 65
0.10
40 1 to2 0.12
TiAl 6 V4
0.16 0.24 35 60 1 to2 0.12
-------- 0.20 2.0 0.09
T40 0.14 0.21 28 40 0.0 0.10
Super Finishing Finishing Semi Finishing Roughing Interrupted Cut
2 3 4 2 3 4 2 3 4 2 3 4 2 3 4
28
Alu-Turning
LT-05 Aluminium Turning
Lamina's new and unique line of Turning inserts
for Aluminium and soft material machining. Based on
optimized chip breaker geometry and our unique
coated grade, LT-05.
Pages 116 to 123
Swiss
Made Machining Recommendations Guide - please see page 6
4 5
Alu-Line