Your Reliable DC and Gear Motor Supplier - Koco Motion GmbH

SHENZHEN KINMORE MOTOR CO.,LTD.
DC Motor Model Number Instruction
R S - 5 4 0 S H F V C 2 J 2 - 2 1 1 0 0 R
End cap type
A:Plastic end cap
H:Metal end cap
Accessories
F:Inside cooling fan
V:Varistor
C:Capacitor 2:2pcs
J:Choke 2:2pcs
Magnet type
R:C-shape isotropic magnet
T:Ring shape isotropic magnet
S:P.V.W:Anisotropic magnet or rare-earth magnet
C:Rubber magnet
Motor mdel: 5 4 0
5:Code number of armature diameter
N: 8.5 0: 9.35 1: 13.0 2: 15.0
3: 17.0 5: 23.0 7: 28.0 9: 34.0
4:Code number of housing length
0:Number of armature slots
0: 3 slots 5:5 slots 7: 7 slots 12:12 slots 16:8 slots
Brush type:
E.A.U.F:Precious metal brush
C.K.H.S.T:Carbon brush
Motor shape:
R:Round
F:Flat
S:Square
R:Flux ring
B:Multi-knurls
L: Four knurls
D:D-shape
G:Gear
U:Eccentric wheel
Magnet wire diameter and turn no. of armature
winding per slot
21: 0.21mm
100: 100 turns per slot
Note:
1.This instruction only applies to standard model.
2.The meaning of the numbers and letters might be different if
material or process is changed.
3.For more information, please feel free to contact Kinmore
sales engineer directly.
K M - 3 2 A 3 8 5 - 1 3 6 - 0 6 1 1 0
Company
Code
Gear Motor Model Number Instruction
Gear motor model
32:Gearbox max diameter 32mm
A: Shaft position
A: Inline B: Offset
L: 90 Degrees F: Parallel
385:DC Motor model number
Gear reduction ratio
136: 1/136
Nominal voltage and No load speed
06: 6V Nominal voltage
110: 110rpm No load speed

Customization:
1.Length A, B
2.Technical Data
3.Eccentric Wheel
4.Cable
Customization:
1.Length A, B
2.Technical Data
3.Eccentric Wheel
MODEL
KM-716N8D-L303045K0
KM-716N8F-L153040G0
MODEL
Your Reliable DC and Gear Motor Supplier
8.0REF
FF-N20VA-10150 R4.2*2.0
FF-N20VA-10150 R4.2*2.9
FF-N20VA-1476 R4.2*2.9
KM-716
Features: Typical Applications:
-NdFeB Magnet -Adult Toy
-Coreless Rotor -Massager
-Bi-direction -Cell Phone
-Stainless Steel Shaft -Beauty Apparatus
A±0.3 16.6±0.2 B±0.2
4.5±0.1
VOLTAGE
Start
RATED
OPERATING NOMINAL Voltage SPEED CURRENT LOAD
RANGE V V r/min A (Unit:mm) A
1.5-4.0 3 1.2 14000 0.16 R3*4.5 0.3
1.0-2.5 1.5 0.8 11500 0.2 R3*4 0.4
FF-N20VA
Features: Typical Applications:
-Tungsten Alloy Eccentric Wheel -Adult Toy
-Precious Metal Brush -Massager
-Stainless Steel Shaft -Beauty Apparatus
-Oil-impregnated Bearing
10.0
Positive Pole
0.05~0.35
END PLAY
VOLTAGE
Start
RATED
OPERATING NOMINAL Voltage SPEED CURRENT LOAD
RANGE V V r/min A (Unit:mm) A
3.0-5.0 3 0.7 12900 0.04 R4.2*2.0 0.6
3.0-5.0 3 0.7 12900 0.04 R4.2*2.9 0.6
1.0-2.0 1.5 0.4 12800 0.09 R4.2*2.9 0.95
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2.9
B±0.5
RED(+)
Bule(-)
A±0.3 15.1±0.2
2.5
DIRECTION OF ROTATION
CW/CCW
5.0
12.0
R3±0.1
7 +0.1
0
STALL
CURRENT
DIRECTION OF ROTATION
CW/CCW
STALL
CURRENT
Find even More at http://www.kinmoremotor.com Page [ 1 ]
2- 1.2
R4.2
8.5

Customization:
1.Length A, B
2.Technical Data
3.Eccentric Wheel
Customization:
1.Length A, B
2.Technical Data
3.Eccentric Wheel
MODEL
RF-1220CA-1856 φ7.0*5.0
RF-1220CA-06360 R6*4.8
MODEL
9.0REF
FF-030PK-10190 R6.0*9.6
FF-030PK-12140 R8.0*7.2
FF-030PK-12130 R7.0*4.8
FF-030PK-11150 R9.0*6.0
Your Reliable DC and Gear Motor Supplier
Positive Pole
Positive Pole
RF-1220CA
Features: Typical Applications:
-Copper Eccentric Wheel -Adult Toy
-Precious Metal Brush -Massager
-Stainless Steel Shaft -Cell Phone
GAP
VOLTAGE Start
RATED
OPERATING NOMINAL Voltage SPEED CURRENT LOAD
RANGE V V r/min A (Unit:mm) A
1.5-2.0 1.5 0.6 12800 0.8 φ7.0*5.0 2.3
3.0-8.0 7.4 1.8 7500 0.14 R6*4.8 0.28
FF-030PK
Features: Typical Applications:
-Galvanized Disk Eccentric Wheel -Adult Toy
-Precious Metal Brush -Massager
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
-Plastic End Cap -Game Controller
-Oil-impregnated Bearing -Beauty Apparatus
9.3REF
7.0
0.05~0.35
END PLAY
0.05~0.35
END PLAY
5.0 3.0±0.3
A
B
7.2 3±0.3
A
B
5
15.5
2-M2.0
STALL
CURRENT
VOLTAGE Start
RATED STALL
OPERATING NOMINAL Voltage SPEED CURRENT LOAD CURRENT
RANGE V V r/min A (Unit:mm) A
18.6
DIRECTION OF ROTATION
CW/CCW
3.0-4.0 3.5 1 5600 0.2 R6.0*9.6 0.55
3.0-4.0 3.5 1 6000 0.55 R8.0*7.2 0.55
2.0-3.0 2.5 1 6100 0.25 R7.0*4.8 0.85
2.0-4.5 4 1.3 6000 0.5 R9.0*6.0 0.75
20
5.0
DIRECTION OF ROTATION
CW/CCW
Find even More at http://www.kinmoremotor.com Page [ 2 ]
12.0
2- 1.4
12
8.5
30°
10

Customization:
1.Length A, B
2.Technical Data
3.Eccentric Wheel
Customization:
1.Length A, B
2.Technical Data
3.Eccentric Wheel
4.Cable
MODEL
FF-130PH-18130 φ10.0*6.0
FF-130PH-2065 φ10.0*3.5
MODEL
Your Reliable DC and Gear Motor Supplier
15.2
RF-300CA-12370 R10.5*8.4
3.38
FF-130H
Features: Typical Applications:
-Copper Eccentric Wheel -Adult Toy
-Precious Metal Brush -Massager
-Metal End Cap -Cell Phone
-Carbon Steel Shaft -Beauty Apparatus
Positive Pole
20.20°
VOLTAGE Start
RATED
OPERATING NOMINAL Voltage SPEED CURRENT LOAD
RANGE V V r/min A (Unit:mm) A
1.5-4.0 3 0.8 5700 0.28 φ10.0*6.0 1.7
1.0-4.0 3 0.8 10500 0.9 φ10.0*3.5 3.8
RF-300CA
Features: Typical Applications:
-Galvanized Disk Eccentric Wheel -Massager
-Precious Metal Brush -Game Controller
-Pancake Shape -Beauty Apparatus
-Oil-impregnated Bearing
VOLTAGE Start
RATED STALL
OPERATING NOMINAL Voltage SPEED CURRENT LOAD CURRENT
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
10.0
3.5
0.05~0.45 A
END PLAY
DIRECTION OF ROTATION
CW/CCW
R10.5
C±5
24.4MAX
6.1±0.1
B
25.0
12.5±0.15
A 0.5
8.4±0.3
B±0.5
DIRECTION OF ROTATION
CW/CCW
STALL
CURRENT
RANGE V V r/min A (Unit:mm) A
1.0-3.0 2 0.8 1750 0.14 R10.5*8.4 0.28
6.15
20.4
2.0 -0.003
-0.006
15.4
2-M2.0
12.4±0.05
Black (-) (+)Red
Find even More at http://www.kinmoremotor.com Page [ 3 ]

Customization:
1.Length A, B
2.Technical Data
3.Eccentric Wheel
Customization:
1.Length A, B
2.Technical Data
MODEL
RC-280SA-06360 R6.5*5.0
MODEL
RC-450SA-11700-44BU
RC-450SA-12580-44BU
Your Reliable DC and Gear Motor Supplier
RC-280SA
Features: Typical Applications:
-Copper Eccentric Wheel -Massager
-Carbon Brush -Car Power Seat
-Plastic End Cap -Cell Phone
-Carbon Steel Shaft
DIRECTION OF ROTATION
CW/CCW
14.0
VOLTAGE Start
RATED
OPERATING NOMINAL Voltage SPEED CURRENT LOAD
RANGE V V r/min A (Unit:mm) A
6.0-12.0 12 2 5000 0.07 R6.5*5.0 0.43
RC-450SA
Features: Typical Applications:
-Iron-Base Powder Metallurgy Eccentric Wheel -Massager
-Carbon Brush -Flour Sifter
-Plastic End Cap -Massage Armchair
-Ball Bearing On The End Cap Side
VOLTAGE Start
RATED STALL
OPERATING NOMINAL Voltage SPEED CURRENT LOAD CURRENT
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
13.0
4.0
2- 2.3
DIRECTION OF ROTATION
CW/CCW
6.05
2.0
5.0
11.5±0.5
1.7
STALL
CURRENT
RANGE V V r/min A (Unit:mm) A
6.0-12.0 12 2 1900 0.65 R17.5*11.5 0.5
6.0-24.0 24 2 4300 0.1 R17.5*11.5 1.5
45.0
30.5
(+)
(-)
17.5REF
24.0
Find even More at http://www.kinmoremotor.com Page [ 4 ]
8.5
8.0
12.9

Customization:
1.Length A, B
2.Technical Data
MODEL
FF-K10VA
Customization:
1.Length A, B
2.Technical Data
MODEL
FF-K20VA
12°
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-NdFeB Magnet -Note Book PC
-Precious Metal Brush -Optical Disk Drive
-Stainless Steel Shaft -Cell Phone
-Epilator
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
05220 2.0-4.0 3 23000 0.04 16300 0.09 0.05 0.5 0.09 0.17 1.7 0.2
07160 3.0-5.0 4.8 42995 0.07 34777 0.32 0.13 1.4 0.51 0.5 5.1 1.4
12°
1.0
FF-K10VA
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
1.0
(+)
(+)
8.0 +0.2
-0.1
0.30±0.03
8.0 +0.2
-0.1
FF-K20VA
VOLTAGE NO LOAD
Features: Typical Applications:
-NdFeB Magnet -Note Book PC
-Precious Metal Brush -Optical Disk Drive
-Stainless Steel Shaft -DVD & CD-ROM
-Oil-impregnated Bearing -Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
06205 2.0-3.5 3 11800 0.04 5800 0.1 0.147 1.5 0.07 0.27 2.8 0.16
07130 2.0-4.0 3.5 23800 0.04 18700 0.15 0.12 1.25 0.25 0.57 5.82 0.56
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
6.1
0.30±0.03
6.1
(-)
(-)
3.5±0.05
3.5±0.05
1.0 +0
-0.1
1.0 +0
-0.1
A±0.3
A±0.3
0.5
0.5
A±0.5
10.0±0.3
A±0.5
14.5±0.3
3.5±0.1
3.5±0.1
AT MAXIMUM EFFICIENCY
6.0 +0.1
-0.2
DIRECTION OF ROTATION
CW/CCW
6.0 +0.1
-0.2
5.4±0.05
M1.2*P0.25 TAPPED 2PLACE
SCREW LENGTH MAX 0.8mm
DIRECTION OF ROTATION
CW/CCW
5.4±0.05
M1.2*P0.25 TAPPED 2PLACE
SCREW LENGTH MAX 0.8mm
STALL
Find even More at http://www.kinmoremotor.com Page [ 5 ]

Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
FF-M10VA
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
FF-M20VA
7.3REF
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-NdFeB Magnet -Blood Pressure Pump
-Precious Metal Brush -Card Reader
-Stainless Steel Shaft -Camera
-Oil-impregnated Bearing -Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
06230 2.0-5.0 4.5 23200 0.065 17500 0.14 0.098 1 0.2 0.39 4 0.3
09120 1.0-3.0 1.5 14000 0.12 6000 0.3 0.157 1.6 0.08 0.25 2.6 0.45
7.3REF
Positive Pole
FF-M10VA
VOLTAGE NO LOAD
Positive Pole
GAP
FF-M20VA
VOLTAGE NO LOAD
AT MAXIMUM EFFICIENCY
Features: Typical Applications:
GAP
-NdFeB Magnet -Blood Pressure Pump
-Precious Metal Brush -Camcorder
-Stainless Steel Shaft -Electric Shaver
-Oil-impregnated Bearing -Toy
STALL
AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
08130 2.0-3.0 3 15200 0.045 11800 0.16 0.16 1.6 0.19 0.69 7 0.55
07170 1.5-3.0 2 8000 0.025 6000 0.075 0.09 0.9 0.06 0.35 3.6 0.23
10100 1.5-4.0 2.8 18000 0.05 14800 0.19 0.2 2 0.3 1.1 11 0.88
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
4.0±0.05
1.0 +0
-0.1
0.05~0.35
END PLAY
4.0±0.05
1.0 +0
-0.1
0.05~0.35
END PLAY
B±0.3
B±0.3
A ±0.5
0.6
0.6
11.8±0.2
A ±0.5
15.0±0.2
4.0±0.1
10.0±0.1
4.0±0.1
DIRECTION OF ROTATION
CW/CCW
2-M1.4
SCREW LENGTH
MAX 0.8mm
10.0±0.1
8.0±0.1
8.0±0.1
7.2±0.05
DIRECTION OF ROTATION
CW/CCW
2-M1.4
SCREW LENGTH
MAX 0.8mm
Find even More at http://www.kinmoremotor.com Page [ 6 ]
7.2±0.05

客户可定制:
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-NdFeB Magnet -Blood Pressure Pump
-Precious Metal Brush -Camcorder
-Stainless Steel Shaft -Electric Shaver
-Oil-impregnated Bearing -Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
FF-1012TA 07215 2.0-4.0 3 12900 0.055 10300 0.11 0.1 1 0.11 0.4 4 0.38
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
7.3REF
Positive Pole
FF-1012TA
VOLTAGE NO LOAD
7.3REF
Positive Pole
VOLTAGE
GAP
FF-1016VA
AT MAXIMUM EFFICIENCY
Features: Typical Applications:
-NdFeB Magnet -Blood Pressure Pump
-Precious Metal Brush -Camcorder
-Stainless Steel Shaft -Electric Shaver
-Oil-impregnated Bearing -Toy
NO LOAD AT MAXIMUM EFFICIENCY
STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
FF-1016VA 07190 2.0-4.0 3 8700 0.04 7200 0.085 0.1 1 0.07 0.45 4.5 0.28
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
GAP
4.0±0.05
4.0±.05
1.0 +0
-0.1
0.05~0.35
END PLAY
1.0 +0
-0.1
A ±0.3 12.5±0.2
8.0±0.1
0.6
0.6
B±0.5
A±0.5
0.05~0.35
END PLAY
B±0.3 16.0±0.2
8.0±0.1
4.0±0.1
4.0±0.1
10.0±0.1
10.0±.1
DIRECTION OF ROTATION
CW/CCW
2-M1.4
STALL
DIRECTION OF ROTATION
CW/CCW
SCREW LENGTH
MAX 0.8mm
2-M1.4*0.3
SCREW LENGTH
MAX 0.8mm
Find even More at http://www.kinmoremotor.com Page [ 7 ]
7.2±0.05
7.2±0.05

Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-NdFeB Magnet -Car CD/MD Player
-Precious Metal Brush -Optical Disk Drive
-Stainless Steel Shaft -Camera
-Oil-impregnated Bearing -Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
FF-N10VA 10140 2.0-4.0 3 16000 0.046 13000 0.18 0.25 2.5 0.33 1.18 12 0.8
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
FF-N20VA
7.0REF
FF-N10VA
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
7.0REF
Positive Pole
Positive Pole
0.05~0.35
END PLAY
FF-N20VA/TA
Features: Typical Applications:
-NdFeB Magnet -Blood Pressure Pump
-Precious Metal Brush -Door Lock Actuator
-Stainless Steel Shaft -Electric Shaver
-Oil-impregnated Bearing -RC Model/Toy
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
05240 3.0-12.0 12 16100 0.015 12240 0.06 0.3 3 0.37 1.2 12 0.21
08260 2.0-5.0 5 14600 0.03 11800 0.11 0.26 2.6 0.31 1.3 13 0.47
FF-N20TA 2818 0.8-1.5 12 34000 0.7 31000 1.4 0.2 2 0.64 1.6 16 6
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
A±0.5
DIRECTION OF ROTATION
2-2.0
0.6
CW/CCW
2-M1.4
4.0±0.05
1.0 +0
-0.1
1.0 +0
-0.1
0.05~0.35
END PLAY
B±0.3 13.1±0.2
B±0.3 15.5±0.2
5.0±0.1
12.0±01
5.0±0.1
12.0±01
10.0±0.1
10.0±0.1
SCREW LENGTH
MAX 0.8mm
A±0.5
DIRECTION OF ROTATION
2-2.0
0.6
CW/CCW
4.0±0.05
8.5±0.05
2-M1.4
SCREW LENGTH
MAX 0.8mm
Find even More at http://www.kinmoremotor.com Page [ 8 ]
8.5±0.05

Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
FF-N30VA
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-NdFeB Magnet -MD/CD Player
-Precious Metal Brush -Blood Pressure Meter
-Stainless Steel Shaft -Camera
-Oil-impregnated Bearing -RC Model/Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
06320 2.0-5.0 4.6 5300 0.01 4100 0.03 0.18 1.8 0.08 0.8 8 0.11
08250 2.0-6.0 5 7600 0.011 7600 0.06 0.3 3 0.23 0.15 15 0.26
FK-N30TS 2427 2.0-4.2 3.7 38000 0.38 30000 2.6 0.12 12 0.074 5.9 60 7
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
7.0REF
9REF
Positive Pole
FF/FK-N30VA
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
Positive Pole
0.05~0.35
END PLAY
RF-1215CA
B±0.3 20.1±0.2
Features: Typical Applications:
-NdFeB Magnet -Door Lock Actuator
-Precious Metal Brush -Tooth Brush
-Stainless Steel Shaft -Camera
-Oil-impregnated Bearing -Toy
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RF-1215CA 10150 1.0-3.0 2.5V 19500 0.13 12300 0.32 0.2 2 0.25 0.56 5.6 0.72
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
A±0.5
DIRECTION OF ROTATION
2-2.0
0.6
CW/CCW
GAP
4.0±0.05
1.0 +0
-0.1
5±0.05
1.5 +0
-0.01
0.05-0.35
END PLAY
B±0.3
15±0.2
5.0±0.1
5±0.1
12.0±01
12±0.1
2- 1.4
10.0±0.1
2-M1.4
SCREW LENGTH
MAX 0.8mm
STALL
A±0.5
DIRECTION OF ROTATION
1.0 CW/CCW
8.5±0.05
STALL
Find even More at http://www.kinmoremotor.com Page [ 9 ]
8.5±0.05

Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
RF-1220CA
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
9REF
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-NdFeB Magnet -Door Lock Actuator
-Precious Metal Brush -Tooth Brush
-Stainless Steel Shaft -Massager
-Oil-impregnated Bearing -Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
08230 2.0-5.0 5 14000 0.04 9800 0.15 0.31 3.1 0.31 1.08 11 0.35
1395 1.0-3.0 2.4V 15500 0.14 10000 0.46 0.39 4 0.41 1.18 12 1.1
9REF
Positive Pole
RF-1220CA
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
Positive Pole
0.05-0.35
END PLAY
RF-1230CA
B±0.3
Features: Typical Applications:
-NdFeB Magnet -Door Lock Actuator
-Precious Metal Brush -Tooth Brush
-Stainless Steel Shaft -Massager
-Oil-impregnated Bearing -Toy
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RK-1230CA 1855 1.0-3.5 3 15800 0.17 13200 0.45 0.5 5 0.68 2.94 30 2.3
RF-1230CA 1950 1.0-2.0 1.5 9500 0.11 7200 0.39 0.4 4 0.3 1.67 17 1.3
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
GAP
GAP
5±0.05
0.05-0.35
END PLAY
5±0.05
1.5 +0
-0.01
1.5 +0
-0.01
B±0.3
1.0
1.0
A±0.5
A±0.5
20±0.2
30±0.2
5±0.1
12±0.1
5±0.1
DIRECTION OF ROTATION
CW/CCW
12±0.1
2- 1.4
2- 1.4
8.5±0.05
DIRECTION OF ROTATION
CW/CCW
8.5±0.05
Find even More at http://www.kinmoremotor.com Page [ 10 ]

Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
RF-020CH
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Permanent Magnet/NdFeB Magnet -Radio Control Model
-Precious Metal Brush -Servo Mechanism
-Stainless Steel Shaft -Electric Shaver
-Oil-impregnated Bearing -Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
09215 3.0-5.0 4.5 12600 0.06 8800 0.17 0.39 3.9 0.34 0.13 13 0.48
10200 3.0-5.0 4.5 12600 0.05 10000 0.16 0.39 3.9 0.4 0.19 19 0.73
RK-020SH 10360 3.0-12.0 12.0 14000 0.07 13000 0.13 0.5 5 0.67 5.88 60 0.9
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
FF-030PA
0.3
11.8REF
Positive Pole
VOLTAGE
GAP
Positive Pole
RF/RK-020H
0.05~0.45
END PLAY
NO LOAD
FF-030PA/PK
AT MAXIMUM EFFICIENCY
Features: Typical Applications:
-Permanent Magnet -Blood Pressure Meter
-Precious Metal Brush -CD/DVD-ROM Drive
-Stainless Steel Shaft -'Electric Lock
-Oil-impregnated Bearing -Game Controller
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
11155 2.0-4.0 3 7200 0.045 5500 0.17 0.49 5 0.28 2.06 21 0.59
1592 2.0-4.0 3.5 14300 0.09 12500 0.3 0.49 5 0.64 3.92 40 2
FF-030PK 05440 3.5-12.0 12 11000 0.02 7800 0.065 0.49 5 0.4 1.67 17 0.18
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
4-1.0
2.0
9.3REF
4.7±0.05
6.15±0.05
1.5 +0
-0.01
0.05~0.35
END PLAY
1.5 +0
-0.01
B±0.3
B±0.3
A±0.5
1.6
17.8
A ±0.5
1.5
18.6±0.2
4.7±0.1
17.1±0.1
1.4
5±0.1
15.5±0.1
DIRECTION OF ROTATION
CW/CCW
2.0
2-M2.0
Screw Length
Max 0.8mm
15.8±0.1
13.2±0.1
STALL
DIRECTION OF ROTATION
CW/CCW
2-M2.0
SCREW LENGTH
MAX 0.8mm
12±0.1
Find even More at http://www.kinmoremotor.com Page [ 11 ]
30°
10.2±0.05
10±0.05

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FF-031VA
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
FF-050PH
Positive Pole
Your Reliable DC and Gear Motor Supplier
FF-031VA
Features: Typical Applications:
-Permanent Magnet -Blood Pressure Pump
-Precious Metal Brush -Electric Lock
-Stainless Steel Shaft -Camera
-Oil-impregnated Bearing -Toy
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
08310 2.0-4.0 3.0 4000 0.012 2700 0.055 0.3 3 0.08 0.9 9.1 0.15
09230 2.0-4.0 3.0 4000 0.025 3200 0.075 0.3 3 0.1 1 10 0.3
12125 3.0-8.0 7.4 19200 0.07 17500 0.25 0.5 5 0.9 4.1 42 1.8
12.3REF
10.0REF
0.3
FF/FK-050PH/TS
Features: Typical Applications:
-Permanent Magnet -Electric Shaver
-Precision Metal Brush/Carbon Brush -CD/DVD-ROM Drive
-Stainless Steel Shaft -CD/DVD Player
-Oil-impregnated Bearing -Toy
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
12140 2.0-9.0 7 12500 0.06 9800 0.3 1.18 12 1.2 5.29 54 1.1
11170 2.0-9.0 7 10500 0.04 9300 0.12 0.49 5 0.48 4.51 46 0.8
FK-050PH 05430 3.5-24.0 24 13800 0.03 9200 0.14 1.1 11.2 1.06 3.33 34 0.23
FK-050TS 2434 2.0-4.2 3.7 16800 0.37 16300 0.6 0.49 5 0.84 17.6 180 7.45
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2
GAP
1.5
4.7±0.05
5.0±0.05
1.5 +0
-0.01
0.05~0.35
END PLAY
1.5 +0
-0.01
B±0.3
1.0
A ±0.5
20.0±0.2
Positive Pole
0.05~0.45
END PLAY
B±0.3
26.5±0.2
1.5
A±0.5
6.0
14.0±0.1
DIRECTION OF ROTATION
1.3
CW/CCW
45°
2.0REF 12.0±0.1
4.7±0.1
15.5±0.1
2-M2.0*0.4
SCREW LENGTH
MAX 0.8mm
30°
12±0.1
2-M1.4
SCREW LENGTH
MAX 0.8mm
DIRECTION OF ROTATION
CW/CCW
Find even More at http://www.kinmoremotor.com Page [ 12 ]
10
10.0±0.05

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
RF-130CH
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Metal End Cap -CD / DVD Player
-Oil-impregnated Bearing -Electric Shaver
-Precision Metal Brush -RC Model/Toy
-Carbon Steel/Stainless Steel Shaft
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
06730 6.0-24.0 24.0 10500 0.01 8200 0.08 1 10 0.84 4.41 45 0.24
12250 3.0-6.0 6.0 8000 0.03 8000 0.13 0.7 7 0.58 4.1 42 0.75
RF-130SH 13225 3.0-6.0 5.0 5800 0.03 5250 0.09 0.5 5 0.27 4.9 50 0.74
Customization:
1.Length A, B
2.Technical Data
3.Terminals Type
MODEL
RF-130H
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
RE-140A
Features: Typical Applications:
-Plastic End Cap -Motorized Toy
-Oil-impregnated Bearing -Motorized Plastic Model
-Precision Metal Brush/Carbon Brush -Massager
-Carbon Steel/Stainless Steel Shaft
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RE-140RA 2270 2.4-3.0 3 18500 0.36 14170 1.18 0.92 9.4 1.36 3.92 40 3.85
RE-140SA
0.3
11.8REF
GAP
Positive Pole
0.05~0.45
END PLAY
STALL
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
14230 4.5-6.0 6 12400 0.14 9560 0.47 1.19 12.1 1.19 5.2 53 1.59
13130 3.0-4.5 3 13500 0.27 10740 1.05 0.39 14 1.54 6.67 68 4.1
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
4-1.0
2.0
DIRECTION OF ROTATION
CW/CCW
10.0
16
2- 2.0
6.15±0.05
21.0±0.1
1.5 +0
-0.01
5REF
15REF
6.15
B±0.3
1.6
A±0.5
22.8±0.2
A±0.3
25.0±0.2
1.6
4.7±0.1
B±0.5
17.1±0.1
1.4
2.0
2-M2.0
DIRECTION OF ROTATION
SCREW LENGTH
MAX 0.8mm
CW/CCW
15.8±0.1
13.2±0.1
Find even More at http://www.kinmoremotor.com Page [ 13 ]
4
2.0 +0
-0.1
6.0
5.4
10.2±0.05

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FF-130PA
Your Reliable DC and Gear Motor Supplier
FF/FK-130H
Features: Typical Applications:
-Metal End Cap -Air Conditioning Damper Actuator
-Oil-impregnated Bearing -Electric Shaver
-Precision Metal Brush/Carbon Brush -RC Model/Toy
-Carbon Steel/Stainless Steel Shaft -Tooth Brush
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
16155 2.0-3.0 2.3 4000 0.07 2500 0.3 1.32 13.5 13.8 3.92 40 0.76
17145 3.0-6.0 6 11500 0.1 10000 0.39 1.27 13 1.33 10 102 2.3
FF-130SH 2356 1.5-3.0 3 12800 0.27 10337 1.13 1.9 19.4 2.08 10 102 4.75
FK-130PH 07555 6.0-9.0 7.19 2700 0.02 1999 0.05 0.8 8.16 0.17 3 30.6 0.15
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
FF-180PA
DIRECTION OF ROTATION
CW/CCW
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
VOLTAGE
12.4
CW/CCW
12.4
2-M2*0.4
FF/FK-180H
Features: Typical Applications:
-Metal End Cap -Mini Printer
-Oil-impregnated Bearing -Electric Shaver
-Precision Metal Brush/Carbon Brush -RC Model/Toy
-Carbon Steel/Stainless Steel Shaft -Tooth Brush
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
3036 1.0-2.0 1.2 5600 0.22 4100 1.1 1.86 19 0.8 6.9 70 3
2950 2.0-3.0 2.4 8000 0.16 7400 0.49 0.98 10 0.76 1.18 120 4.5
FF-180SH 17157 3.0-9.0 6 7500 0.07 6289 0.36 2.3 23.5 1.49 14 143 1.89
FF-180PH 3334 3.0-7.5 7 33000 0.65 28062 3.7 6.2 63.2 18.11 41.2 420 21
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
15.4±0.3
2-M2.0*0.4
DIRECTION OF ROTATION
15.4±0.3
6.15±0.1
6.15±0.1
A±0.3
25±0.3
Screw length 2.0max
A±0.3
32.1±0.3
SCREW LENGTH 2.0MAX
6.15±0.1
B±0.5
6.15±0.1
B±0.5
STALL
NO LOAD AT MAXIMUM EFFICIENCY STALL
1.7
2 +0
-0.005
2 +0
-0.005
2.0
P
2.0
P
1
1.7±0.1
Red mark"+"
20°
RED MARK"+"
20°
4.3REF
4.3REF
0.3THK
15.2REF
20.4±0.3
15.2REF
20.4±0.3
Find even More at http://www.kinmoremotor.com Page [ 14 ]
3.2
0.3THK

Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
4. Lead wires & Terminals for option
MODEL
RF-300CA
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Metal End Cap -CD/DVD-ROM Drive
-Oil-impregnated Bearing -Game Controller
-Precision Metal Brush -RC Model/Toy
-Stainless Steel Shaft -Massager
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
07900 2.0-4.0 3 1700 0.005 1200 0.02 0.2 2 0.025 0.7 7.1 0.055
08770 1.0-4.0 2.5 1600 0.006 1209 0.018 0.2 2 0.025 0.83 8.47 0.057
11440 1.0-3.0 2 2200 0.014 1813 0.048 0.26 2.6 0.05 1.1 11.4 0.165
Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
RF-310CA
RF-320CA
60°
VOLTAGE NO LOAD
18.1REF
VOLTAGE
RF-300CA
DIRECTION OF ROTATION
CW/CCW
RF-310/320CA
Features: Typical Applications:
-Metal End Cap -Vending Machine
-Oil-impregnated Bearing -CD/ DVD Player
-Precision Metal Brush -RC Model/Toy
-Stainless Steel Shaft -Massager
NO LOAD
AT MAXIMUM EFFICIENCY
AT MAXIMUM EFFICIENCY
STALL
STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
10552 1.5-12.0 12 8500 0.02 7800 0.05 0.49 5 0.4 6.37 65 0.61
11380 1.5-6.0 6 6080 0.03 4600 0.13 0.98 10 0.47 4.1 42 0.54
11470 3.5-5.5 4.5 3600 0.015 2941 0.07 0.58 5.9 0.17 3.1 31.6 0.29
17195 1.0-4.0 3 5800 0.04 5000 0.14 0.49 5 0.26 4.41 45 1.1
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
60°
GAP
16.5
1.5
6-M1.7 ×
0.35
+
6.4±0.05
16.5
2.0 +0
-0.1
0.05~0.45
END PLAY
C±5
24.4MAX
6.1±0.1
12.5±0.15
A±0.5
1.4
A±0.3
A 0.5
18.0±0.2
B±0.5
2.0 -0.003
-0.006
(+)
6.4±0.1
6.45 0 -0.06
6-M2.0
SCREW LENGTH
Max 0.8mm
Black (-) (+)Red
DIRECTION OF ROTATION
CW/CCW
15.0±0.05
Find even More at http://www.kinmoremotor.com Page [ 15 ]
24.4±0.1
60°
60°

Customization:
1.Length A, B
2.Technical Data
3. EMC/EMI Suppression
MODEL
RF-500TB
Customization:
1.Length A, B
2.Technical Data
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Plastic End Cap -Spray Machine
-Oil-impregnated Bearing -Soap Dispenser
-Precision Metal Brush/Carbon Brush -Fire Alarm
-Carbon Steel/Stainless Steel Shaft -CD/DVD Drive
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
07800 2.0-4.0 3 1300 0.007 1000 0.02 0.24 2.5 0.02 0.91 9.3 0.053
17280 2.0-4.0 3 2700 0.03 2297 0.13 1.12 11.4 0.28 6.7 68.4 0.66
18250 2.0-4.0 3 3100 0.03 2679 0.14 0.98 10 0.29 6.86 58.4 0.54
3. EMC/EMI Suppression
MODEL
RF-520TB
6-5.0
VOLTAGE
RF/RK-500TB
DIRECTION OF ROTATION
CW/CCW
60°±0.5°
RF/RK-520TB
VOLTAGE NO LOAD
Features: Typical Applications:
-Plastic End Cap -Cash Register
-Oil-impregnated Bearing -Vending Machine
-Precision Metal Brush/Carbon Brush -Spray Machine
-Carbon Steel/Stainless Steel Shaft -Egg Mixer
AT MAXIMUM EFFICIENCY
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
17360 6.0-12.0 12 6300 0.03 5406 0.18 2.98 30.4 1.76 21.9 224 1.17
20230 3.0-6.0 6 5000 0.04 4500 0.16 1.96 20 0.92 20.5 210 2.2
RK-520TB 17380 6.0-12.0 12 6000 0.03 5200 0.17 2.94 30 1.6 24.5 250 1.5
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
30°
2-M2.5*0.45
DIRECTION OF ROTATION
CW/CCW
6-M2.6*0.45
2.0 -0.002
-0.006
1.9 19.5±0.3
6.2 +0
-0.05
17.5
22.8
NO LOAD AT MAXIMUM EFFICIENCY
26
22 0.1
8.2±0.1
32.7
2 -0.004
-0.006
B±0.5
14.3±0.5
A±0.5
2.0 22.7
(+)
(-)
7.4
32.0±0.1
3.2±0.1
20.3±0.3
4.5 REF
Positive Pole("+")
STALL
Positive Pole (+)
STALL
Find even More at http://www.kinmoremotor.com Page [ 16 ]
3.4
7.5±0.1
33.0
7°REF
23.7

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Plastic End Cap -Motorized Plastic Model
-Oil-impregnated Bearing -Motorized Toy
-Precision Metal Brush/Carbon Brush -Hair Remover
-Carbon Steel Shaft -Massager
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
FA-130RA 2270 2.4-3.0 3 18500 0.36 14170 1.18 0.92 9.4 1.36 3.92 40 2.2
FA-130SA 14150 4.5-6.0 6 12400 0.14 9560 0.47 1.19 12.1 1.19 5.2 53 1.59
Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
DIRECTION OF ROTATION
CW/CCW
VOLTAGE NO LOAD
AT MAXIMUM EFFICIENCY
STALL
11.8±0.1
0.3THK
10.1REF
20±0.1
FA/FC-130A
FC-140A
Features: Typical Applications:
-Plastic End Cap -Rearview Mirror
-Oil-impregnated Bearing -Headlamp Adjuster
-Leaf Brush System -Mirror Adjuster
-Carbon Steel Shaft -RC Model/Toy
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
FC-140PA 11260 6.0-9.0 9 8100 0.07 6310 0.25 1.76 18 1.17 8.0 81.6 0.87
FC-140PA 17132 6.0-12.0 12 21500 0.21 17681 0.97 3.8 38.7 7.1 21.6 220 4.5
FC-140SA 10350 6.0-12.0 12 8200 0.045 6475 0.17 1.7 17.3 1.7 7.8 79.6 0.63
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
6.0
2.0 +0
-0.01
DIRECTION OF ROTATION
CW/CCW
15.4±0.3
16.6±0.1
20.2±0.3
10±0.1
B±0.5
1.7
2.2±0.3
25.0±0.2
A±0.3
25±0.3
5±0.1
A±0.3
6.15±0.1
B±0.5
1.7±0.1
(-)
2 +0
-0.005
2±0.1
P
9.0REF
10.0±0.1
3REF
VIEW K
(+)
9±0.1
Red mark"+"
Find even More at http://www.kinmoremotor.com Page [ 17 ]
4.0±0.1
15.2±0.1
K

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FT-140SA
Customization:
1.Length A, B
2.Technical Data
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Plastic End Cap -Rearview Mirror
-Oil-impregnated Bearing -Headlamp Adjuster
-Leaf Brush System -Mirror Adjuster
-Carbon Steel Shaft -RC Model/Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
10350 6.0-12.0 12 8200 0.045 6475 0.17 1.7 17.3 1.7 7.8 79.6 0.63
3.EMC/EMI Suppression
MODEL
FC-260SA
FT-140A
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
8518 6.0-12.0 12 5500 0.04 4050 0.11 1.5 15.3 0.66 5.9 60.2 0.31
2.0
DIRECTION OF ROTATION
CW/CCW
15.4±0.3
FC-260A
Features: Typical Applications:
-Plastic End Cap -Door Lock Actuator
-Oil-impregnated Bearing -Hair Trimmer
-Leaf Brush System -Hair Dryer
-Carbon Steel Shaft -Scanner
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
STALL
STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
14265 6.0-12.0 12 8700 0.05 7330 0.27 2.47 25.2 1.9 15.7 160.1 1.42
15215 6.0-12.0 12 10500 0.06 8894 0.33 2.7 27.5 2.52 17.7 181 1.83
16185 6.0-12.0 12 12300 0.08 10596 0.47 3.26 33.3 3.62 23.5 240 2.9
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2 +0
-0.005
DIRECTION OF ROTATION
CW/CCW
8.5
11.5
2-M2.6*0.45
0.15 A
18.3±0.3
2±0.2
B±0.5
6.15±0.1
1.7±0.1
A±0.3
A
27±0.3
25±0.3
1.6±0.1
4±0.1
2.2±0.1
B
2
12.6
RED MARK"+"
2-0.8 +0.2
+0
E
2:1
10±0.1
3.6REF
9
0.8±0.2
E
8.5±0.1
18.2
24±0.3
Find even More at http://www.kinmoremotor.com Page [ 18 ]
6.15±0.1
2 +0
-0.005
0.2THK
20.4±0.3
"+"

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FT-260SA
Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FK-260SA
11.5
Your Reliable DC and Gear Motor Supplier
FT-260A
DIRECTION OF ROTATION
CW/CCW
VOLTAGE NO LOAD
Features: Typical Applications:
-Plastic End Cap -Hair Trimmer
-Oil-impregnated Bearing -Door Lock Actuator
-Leaf Brush System -Rearview Mirror
-Carbon Steel Shaft -Fax Machine
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
17188 6.0-12.0 12 12000 0.11 10074 0.57 3.9 39.8 4.15 24.5 250 3
19134 6.0-12.0 8.4 11500 0.13 9463 0.6 3.3 33.66 3.27 18.6 190 2.8
CW/CCW
11.5
24±0.3
2- 2.3
0.15 A
FK-260A
VOLTAGE NO LOAD
Features: Typical Applications:
-Plastic End Cap -Door Lock Actuator
-Oil-impregnated Bearing -Rearview Mirror
-Leaf Brush System -Electric Shaver
-Carbon Steel Shaft -Scanner
2-M2.6*0.45
0.15 P
Screw length 2.5MAX
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
18120 3.0-6.0 6 10400 0.15 8486 0.6 2.48 25.3 2.24 14.4 147 2.94
10280 6.0-12.0 12 8600 0.05 7300 0.17 1.47 15 1.12 9.7 99 0.84
10300 6.0-24.0 24 17300 0.07 14100 0.31 2.84 29 4.19 15.5 158 1.38
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
24±0.3
DIRECTION OF ROTATION
8.6±0.1
18.3±0.3
1.2±0.1
AT MAXIMUM EFFICIENCY
27±0.5
A±0.3
27±0.3
3.5±0.1
A±0.3
2.0
B±0.5 4.5REF
6.15±0.1
B±0.5
6.15±0.1
1.6
1.6
PTC M
2 +0
-0.005
2 +0
-0.005
P
E View
STALL
AT MAXIMUM EFFICIENCY STALL
2:1
30°
18.3±0.3
0.4THK
15REF
Find even More at http://www.kinmoremotor.com Page [ 19 ]
8.6±0.1
6.3±0.1
2±0.2
1.2±0.15
RED "+"
E
3.2REF

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FC-280SA
Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FT-280SA
2.0
Your Reliable DC and Gear Motor Supplier
DIRECTION OF ROTATION
CW/CCW
FC-280A
VOLTAGE NO LOAD
Features: Typical Applications:
-Plastic End Cap -Door Lock Actuator
-Oil-impregnated Bearing -Hair Trimmer
-Leaf Brush System -Hair Curler
-Carbon Steel Shaft -Scanner
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
20155 6.0-14.0 13.5 13800 0.12 11610 0.48 3.18 32.4 4.2 30.7 313 3.42
8470 6.0-24.0 24 8250 0.04 6308 0.15 3.03 30.9 1.89 13 133 0.53
FT-280A
VOLTAGE NO LOAD
Features: Typical Applications:
-Plastic End Cap -Retractable Rearview Mirror
-Oil-impregnated Bearing -Door Lock Actuator
-Leaf Brush System -Hair Remover
-Carbon Steel Shaft -Vending Machine
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
3340 1.5-2.5 1.9 7850 0.35 6349 1.39 3.05 31.1 1.9 16 163 6.6
21130 6.0-12.0 12 13480 0.11 11706 0.73 4.6 46.9 5.69 35.3 360 4.8
18163 6.0-13.0 13 11800 0.12 9747 0.57 4.9 50 5.05 28.4 289 2.7
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
8.5
11.5
CW/CCW
2-M2.6*0.45
0.15 P
DIRECTION OF ROTATION
24±0.3
18.3±0.3
2
8.6±0.1
1.2±0.1
SLOT
AT MAXIMUM EFFICIENCY
30.5
3.5±0.1
A±0.3
30.5±0.3
A±0.3
B±0.5
6.15±0.1
1.6
PTC M
Varistor
B±0.5
2
2 +0
-0.005
VIEW E
2:1
Motor case
18.3±0.3
RED MARK"+"
STALL
8.6±0.1
AT MAXIMUM EFFICIENCY STALL
3.6REF
E
8.5±0.1
18.2
24±0.3
Find even More at http://www.kinmoremotor.com Page [ 20 ]
1.6
6.15±0.1
2 +0
-0.005
P
0.2THK
2±0.2
1.2±0.15
"+"

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FK-280SA
Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FK-290SA
Your Reliable DC and Gear Motor Supplier
DIRECTION OF ROTATION
CW/CCW
FK-280A
VOLTAGE NO LOAD
Features: Typical Applications:
-Plastic End Cap -Retractable Rearview Mirror
-Oil-impregnated Bearing -Door Lock Actuator
-Leaf Brush System -Hair Remover
-Carbon Steel Shaft -Vending Machine
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
4525 1.0-2.0 1.2 8670 0.73 6560 2.24 1.74 17.7 1.3 9.61 98 8.43
16245 6.0-12.0 12 7300 0.06 6027 0.29 3.4 34.6 2.15 19.5 198 1.35
5.8±0.2
2- 2.3
11.5
0.15 A
FK-290A
VOLTAGE NO LOAD
Features: Typical Applications:
-Plastic End Cap -Hair Curler
-Oil-impregnated Bearing -Hair Remover
-Leaf Brush System -Vending Machine
-Carbon Steel Shaft -RC Model
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
4039 1.5-4.5 3 9200 0.27 7934 1.69 4.3 43.8 3.59 31.4 320 10.6
13338 6.0-12.0 12 4100 0.04 3303 0.19 4 40.8 1.32 21 214.2 0.92
FK-290PA 18170 6.0-24.0 24 17000 0.11 14378 0.7 7.5 76.5 11.53 54.9 560 4.4
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
18.3±0.3
DIRECTION OF ROTATION
CW/CCW
2-M2.6*0.45
11.5
18.3±0.3
A±0.3
30.5±0.5
1.6
B±0.5
HOLE
AT MAXIMUM EFFICIENCY
A±0.3
36±0.3
SCREW LENGTH 2.5MAX
6.15±0.1
B±0.5
6.15±0.1
2 +0
-0.005
A
1.6
HOLE
2 +0
-0.005
A
E VIEW
2:1
0.4THK
STALL
AT MAXIMUM EFFICIENCY STALL
2.0
30°
2.0
VIEW E
0.4THK
4.5REF
30°
4.5REF
15REF
15REF
24±0.3
24±0.3
Find even More at http://www.kinmoremotor.com Page [ 21 ]
2:1
RED MARK"+"
6.3±0.1
3.2REF
RED MARK"+"
6.3±0.1
E
3.2REF
E

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Plastic End Cap -Motorized Plastic Model
-Oil-impregnated Bearing -Motorized Toy
-Precision Metal Brush/Carbon Brush -Massager
-Carbon Steel Shaft
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RC-260RA 10350 8.0-12.0 12 10000 0.04 8040 0.16 1.27 13 1.07 6.47 66 0.67
RE-260RA 2670 1.5-3.0 1.5 6300 0.16 5040 0.64 0.98 10 0.52 4.9 50 2.56
RC-260SA
08550 6.0-24.0 24 10000 0.033 8100 0.14 2.05 20.9 1.98 10.8 110 0.6
07675 6.0-24.0 24 8000 0.028 6216 0.1 2.4 24.5 1.19 10.8 110 0.34
Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
VOLTAGE
RE/RC-260A
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
14.0±0.1
DIRECTION OF ROTATION
CW/CCW
2- 2.3
DIRECTION OF ROTATION
CW/CCW
2-M2.6
23.8
RE/RC-280A
Features: Typical Applications:
-Plastic End Cap -Door Lock Actuator
-Oil-impregnated Bearing -Hair Clipper
-Precision Metal Brush/Carbon Brush -Massager
-Carbon Steel Shaft -RC Model
NO LOAD
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RE-280RA 2865 1.5 - 3.0 3 9200 0.16 7770 0.87 1.98 20.2 1.61 12.7 129 4.7
RC-280SA 2769 3.0-6.0 6 14000 0.236 11948 1.374 4.31 44 0.55 29.4 299.9 8
RC-280SA 20125 3.0-6.0 9 11600 0.118 9935 0.7 3.8 38.8 0.55 26.46 270 4.2
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
23.7
2.0 +0
-0.005
0.05~0.50
END PLAY
6.1
2.0 +0
-0.005
END PLAY
0.05~0.50
12.2±0.5
8.6±0.5
1.6REF 5.0REF
1.5MAX
1.6REF
30.6
45.0±0.1
27.1
5.0REF
8.2
8.2
2.0
2.0
AT MAXIMUM EFFICIENCY
17.0REF 0.3
3.0
24.0 "+"
3.0
STALL
"+"
STALL
Find even More at http://www.kinmoremotor.com Page [ 22 ]
0.3
17.0REF
24.0
7.8
7.8

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Metal End Cap -Air Conditioning Damper Actuator
-Oil-impregnated Bearing -Blood Pressure Meter
-Precision Metal Brush/Carbon Brush -RC Model
-Carbon Steel Shaft -Styling Brush
-Printer
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RF-370CA 061700 6.0-24.0 24 1320 0.003 1000 0.008 0.98 10 0.1 4.02 41 0.26
RF-370CH 20123 3.0-6.0 6 8000 0.07 6878 0.42 2.4 24.5 1.71 17 173 2.55
RC-370SH
Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
4730 3.0-5.0 4.5 17500 0.55 15199 3.63 7.2 73.4 11.51 55 561 24
18139 6.0-12.0 12 10000 0.13 8439 0.7 5.8 59.2 5.17 37.5 382.5 3.8
25 +0
-0.5
RF/RC-370H
DIRECTION OF ROTATION
CW/CCW
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
FS-360/365A
Features: Typical Applications:
-Plastic End Cap -Power Tools
-Sintered Bronze Bearing -Garden Pump
-Leaf Brush System
-3Slots / 5Slots Armature
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
FS-365SA 2347 6.0-14.0 13.5 21800 0.27 18400 1.46 6.4 65.28 12.32 41 418.2 7.9
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
17
25°
DIRECTION OF ROTATION
CW/CCW
4±0.2
2-M3.0*0.5
0.15 P
24.4±0.3
6.5±0.1
A±0.3
30.8±0.3
6.4±0.1
Screw length 2.8max
A±0.3
32.6±0.5
10 +0
-0.1
B±0.5
2.0±0.1
B±0.5
Hole
1.7
2.8±0.1
2.3 +0
-0.005
2.5±0.1
P
1.2
2 +0
-0.005
P
VIEW B
11±0.1
3.9REF
Red mark"+"
5.3REF
0.4THK
0.3THK
STALL
18.2REF
Red mark"+"
28.5 +0
-0.5
Find even More at http://www.kinmoremotor.com Page [ 23 ]
B

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
FS-380SA
Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
FS-380/385A
Features: Typical Applications:
-Plastic End Cap -Electric clipper
-Sintered Bronze Bearing
-Leaf Brush System
-3Slots / 5Slots Armature
VOLTAGE NO LOAD
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
4037 2.0-6.0 2.4 5600 0.45 4592 2 6 61.2 2.76 33 336.6 8.91
3550 2.0-6.0 3.6 6300 0.3 5493 1.79 6 61.2 3.3 43 438.6 10.4
11186 6.0-24.0 24 6600 0.06 5238 0.23 6.07 61.9 3.33 29.4 299.9 0.9
FS-390/395A
Features: Typical Applications:
-Plastic End Cap -Exhaust Fan
-Sintered Bronze Bearing -Headrest Regulation
-Leaf Brush System -Window lifter
-3Slots / 5Slots Armature
VOLTAGE NO LOAD
AT MAXIMUM EFFICIENCY STALL
STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
FS-390SA 18190 6.0-12.0 12 4500 0.11 3582 0.44 9 91.8 3..22 44 448.8 1.8
FS-390PA
16
DIRECTION OF ROTATION
16
CW/CCW
2-M3.0X0.5
3333 6.0-12.0 12 16000 0.38 13892 2.5 16 163.2 23.31 121.6 1240 16.5
19100 6.0-24.0 24 9500 0.14 8033 0.77 14.8 151 12.49 96.1 980.2 4.2
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
25 +0
-0.5
DIRECTION OF ROTATION
CW/CCW
2-M3.0X0.5
25 +0
-0.5
4±0.2
4±0.2
A±0.3
40±0.3
10 +0
-0.1
4.2±0.2
A±0.3
46.5±0.3
2.5±0.1
10 +0
-0.1
4.2REF
SCREW LENGTH2.8MAX
B±0.3
2.3 +0
-0.005
2.5±0.2
1.5REF
B±0.5
2.8±0.1
VIEW
2.3 +0
-0.005
AT MAXIMUM EFFICIENCY
A
5.3REF
0.4THK
2.8±0.1
VIEW
0.4THK
11±0.1
5.3REF
RED MARK“+”
28.5 +0
-0.5
B
22.5REF
RED MARK“+”
28.5 +0
-0.5
Find even More at http://www.kinmoremotor.com Page [ 24 ]
11±0.1
22.5REF
B

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring
4.EMC/EMI Suppression
MODEL
RS-360SA
RS-365SA
Customization:
1.Length A, B
2.Technical Data
3.Flux Ring
4.EMC/EMI Suppression
MODEL
RS-360SH
RS-365SH
16
Your Reliable DC and Gear Motor Supplier
RS-360/365A
Features: Typical Applications:
-Plastic End cap -Stick Massager
-Sintered Bronze Bearing -Air Freshener
-Leaf Brush System -Foot Bath/Hair Dryer
-3Slots / 5Slots Armature -Copy Machine/Printer
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
13370 6.0-12.0 12 4500 0.04 3716 0.19 3.75 38.3 1.46 21.5 220 0.9
11520 6.0-24.0 24 7100 0.05 5671 0.23 4.54 46.3 2.7 25.5 260 1.06
15113 6.0-12.0 12 7800 0.14 6153 0.52 5.59 57.3 3.6 26.5 270 1.96
8365 6.0-24.0 24 5420 0.033 4109 0.1 2.8 28.6 1.21 11.8 120 0.33
16
DIRECTION OF ROTATION
CW/CCW
2-M2.6*0.45
RS-360/365H
Features: Typical Applications:
-Metal End Cap -Stick Massager
-Sintered Bronze Bearing -Air Freshener
-Leaf Brush System -Foot Bath/Hair Dryer
-3Slots / 5Slots Armature -Copy Machine/Printer
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
16235 6.0-12.0 12 7300 0.15 5704 0.54 6.2 63.24 3.71 28.4 290 1.92
2585 3.0-6.0 6 10500 0.26 8752 1.3 5.16 52.6 4.73 30.9 316 6.5
9270 6.0-12.0 12 10300 0.058 8728 0.24 4.02 41 3.71 27.9 285 1.47
11210 6.0-24.0 24 8000 0.05 6389 0.2 4.74 48.3 3.17 23.5 240 0.79
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
27.7±0.3
22REF
0.4
10 0
-0.1
A±0.3
32.6±0.5
2.3REF
B±0.5
10 0
-0.1
P
2.8±0.1
8
Hole
Vent holes Vent holes
Screw length 2.8max
2.5
Vent holes
DIRECTION OF ROTATION
CW/CCW
27.7±0.3
2.0REF
22REF
10 0
-0.1
2-M2.6*0.45
0.15 P 0.4
A±0.3
32.6±0.3
10 0
-0.1
Screw length 2.8MAX
B±0.5
2.5
2.3 +0
-0.005
2.3 +0
-0.005
8
Hole
STALL
"+"
2.8±0.1
Find even More at http://www.kinmoremotor.com Page [ 25 ]
"+"
5.0REF
6.5REF

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring
4.EMC/EMI Suppression
MODEL
RS-380SA
RS-385SA
Customization:
1.Length A, B
2.Technical Data
3.Flux Ring
4.EMC/EMI Suppression
MODEL
RS-380SH
RS-385SH
16
Your Reliable DC and Gear Motor Supplier
DIRECTION OF ROTATION
Features: Typical Applications:
-Plastic End cap -Printer / Copy Machine
-Sintered Bronze Bearing -Automatic Cruise Control
-Leaf Brush System -Drill & Screwdriver
-3Slots / 5Slots Armature -Vacuum Cleaner
VOLTAGE NO LOAD
AT MAXIMUM EFFICIENCY
STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
3749 3.0-12.0 6 11000 0.39 9522 2.51 9.74 99.4 9.72 72.55 740 16.2
15265 6.0-24.0 24 9080 0.08 7730 0.4 9.36 95.5 7.52 59.3 605 2.49
11210 6.0-12.0 12 3100 0.03 2439 0.11 3.3 33.7 0.85 15.7 160 0.41
12175 6.0-24 24 7000 0.06 5750 0.25 6.52 66.5 3.91 36.8 375 1.27
16
VOLTAGE
CW/CCW
RS-380/385A
VENT HOLES
0.15 P
RS-380/385H
Features: Typical Applications:
-Metal End Cap -Printer / Copy Machine
-Sintered Bronze Bearing -Automatic Cruise Control
-Leaf Brush System -Drill & Screwdriver
-3Slots / 5Slots Armature -Vacuum Cleaner
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
4052 3.0-6.0 4.8 7800 0.32 6701 1.95 9.9 101 6.98 70.6 720 11.9
3557 6.0-12.0 12 21200 0.44 18367 2.85 11.26 114.9 21.68 84.3 860 18.5
17110 6.0-24.0 24 11000 0.15 9034 0.69 10.7 109 10.12 59.8 610 3.16
2267 6.0-12 12 10000 0.17 8340 0.85 7.5 76.5 6.53 45 459 4.29
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
27.7±0.3
2-M2.6*0.45
DIRECTION OF ROTATION
CW/CCW
Vent holes
2-M2.6*0.45
29±0.3
2.5REF
22REF
10 0
-0.1
0.4
27.7±0.3
VENT HOLES
37.8±0.5
A±0.3
SCREW LENGTH2.8MAX
2.0REF
22REF
0.4
10 0
-0.1
Vent holes
A±0.3
37.8±0.3
2.8±0.1
VENT HOLES
NO LOAD AT MAXIMUM EFFICIENCY STALL
20
10 0
-0.1
4REF
Screw length 2.8max
10 0
-0.1
B±0.5
2.5
B±0.5
2.3 +0
-0.005
2.3 +0
-0.005
2.5±0.1
P
HOLE
Hole
8
2.8±0.1
Find even More at http://www.kinmoremotor.com Page [ 26 ]
"+"
8
"+"
5.0REF
6.5REF
4.5REF

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring
4.EMC/EMI Suppression
MODEL
RS-390SA
RS-395SA
Customization:
1.Length A, B
2.Technical Data
3.Flux Ring
4.EMC/EMI Suppression
MODEL
RS-390SH
RS-395SH
16
Your Reliable DC and Gear Motor Supplier
RS-390/395A
VOLTAGE NO LOAD
Features: Typical Applications:
-Plastic End cap -Headrest Adjuster/ Throttle Control
-Sintered Bronze Bearing -Drill & Screwdriver
-Leaf Brush System -Foot/Bath/Hair Dryer
-3Slots / 5Slots Armature -Vacuum Cleaner
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
4535R 6.0-9.0 9 17500 0.65 14909 3.74 15.2 155 23.81 103 1051 21.51
22128 6.0-12.0 12 7300 0.18 5972 0.81 10.5 107.1 6.58 57.9 590 3.65
2166 6.0-12.0 12 6900 0.18 5631 0.8 9.6 97.92 5.64 52 530 3.54
3132 6.0-12.0 12 16800 0.36 14406 2.08 11.59 118 15.91 78.4 800 12
16
DIRECTION OF ROTATION
CW/CCW
VENT HOLES
2-M2.6*0.45
DIRECTION OF ROTATION
CW/CCW
RS-390/395H
VOLTAGE NO LOAD
Features: Typical Applications:
-Metal End Cap -Headrest Adjuster/ Throttle Control
-Sintered Bronze Bearing -Drill & Screwdriver
-Leaf Brush System -Foot/Bath/Hair Dryer
-3Slots / 5Slots Armature -Vacuum Cleaner
2-M2.6*0.45
29±0.3
27.7±0.3
0.15 A
29±0.3
27.7±0.3
2.3REF
STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
20156R 6.0-12.0 12 5000 0.08 4243 0.33 6.07 61.9 2.72 42.2 430 2.22
2975 6.0-12.0 12 12000 0.29 10165 0.33 5.75 58.6 1.31 80.4 820 8.9
15130 6.0-12.0 12 3650 0.66 2949 0.25 5.83 59.5 1.8 30.4 310 1.06
15100R 6.0-24.0 24 10300 0.07 8893 0.38 7.09 72.3 6.68 54.9 560 2.66
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
22REF
10 0
-0.1
0.4
2.0REF
22REF
0.4
10 0
-0.1
VENT HOLES
A±0.3
46.5±0.5
28REF
4REF
SCREW LENGTH 2.8MAX
VENT HOLES
AT MAXIMUM EFFICIENCY
A±0.3
46.5±0.3
28REF
SCREW LENGTH 2.8MAX
10 0
-0.1
2.5
B±0.5
10 0
-0.1
B±0.5
2.3 +0
-0.005
2.5
HOLE
VENT HOLES
2.8±0.1
AT MAXIMUM EFFICIENCY STALL
Find even More at http://www.kinmoremotor.com Page [ 27 ]
A
2.3 +0
-0.005
HOLE
8
"+"
2.8±0.1
"+"
5.0REF
4REF
6.5REF
4.5REF

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Metal End Cap
-Cordless Power Tool
-Class F Magnet Wire -Window Lifter
-Leaf Brush System -Bilge Pump
-Carbon Steel Shaft
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
FS-540SH 4753R 3.0-9.0 6.4 6200 0.69 5160 2.19 18.8 192 9.71 93.1 950 13.7
FS-545SH
Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
FS-555SH
FS-540/545H
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
2586 6.0-12.0 12 4700 0.26 3670 0.93 15.3 156 5.86 69.6 710.2 3.3
21115 6.0-12.0 12 3800 0.12 2700 0.42 9.8 100 2.8 32.3 330 1.2
28
28
DIRECTION OF ROTATION
CW/CCW
Vent holes
2-M3.0*0.5
0.15 P
FS-550/555H
Features: Typical Applications:
-Metal End Cap
-Cordless Power Tool
-Class F Magnet Wire -Window Lifter
-Leaf Brush System -Air Pump
-Carbon Steel Shaft
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
3349 6.0-18.0 12 6000 0.1 5044 0.85 15 153 7.92 94.12 960 4.5
3154R 4.0-12.0 6 2700 0.18 2074 0.6 9.314 95 2.02 40.2 410 2
2764R 6.0-18.0 12 3780 0.13 2570 0.78 19.61 200 5.27 61.08 623 2.16
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
35.8±0.3
DIRECTION OF ROTATION
CW/CCW
Vent holes
37.8±0.3
2-M3.0*0.5
0.15 P
35.8±0.3
3.8±0.1
53±0.3
STALL
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
A±0.3
Vent holes
Screw length 3.5max
7REF
A±0.3
63±0.3
38REF
Vent holes
5REF
Screw length 3.5max
B±0.5
11.1±0.1
4
B±0.5
11.1±0.1
4 +0
-0.005 Red mark"+"
P
0.5THK
3.175 +0
-0.006
4±0.1
P
29±0.3
23.8±0.3
23.8±0.3
0.5±0.05
Red mark"+"
(+)
29±0.3
(-)
31.5±0.3
Find even More at http://www.kinmoremotor.com Page [ 28 ]

Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Plastic End Cap -Headrest Adjuster
-Class F Magnet Wire
-Vacuum Cleaner
-Leaf Brush System -Bilge Pump
-Carbon Steel Shaft -RC Model/Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RS-540SA 4552 6.0-12.0 12 13500 0.62 11633 3.09 22.71 232 28.32 184.3 1880 25.49
RS-540PA 23198 6.0-12.0 12 3500 0.12 2898 0.58 14.87 152 4.51 86.5 882.3 2.79
RS-545SA
Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
MODEL
3153 6.0-12.0 12 8000 0.28 6732 1.49 16.5 168 11.61 103.9 1060 7.9
21116 6.0-24.0 24 6600 0.12 5761 0.57 17.7 181 10.52 132.3 1350 4.13
Features: Typical Applications:
-Metal End Cap -Headrest Adjuster
-Class F Magnet Wire
-Vacuum Cleaner
-Leaf Brush System -Bilge Pump
-Carbon Steel Shaft -RC Model/Toy
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RS-540SH 6036 6.0-24.0 12 19500 0.95 16634 5.51 28.8 294 50.22 2000 196.1 32
RS-540PH 7021 6.0-8.0 7.2 20000 1.2 17317 7.75 22.3 228 40.5 166.5 1698 50
RS-545SH
RS-540/545A
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
25
25
DIRECTION OF ROTATION
CW/CCW
Vent holes
RS-540/545H
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
21105 6.0-24.0 13 3900 0.15 3120 0.6 13.9 142 4.54 69.53 6.82 2.4
2854 6.0-24.0 24 15200 0.46 13078 2.84 38.4 392 52.55 275 2805 17.49
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
15°
2-M3.0*0.5
DIRECTION OF ROTATION
CW/CCW
VENT HOLES
35.8±0.3
37±0.3
2-M3.0*0.5
35.8±0.3
28REF
0.5
10±0.1
0.5
13 +0
-0.10
6
2.5REF
50±0.5
A±0.3
Vent holes
Screw length 3.5max
4.8
50±0.3
A±0.3
28REF
VENT HOLES
SCREW LENGTH 3.5MAX
13 +0
-0.10
B±0.5
B±0.5
13 +0
-0.1
4.5
4.5
3.175 +0
-0.006
3.175 +0
-0.006
A
P
27.2REF
3.8±0.1
Hole
Red mark"+"
Vent holes
3.8±0.1
RED MARK"+"
VENT HOLES
STALL
Find even More at http://www.kinmoremotor.com Page [ 29 ]
HOLE
10
6.2REF
7.2REF
5REF

Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-550SA
RS-555SA
Customization:
1.Length A, B
2.Technical Data.
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Plastic End Cap
-Cordless Power Tool
-Class F Magnet Wire -EPB/Air Pump/Door Closer
-Leaf Brush System -Bilge Pump
-Carbon Steel Shaft -RC Model
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
23128R 6.0-24.0 24 4500 0.1 3932 0.39 25.7 262 10.6 204 2080 4.8
3.EMC/EMI Suppression
6034 6.0-12.0 12 16000 1.12 13613 4.96 25.6 261 40.36 281.4 2870 48.89
3540 6.0-12.0 12 7800 0.3 6708 1.84 21.9 223 15.35 156 1591 11.31
23100 6.0-24.0 24 7000 0.14 6004 0.77 19.2 196 12.09 124.5 1270 4.2
4.Optional Integrated or
Detached Structure for ETC
MODEL
25
RS-550/555A
DIRECTION OF ROTATION
CW/CCW
Vent holes
2-M3.0*0.5
0.15 P
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
RS-550/555H
Features: Typical Applications:
-Metal End Cap
-Class F Magnet Wire -RC Model
-Cordless Power Tool
-Leaf Brush System -Ride-on Car
-Carbon Steel Shaft -EPB/ETC/Air Pump/Door Closer
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RS-550SH 6529R 6.0-12.0 12 18000 1.25 15669 8.4 44.4 453 72.9 343 3499 56.5
RS-550PH 27130R 6.0-24.0 24 7500 0.2 6527 1.34 29.3 299 20 225.5 2300 9
RS-555SH 21100R 6.0-24.0 24 5300 0.13 4473 0.7 23.9 244 11.19 153 156.1 3.8
RS-555PH 2763R 6.0-24.0 24 7500 0.21 6460 1.3 32.6 333 22.09 235.5 2402 8.1
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
37±0.3
35.8±0.3
DIRECTION OF ROTATION
CW/CCW
25
VENT HOLES
2-M3.0*0.5
37.8±0.3
28REF
35.8±0.3
13 +0
-0.1
0.5
10±0.1
0.5
A±0.3
57±0.3
36REF
Screw length 3.5max
6
4.8
Vent holes
A±0.3
57±0.3
36REF
VENT HOLES
4.2REF
SCREW LENGTH 3.5MAX
13 +0
-0.1
B±0.5
B±0.5
13 +0
-0.1
4.5
3.175 +0
-0.006
4.5
3.175 +0
-0.006
A
P
3.8±0.1
Hole
Red mark"+"
27.2REF
VENT HOLES
Vent holes
STALL
3.8±0.1
HOLE
RED MARK"+"
Find even More at http://www.kinmoremotor.com Page [ 30 ]
10
6.5REF
4REF
7.3REF
7.4REF

Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Plastic End Cap
-Cordless Power Tool
-Class F Magnet Wire -EPB/Air Pump/Door Closer
-Leaf Brush System -Ride-on Car
-Carbon Steel Shaft -RC Model
MODEL OPERATING NOMINAL SPEED CURRENT SPEED CURREN TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A
T
mNm g.cm W mNm g.cm A
RS-560PA
22235
3783R R
6.0-24.0
6.0-12.0
12
6
1700
2450
0.07
0.19
1416
2051
0.35
0.98
18
17.9
184
183
2.68
3.85
108
110
1101.6
1122
1.74
5.01
Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-560A
DIRECTION OF ROTATION
CW/CCW
65°
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
25
25
VENT HOLES
Vent holes
RS-560/565H
Features: Typical Applications:
-Metal End Cap
-Cordless Power Tool
-Class F Magnet Wire -EPB/Air Pump/Door Closer
-Leaf Brush System -Ride-on Car
-Carbon Steel Shaft -RC Model
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURREN TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A
T
mNm g.cm W mNm g.cm A
RS-560SH 3775R 6.0-12.0 12 5800 0.27 5030 1.76 28.6 292 15.1 215.7 2200 11.5
RS-560PH 7021 6.0-12.0 12 25000 1.8 21803 12.27 47 479 107.38 368 3753.6 83.7
RS-565SH 22116R 6.0-12.0 12 4100 0.076 3560 0.5 24.5 250 9.16 186.3 1900 3.3
RS-565PH 2785R 6.0-15.0 13.5 3000 0.11 2632 0.52 19.6 200 5.4 147.1 1500 3.87
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
37.8±0.3
35.8±0.3
2-M3.0*0.5
0.15 P
DIRECTION OF ROTATION
CW/CCW
2-M3.0*0.5
37±0.3
35.8±0.3
2.0REF
28REF
15.6 +0
-0.1
0.5
10±0.1
0.5
6
4.8
A±0.3
60±0.5
A±0.3
60±0.3
36REF
VENT HOLES
36REF
Vent holes
Screw length 3.5max
13 +0
-0.1
13 +0
-0.1
SCREW LENGTH 3.5MAX
B±0.5
B±0.5
4.5
3.175 +0
-0.006
4.5
A
3.175 +0
-0.006
P
27.2REF
3.8±0.1
Red mark"+"
STALL
3.8±0.1
HOLE
RED MARK"+"
VENT HOLES
Hole
7.0REF
Find even More at http://www.kinmoremotor.com Page [ 31 ]
10
5.5REF
7.0REF
4.5REF

Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Metal End Cap
-Cordless Power Tools
-Class F Magnet Wire -Sewing Machine
-Leaf Brush System -Door Opener
-Carbon Steel Shaft -Vacuum Cleaner
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RS-590SH 3597R 6.0-12.0 12 5000 0.24 4000 1.94 37.3 380 15.6 186.3 1900 8.3
RS-590PH 7525R 6.0-12.0 12 16000 1.1 14366 9.67 53.8 548.8 80.9 526.6 5371 85
RS-595SH 2862R 6.0-24.0 24 6600 0.18 5784 1.27 38.5 393 23.32 311.8 3180 9
RS-595PH 23113R 6.0-24.0 24 3650 0.07 3233 0.54 23.2 236.6 7.85 203 2070 4.2
RS-595VH 7523R 6.0-12.0 12 18500 1.25 16310 9.31 48.5 494.7 82.92 410 4182 69.3
Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
25
DIRECTION OF ROTATION
CW/CCW
RS-590/595H
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
25
VENT HOLES
RS-520SH
Features: Typical Applications:
-Metal End Cap -Dispenser
-Class F Magnet Wire -RC Model
-Leaf Brush System -Robot
-Carbon Steel Shaft -Toy
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RS-520SH 14230 3.0-6.0 5 2000 0.18 1350 0.38 3.6 36.72 0.5 10.98 112 0.78
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
35.8±0.3
0.5
10±0.1
2-M3.0*0.5
0.15 P
DIRECTION OF ROTATION
CW/CCW
2-M3.0*0.5
0.15 P
6
4.8
A±0.3
67±0.3
VENT HOLES
13 +0
-0.1
SCREW LENGTH 3.5MAX
B±0.5
3.5REF 32.5±0.5 B±0.5
35.8±0.3
28REF
13 +0
-0.1
0.5
A±0.3
Screw length 3.5 max
13 +0
-0.1
4.5
3.175 +0
-0.005
4.5
3.175 +0
-0.006
P
P
27.2REF
3.8±0.1
HOLE
RED MARK"+"
10
STALL
3.8±0.1
Find even More at http://www.kinmoremotor.com Page [ 32 ]
6
6.5REF
7.3REF
25.8REF

Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-750SH
RS-755SH
Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Metal End Cap
-Class F Magnet Wire
-Cordless Power Tool
-Leaf Brush System -Door Opener
-Carbon Steel Shaft -EPB
-Air Pump/Vacuum Cleaner
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
7032R 6.0-12.0 12 15000 1.79 12671 7.52 48.6 496 66.6 393.1 4010 55.6
29195R 6.0-24.0 24 5000 0.19 4470 0.79 34.1 348 15.48 223.5 2280 9.72
4.EMC/EMI Suppression
MODEL
RS-770SH
29
RS-750/755H
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
7512R 3.0-6.0 6 9500 2.26 8123 9.31 45.1 460 38.2 306.9 3130 66.34
27115 6.0-24.0 24 4260 0.18 3614 1.01 43 439 16.27 283.5 2892 5.64
29
DIRECTION OF ROTATION
CW/CCW
Vent holes
2-M4.0*0.7
RS-770/775H
Features: Typical Applications:
-Metal End Cap
DIRECTION OF ROTATION
CW/CCW
-Class F Magnet Wire
-Cordless Power Tool
-Air Pump/Vacuum Cleaner
-Leaf Brush System -RC Model/Boat
-Carbon Steel Shaft -EPB
VENT HOLES
2-M4.0*0.7
0.15 P
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
8523R 6.0-12.0 12 15000 2.2 13177 15.91 81 826 111.8 666.9 6802 115
29195R 6.0-24.0 24 5000 0.19 4470 0.79 34.1 348 15.48 223.5 2280 9.72
RS-775SH 25110R 6.0-24.0 24 3478 0.15 2925 0.75 44.4 453 13.35 245.7 2506 4.07
RS-775PH 5028R 6.0-12.0 12 6800 0.53 5844 3.24 44.1 450 27 313.8 3200 19.8
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
45±0.3
41.8±0.3
6.5REF
43.8±0.3
41.8±0.3
33REF
17.4±0.1
33.2REF
0.6
6.5REF
17.4 +0
-0.1
0.6
Vent holes
VENT HOLES
A±0.3
59±0.3
29REF
7.0REF
Screw length 3.5max
A
66±0.3
38REF
5REF
SCREW LENGTH 3.5 MAX
B±0.5
17.5 +0
-0.1
B
17.5 +0
-0.1
5 +0
-0.005
P
4.5±0.1
29
5 +0
-0.005
P
4.5±0.1
Red mark"+"
RED MARK"+"
29
4.6
Hole
14.6
Vent holes
STALL
4.6
HOLE
14.8
VENT HOLES
Find even More at http://www.kinmoremotor.com Page [ 33 ]
7REF
3.5REF
7.3REF
5REF

Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-790SH
RS-795SH
Customization:
1.Length A, B
2.Technical Data
3.Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-850SA
29
Your Reliable DC and Gear Motor Supplier
DIRECTION OF ROTATION
CW/CCW
RS-790/795H
Features: Typical Applications:
-Metal End Cap
-Class F Magnet Wire
-Cordless Power Tool
-Leaf Brush System -Door Opener
-Carbon Steel Shaft -EPB
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
-Air Pump/Vacuum Cleaner
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
4577R 6.0-12.0 12 4200 0.35 3609 2.13 49.7 507 18.77 352.9 3600 13
8018R 6.0-12.0 12 17500 2.2 15287 15.2 86.8 885 139 686.3 7000 105
5533R 6.0-12.0 12 5250 0.33 4742 3.08 54.5 556 27.05 563.2 5745 28.8
4739R 6.0-24.0 24 8800 0.38 7774 2.88 63.8 651 51.93 547 5579 21.81
30
6.5REF
43.8±0.3
41.8±0.3
33REF
17.4±0.1
2-M4*0.7
0.15 A
RS-850A
Features: Typical Applications:
-Plastic End Cap
-Cordless Power Tool
-Class F Magnet Wire -Lean Product
-Leaf Brush System -RC Model/Boat
-3 Slots Armature/3 Bars Commutator
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
23160R 6.0-12.0 12 2750 0.13 2289 0.65 23 235 5.52 137.3 1400 3.2
27190R 6.0-12.0 12 2250 0.11 1893 0.58 24.9 254 4.93 156.9 1600 3.1
23245R 6.0-12.0 24 3300 0.1 2838 0.59 29.8 304 8.9 212.8 2170 3.6
29146R 6.0-24.0 24 6135 0.19 5406 1.05 38.3 391 21.75 323.5 3300 10.13
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
0.6
DIRECTION OF ROTATION
CW/CCW
3-M3.0*0.5
0.15 P
46.2±0.3
45±0.3
Vent holes
28REF
0.5
A±0.3
75±0.3
38REF
Screw length 3.5MAX
A±0.3
55±0.3
36REF
4.5
15 +0
-0.10
4.5
Screw length 3.5max
B±0.5
17.5 +0
-0.1
5 +0
-0.005
A
4 +0
-0.005
29
P
Red"+"
4.6
3.8±0.1
Hole
White mark"+"
14.6
STALL
33REF
Vent holes
Find even More at http://www.kinmoremotor.com Page [ 34 ]
B±0.5
6.5REF
7.5REF
4.5REF
5.8REF

Customization:
1.Length A, B
2.Technical Data
3.EMC/EMI Suppression
MODEL
RS-987SH
Customization:
1.Length A, B
2.Technical Data
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-Carbon Steel Shaft
-Cordless Power Tool
-Class F Magnet Wire -Bilge Pump
-Leaf Brush System -Door Opener
-7 Slots Armature/7 Bars Commutator -RC Model/Boat
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
25115 12.0-24.0 24 2200 0.19 1804 0.65 55.6 567 10.03 227 2310 2.7
3.EMC/EMI Suppression
MODEL
RS-997SH
32
RS-987H
DIRECTION OF ROTATION
CW/CCW
4-M5.0*0.8
0.15 P
VOLTAGE NO LOAD
5524 12.0-24.0 24 11000 1.24 9499 7.87 102.9 1050 97.8 746 7700 50.1
3755 12.0-32.0 24 6300 0.5 5441 2.85 87.1 888 47.34 57.9 5910 16.2
RS-997H
Features: Typical Applications:
-Carbon Steel Shaft
-Cordless Power Tool
-Class F Magnet Wire -Bilge Pump
-Leaf Brush System
Vent holes
-Air Pump/Vacuum Cleaner
-7 Slots Armature/7 Bars Commutator -RC Model/Boat
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
7009 6.0-12.0 12 9800 1.95 8808 17.32 169.7 1713 154.9 1660 16930 153.8
8508 6.0-14.0 14 13000 2.5 11160 15.17 124.9 1274 145.9 882 9000 92
5527 6.0-24.0 24 6500 0.7 5639 4.58 133.9 1366 79.05 1010 10302 30
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
90°
Vent holes
51.8±0.5
DIRECTION OF ROTATION
CW/CCW
4-M5.0*0.8
0.15 P
32
90°
51.8±0.5
41.8REF
21±0.1
Vent holes
41.8REF
21 0
-0.1
0.6
0.6
A±0.3
69±0.3
21.7 0
-0.1
Screw length 5.5MAX
B±0.5
AT MAXIMUM EFFICIENCY
3.0REF
A±0.3
85±0.3
Vent holes
Screw length 5.5max
21.7 +0
-0.1
B±0.5
5.5
5.5
6.35 -0.007
-0.012
6.35 +0
-0.005
P
37.6
Vent holes
P
4.8±0.1
Hole
Red mark"+"
Hole
Red mark"+"
37.6
4.8±0.1
14.7
STALL
14.6
STALL
Find even More at http://www.kinmoremotor.com Page [ 35 ]
8REF
7.5REF

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
FS-5516SH
Customization:
1.Length A, B
2.Technical Data
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-DMD Insulation
-Rotary Tool
-Cage Brush System -Power Brush
-Metal End Cap -Mixer
-8 Slots Armature/16 Bars Commutator -Hair Clipper
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
08364R AC Rect. 230 11200 0.12 7297 0.39 45.33 462.4 33.88 123.2 1257 0.98
08400R AC Rect. 220 10100 0.06 6628 0.28 37.52 382.7 25.33 91.93 938 0.66
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
Features: Typical Applications:
-DMD Insulation
-Cage Brush System
-Power Brush
-Coffee Machine
-Metal End Cap -Meat Grinder
-8 Slots Armature/16 Bars Commutator -Hair Clipper
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RS-5416SA 10252 AC Rect. 120 15123 0.1 11664 0.34 18.13 184.9 21.22 99.4 1014 1.46
RS-5416PA
FS-5516H
DIRECTION OF ROTATION
CW/CCW
28
VENT HOLES
37.8±0.3
2-M3.0*0.5
VENT HOLES
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
RS-5416A
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
08386 AC Rect. 110 6600 0.02 5478 0.1 13 132.6 7.12 76 775.2 0.5
08400 AC Rect. 220 13000 0.03 11056 0.16 22 224.4 24.32 147 1499 0.9
11210 AC Rect. 110 12100 0.05 10313 0.29 21 214.2 21.66 142 1448 1.7
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
35.8±0.3
DIRECTION OF ROTATION
65°
25
CW/CCW
Vent holes
37±0.3
35.8±0.3
2-M3.0*0.5
0.15 P
2.0REF
28REF
0.5
A±0.3
63±0.3
38REF
11.1 +0
-0.1
2.8±0.1
5.0REF 4.0
SCREW LENGTH 3.5MAX 11.1 +0
15.6 +0
-0.1
A ±0.3
50±0.5
28REF
Vent holes
4.6REF
Screw length 3.5max
B
B±0.5
13 +0
-0.1
4 +0
-0.005
P
4.5
26
3.175 +0
-0.006
P
-0.1
4.5REF
31.5±0.3
3.8±0.1
29±0.3
Hole
Red mark"+"
STALL
Find even More at http://www.kinmoremotor.com Page [ 36 ]
0.5
8.5REF
RED MARK"+"
5.5REF
4.3REF

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-5516SA
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-DMD Insulation
-Cage Brush System
-Plastic End Cap -Mixer
-Sewing Machine
-Coffee Machine
-8 Slots Armature/16 Bars Commutator -Hair Clipper
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
09306 AC Rect. 230 14300 0.05 11951 0.25 29 295.8 34.66 177 1805 1.25
13162 AC Rect. 120 14100 0.09 11927 0.49 34 346.8 40.55 221 2254 2.72
10230 AC Rect. 230 21000 0.09 17328 0.42 44.6 455 80.91 254.9 2600 2
RS-5516PA 09310 AC Rect. 230 11500 0.04 9735 0.23 33 336.6 33.64 215 2193 1.29
Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-5516A
DIRECTION OF ROTATION
CW/CCW
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
RS-5616A
DIRECTION OF ROTATION
CW/CCW
65°
65°
25
25
Vent holes
Features: Typical Applications:
-DMD Insulation
-Cage Brush System
-Power Brush
-Coffee Machine
-Plastic End Cap -Mixer/Blender
-8 Slots Armature/16 Bars Commutator -Hair Clipper
Vent holes
2-M3.0*0.5
0.15 P
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RS-5616SA 09254 AC Rect. 230 18000 0.09 14440 0.35 38.76 395.4 58.65 196 2000 1.4
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
37.8±0.3
37.8±0.3
35.8±0.3
2-M3.0*0.5
0.15 P
35.8±0.3
2.0REF
28REF
2.0REF
28REF
15.6 +0
-0.1
0.5
15.6 +0
-0.1
0.5
A±0.3
57±0.5
36REF
Vent holes
Screw length 3.5max
A±0.3
60±0.5
13 +0
-0.1
36REF
Vent holes
Screw length 3.5max
13 +0
-0.1
B±0.5
4.5
B±0.5
3.175 +0
-0.006
4.5
P
3.175 +0
-0.006
Red mark"+"
P
3.8±0.1
Hole
3.8±0.1
Red mark"+"
STALL
Hole
7.0REF
Find even More at http://www.kinmoremotor.com Page [ 37 ]
5.5REF
7.0REF
5.5REF

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-5916SA
Customization:
1.Length A, B
2.Technical Data
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-DMD Insulation
-Cage Brush System
-Coffee Machine
-Power Brush
-Plastic End Cap -Hand Blender
-8 Slots Armature/16 Bars Commutator -Hair Clipper
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
09326R AC Rect. 230 9600 0.18 8308 0.18 33 336.6 27.42 245 2499 1.14
12170R AC Rect. 123.5 9600 0.06 8125 0.34 36 367.2 29.25 234 2387 1.9
15118R AC Rect. 120 12800 0.1 11118 0.66 49 499.8 57.05 373 3805 4.32
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-7512SH
RS-5916A
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
29
DIRECTION OF ROTATION
CW/CCW
65°
25
VENT HOLES
2-M3.0*0.5
37.8±0.3
35.8±0.3
0.15 P
RS-7512H
DIRECTION OF ROTATION
CW/CCW
VENT HOLES
Features: Typical Applications:
-DMD Insulation -Coffee Grinder
-Cage Brush System -Hedge Trimmer
-Metal End Cap -Stick Blender
-12 Slots Armature/24 Bars Commutator -Juicer/Mixer
2-M4.0*0.7
0.15 A
2.0REF
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
13162 AC Rect. 230 17700 0.12 14846 0.62 68 693.6 100.95 422 4304 3.2
09266 AC Rect. 120 9100 0.06 7280 0.25 47 479.4 35.83 235 2379 1.02
10200 AC Rect. 230 12500 0.07 10364 0.34 47 479 51.01 275 2805 1.65
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
28REF
43.8±0.3
41.8±0.3
15.6 +0
-0.1
0.5
0.6
33REF
17.4±0.1
VENT HOLES
A±0.3
67±0.5
36REF
VENT HOLES
10.2REF
SCREW LENGTH 3.5MAX
A±0.3
59±0.3
30REF
4.5±0.1
SCREW LENGTH 3.5MAX
17.5 +0
-0.1
B±0.5
B±0.5
13 +0
-0.1
3.175 +0
-0.006
4.5±0.1
5 +0
-0.005
2.5±0.5
3.8±0.1
HOLE
RED MARK"+"
4.8±0.1
HOLE
4.5REF
STALL
RED MARK"+"
14.8
VENT HOLES
Find even More at http://www.kinmoremotor.com Page [ 38 ]
29
7REF
5.4REF
4.0REF

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-7712SH
Customization:
1.Length A, B
2.Technical Data
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-DMD Insulation -Coffee Grinder
-Cage Brush System -Hedge Trimmer
-Metal End Cap -Hand Blender
-12 Slots Armature/24 Bars Commutator -Juicer/Mixer
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
12182R AC Rect. 230 8500 0.04 7471 0.3 57 581.4 42.58 471 4804 2.2
15124R AC Rect. 230 14500 0.08 12676 0.55 74 754.8 93.8 588 6000 3.8
12166R AC Rect. 230 9450 0.06 8165 0.39 70 714 59.85 515 525.3 2.49
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-7912SH
29
RS-7712H
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
12190 AC Rect. 240 12200 0.06 10458 0.36 56 571.2 58.56 392 4000 2.15
29
DIRECTION OF ROTATION
CW/CCW
VENT HOLES
RS-7912H
6.5REF
Features: Typical Applications:
-DMD Insulation
-Cage Brush System
-Metal End Cap
-Coffee Machine
-Power Tool
-Stick Blender
-12 Slots Armature/24 Bars Commutator -Juicer/Mixer
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
15102R AC Rect. 220 15000 0.07 13341 0.57 72 734.4 96.06 651 6640 4.6
09290 AC Rect. 230 5500 0.03 4612 0.15 46 469.2 22.22 285 2907 0.78
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
45±0.3
2-M4.0*0.7
0.15 P 0.5
DIRECTION OF ROTATION
CW/CCW
Vent holes
45±0.3
41.8±0.3
41.8±0.3
2-M4*0.7
0.15 P
33REF
17.4±0.1
6.5REF
33REF
17.4±0.1
0.5
A±0.3
66±0.3
VENT HOLES
38REF
SCREW LENGTH3.5MAX
Vent holes
A±0.3
75±0.3
17.5 +0
-0.1
38REF
17.5 +0
-0.1
Screw length 3.5max
B±0.5
5 +0
-0.005
4.5±0.1
B±0.5
14.8
RED MARK"+"
P
4.5±0.1
29REF
29
4.8
HOLE
VENT HOLES
4.8
STALL
Hole
Red mark"+"
Find even More at http://www.kinmoremotor.com Page [ 39 ]
5 +0
-0.005
14.6
7REF
4.0REF
5.7REF
5.3REF

Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
Your Reliable DC and Gear Motor Supplier
Features: Typical Applications:
-DMD Insulation
-Coffee Machine
-Cage Brush System -Power Tool
-Metal End Cap -Blender
-12 Slots Armature/24 Bars Commutator
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
-Mixer
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
RS-9812SH 17122 AC Rect. 110 7545 0.41 5624 1.04 97.92 998.8 56.69 424.2 4327 3.7
RS-9812PH 12266 AC Rect. 230 7883 0.16 5281 0.52 109.4 1115 59.85 430.2 4388 1.72
Customization:
1.Length A, B
2.Technical Data
3.Flux Ring&Cooling Fan
4.EMC/EMI Suppression
MODEL
RS-9912SH
32
32
RS-9812H
DIRECTION OF ROTATION
CW/CCW
VENT HOLES
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY
DIRECTION OF ROTATION
CW/CCW
Vent holes
4-M3.0*0.5
RS-9912H
Features: Typical Applications:
-DMD Insulation
-Coffee Machine
-Cage Brush System -Power Tool
-Metal End Cap -Blender
-12 Slots Armature/24 Bars Commutator
90°
51.8±0.5
0.15 P
OPERATING NOMINAL SPEED CURRENT SPEED CURRENT TORQUE OUTPUT TORQUE CURRENT
-Mixer
VOLTAGE NO LOAD AT MAXIMUM EFFICIENCY STALL
RANGE V r/min A r/min A mNm g.cm W mNm g.cm A
1794 AC Rect. 220 14000 0.35 10651 1.25 2041 227.5 65.01 4.5 9411 90
2072 AC Rect. 100 8000 0.35 6256 1.26 1417 92.8 58 4.8 6813 72
15106 AC Rect. 220 11500 0.3 9000 1 1910 179.8 64.2 3.52 8786 27.2
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
90°
4-M5.0*0.8
0.15 P
51.8±0.5
41.8REF
41.8REF
0.5
21 +0
-0.1
7.6
21 0
-0.1
0.6
VENT HOLES
69±0.3
A±0.3
VENT HOLES
21.7 0
-0.1
SCREW LENGTH5.5MAX
A±0.3
85±0.3
Vent holes
21.7 +0
-0.1
Screw length 5.5max
B±0.5
B±0.5
5.5
6.35 +0
-0.005
37.6
VENT HOLES
5.5
P
4.8±0.1
HOLE
RED MARK"+"
Red mark"+"
37.6REF
14.7
4.8±0.1
STALL
Find even More at http://www.kinmoremotor.com Page [ 40 ]
6.35 +0
-0.005
Hole
14.7
7.0REF
7.0REF

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Coffee Machine
-Metal or Carbon Brush DC Motor -Cordless Drill
-Spur Gears -Robot
-Copperplate Gear Case -Electric Lock
-Sleeve Bronze Bushing -Video/Camera
1/30 1/50 1/63 1/70 1/100
1/210 1/380 - - -
- - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/30 KM-12FN20-30-12480 3.0-12.0 12.0 0.03 480 0.11 0.060 340
1/50 KM-12FN20-50-03350 1.5-3.0 3.0 0.1 350 0.32 0.075 300
1/63 KM-12FN20-63-12254 3.0-12.0 12.0 0.02 254 0.07 0.063 218
1/100 KM-12FN20-100-06240 3.0-6.0 6.0 0.06 240 0.14 0.1 225
1/150 KM-12FN20-150-12128 3.0-12.0 12.0 0.02 128 0.11 0.4 80
1/298 KM-12FN20-298-0340 1.5-3.0 3.0 0.04 40 0.20 0.59 29.5
1/380 KM-12FN20-380-0335 1.5-3.0 3.0 0.04 35 0.20 0.55 29
Remarks:
9.1
11
8.0REF
Ratio Model No.
1. All values approximate.
Positive Pole
1/10
Your Reliable DC and Gear Motor Supplier
1/1000 -
KM-12FN20
1/20
1/110 1/150
Operating
Range
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
4.0±0.1
3.0±0.05
V
2.5±0.1
A ±0.5
B ±0.1
Voltage
0.7
L ±0.2
15.1
General Reduction Ratios
10.0±0.2
No Load On Load
5.0
12.0
DIRECTION OF ROTATION
CW/CCW
2-M1.6X0.35
SCREW LENGTH
MAX 0.8mm
Find even More at http://www.kinmoremotor.com Page [ 41 ]
9.0
12.0±0.2

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
KM-12FN30
Features: Typical Applications:
-Bi-direction -Coffee Machine
-Metal or Carbon Brush DC Motor -Cordless Drill
-Spur Gears -Robot
-Copperplate Gear Case -Electric Lock
-Sleeve Bronze Bushing -Video/Camera
1/10 1/20 1/30 1/50 1/63 1/70 1/100
1/110 1/150 1/210 1/380 - - -
11 1/1000 - - - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V V A r/min A kg.cm r/min
1/50 KM-12FN30-50-02.5100 2.0-3.0 2.5 0.04 100 0.14 0.054 80
1/210 KM-12FN30-210-1270 6.0-12.0 12.0 0.02 71 0.07 0.43 61
1/298 KM-12FN30-298-1250 6.0-12.0 12.0 0.02 50 0.07 0.6 43
1/298 KM-12FN30-298-0848 6.0-8.0 8.0 0.04 48 0.21 1.5 28
Remarks:
9.1
8.0REF
Positive Pole
Ratio Model No.
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
4.0±0.1
3.0±0.05
Operating
Range
General Reduction Ratios
Voltage No Load On Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
2.5±0.1
A ±0.5
B ±0.1
0.7
L ±0.2
20.1
5.0
12.0
DIRECTION OF ROTATION
CW/CCW
10.0±0.2
2-M1.6X0.35
SCREW LENGTH
MAX 0.8mm
Find even More at http://www.kinmoremotor.com Page [ 42 ]
9.0
12.0±0.2

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
KM-13F030
Features: Typical Applications:
-Bi-direction -Coffee Machine
-Metal Brush DC Motor -Cordless Drill
-Spur Gears -Robot
-Copperplate Gear Case -Electric Lock
-Sleeve Bronze Bushing -Video/Camera
1/3 1/10 1/17 1/20 1/30 1/35 1/50
1/63 1/86 1/115 1/150 1/250 1/360 -
Nominal
Voltage
Current Speed Current 0.054 Speed
V V A r/min A kg.cm r/min
1/35 KM-13F030-35-03485 2.0-4.0 3.0 0.15 485 0.47 0.082 415
1/150 KM-13F030-150-03118 2.0-4.0 3.0 0.15 118 0.47 0.35 95
Remarks:
11
Ratio Model No.
1. All values approximate.
Positive Pole
Your Reliable DC and Gear Motor Supplier
12REF
9.3REF
Operating
Range
General Reduction Ratios
Voltage No Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
3 ±0.05
2.5 ±0.1
A ±0.5
B ±0.1
11
18.6REF
5
15.5
2-M2.0
SCREW LENGTH
MAX 0.8mm
CW
9
12±0.2
On Load
Find even More at http://www.kinmoremotor.com Page [ 43 ]
13±0.2

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Coffee Machine
-Metal or Carbon Brush DC Motor -Cordless Drill
-Spur Gears -Robot
-Copperplate Gear Case -Electric Lock
-Sleeve Bronze Bushing -Video/Camera
1/3 1/10 1/17 1/20 1/30 1/35 1/50
1/63 1/86 1/115 1/150 1/250 1/360 -
Nominal
Voltage
Current Speed Current 0.054 Speed
V A r/min A kg.cm r/min
1/30 KM-13F030-30-07550 3.0-8.0 7.0 0.1 550 0.31 0.04 451.1
1/150 KM-13F030-150-07100 3.0-8.0 7.0 0.1 100 0.31 0.2 90
Remarks:
11
Ratio Model No.
1. All values approximate.
Positive Pole
12REF
Your Reliable DC and Gear Motor Supplier
KM-13F050
9.3REF
Operating
Range
General Reduction Ratios
Voltage No Load On Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
3 ±0.05
2.5 ±0.1
V
A ±0.5
B ±0.1
11
26.9REF
5
15.5
2-M2.0
SCREW LENGTH
MAX 0.8mm
CW
9
12±0.2
Find even More at http://www.kinmoremotor.com Page [ 44 ]
13±0.2

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Electric Lock
-Metal Brush DC Motor -Robot
-Spur Gears -Actuator
-Copperplate Gear Case -Armarium
-Sleeve Bronze Bushing
1/16 - - - - -
1/32 1/37 1/45 - - -
1/65 1/75 1/91 1/100 1/105 1/128
1/182 1/210 1/256 1/283 1/296 1/362
1/592 1/631 1/723 1/835 1/1012 -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/13 KM-16A030-13-121330 6.0-12.0 12.0 0.046 1332 0.094 0.03 1171
1/128 KM-16A030-128-0659 4.0-8.0 6.0 0.015 60 0.06 0.3 40.8
1/298 KM-16A030-296-0521 4.0-6.0 5.0 0.03 21.1 0.8 0.5 16
1/631 KM-16A030-631-0625 4.0-8.0 6.0 0.07 25.2 0.23 2.5 20
1/835 KM-16A030-835-0507 4.0-6.0 5.0 0.023 6.8 0.04 0.5 5.8
Remarks:
11
12.5
14
15.5
17
Ratio Model No.
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
Positive Pole
12.0 REF
Number Of
Stage
KM-16A030
3 1/13
4 1/26
5 1/53
6
7
1/148
1/448
Operating
Range
Voltage
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
3 -0.01
-0.03
V
2.5 +0
-.01
2.8
A ±0.5
C ±0.1
7
B ±0.2
18.6REF
(+)
15.5REF
10 ±0.1
2-M2
MAX Depth 2.0mm
No Load On Load
DIRECTION OF ROTATION
CW/CCW
Find even More at http://www.kinmoremotor.com Page [ 45 ]
16

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Electric Lock
-Metal or Carbon Brush DC Motor -Robot
-Spur Gears -Actuator
-Copperplate Gear Case -Armarium
-Sleeve Bronze Bushing
1/16 - - - - -
1/32 1/37 1/45 - - -
1/65 1/75 1/91 1/100 1/105 1/128
1/182 1/210 1/256 1/283 1/296 1/362
1/592 1/631 1/723 1/835 1/1012 -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/13 KM-16A050-13-241100 6.0-24.0 24.0 0.022 1088 0.088 0.08 844
1/91 KM-16A050-91-3.5110 1.5-4.0 3.5 0.07 111.4 0.3 0.5 88
1/105 KM-16A050-105-1.590 1.0-2.0 1.5 0.22 90 0.65 0.5 65.6
1/256 KM-16A050-256-1234 6.0-12.0 12.0 0.022 33.3 0.045 0.5 30.6
1/448 KM-16A050-448-3.520.2 1.5-4.0 3.6 0.07 20 0.25 2 15.3
Remarks:
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
17 7 1/448
Ratio Model No.
Positive Pole
12.0 REF
11 3 1/13
12.5 4 1/26
14 5 1/53
15.5 6 1/148
KM-16A050
3 -0.01
-0.03
Operating
Range
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
Voltage
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2.5 +0
-.01
2.8
A ±0.5
B ±0.1
7
L ±0.2
26.9REF
(+)
15.5REF
2-M2
MAX Depth 2.0mm
10±0.1
No Load On Load
DIRECTION OF ROTATION
CW/CCW
Find even More at http://www.kinmoremotor.com Page [ 46 ]
16

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush DC Motor -Business Machine
-Spur Gears -Duplicating Machine
-Copperplate Gear Case -Pump
-Sleeve Bronze Bushing
1/12.5 1/16 1/23 1/28 1/35 1/39
1/63.5 1/70 1/78 1/98 - -
1/107 1/144 1/175.7 1/195 1/244 -
1/359 1/440 1/469 1/488 1/545 1/610
1/899 1/1099 1/1200 1/1361 1/1526 -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/23 KM-20A130R-23-12600 6.0-12.0 12.0 0.057 591.7 0.22 0.2 491
1/107 KM-20A130R-107-0636 4.0-8.0 6.0 0.03 35.6 0.082 0.6 26.3
1/144 KM-20A130R-144-1.513 1.5-3.0 1.5 0.02 13.2 0.054 0.2 10
1/195 KM-20A130R-195-0640 4.8-8.0 6.0 0.07 40 0.17 1.4 32
1/488 KM-20A130R-488-0616 4.0-8.0 6.0 0.09 16 0.17 3.0 12
Remarks:
17.7 5 1/43
19.2 6 1/103
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
16.2 3-4 1/6.6
20.7 7 1/269
22.2 8 1/644
Ratio Model No.
Positive Pole
4 -0.01
-0.03
KM-20A130R
3.5 -0
-0.1
Operating
Range
General Reduction Ratios
Voltage No Load On Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
A ±0.5
B ±0.1
3
L ±0.2
7
22.8REF
(+)
17REF
DIRECTION OF ROTATION
CW/CCW
20
15 ±0.1
2-M2.5
Max Depth 4.5mm
Find even More at http://www.kinmoremotor.com Page [ 47 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal or Carbon Brush DC Motor -Business Machine
-Spur Gears -Duplicating Machine
-Copperplate Gear Case -Pump
-Sleeve Bronze Bushing
1/12.5 1/16 1/23 1/28 1/35 1/39
1/63.5 1/70 1/78 1/98 - -
1/107 1/144 1/175.7 1/195 1/244 -
1/359 1/440 1/469 1/488 1/545 1/610
1/899 1/1099 1/1200 1/1361 1/1526 -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/23 KM-20A130F-23-12600 6.0-12.0 12.0 0.15 6.0 0.37 0.3 501
1/44 KM-20A130F-144-1243 6.0-12.0 12.0 0.05 41.6 0.12 1.4 29
1/258 KM-20A130F-258-07.1910 6.0-8.0 7.19 0.03 9.8 0.04 0.6 8.1
1/469 KM-20A130F-469-2425.5 6.0-24.0 24.0 0.04 25 0.12 3 21.3
1/1220 KM-20A130F-1221-1205 6.0-12.0 12.0 0.03 5.1 0.06 4 4
Remarks:
15REF
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
16.2 3-4 1/6.6
17.7 5 1/43
19.2 6 1/103
20.7 7 1/269
22.2 8 1/644
Ratio Model No.
Positive Pole
7
4 -0.01
-0.03
KM-20A130F
3.5 -0
-0.1
Operating
Range
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
Voltage
32.1REF
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
B ±0.1
A ±0.5
3
L ±0.2
DIRECTION OF ROTATION
CW/CCW
No Load On Load
(+)
20.4REF
20
15 ±0.1
2-M2.5
Max Depth 4.5mm
Find even More at http://www.kinmoremotor.com Page [ 48 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal or Carbon Brush DC Motor -Business Machine
-Spur Gears -Duplicating Machine
-Copperplate Gear Case -Pump
-Sleeve Bronze Bushing
1/12.5 1/16 1/23 1/28 1/35 1/39
1/63.5 1/70 1/78 1/98 - -
1/107 1/144 1/175.7 1/195 1/244 -
1/359 1/440 1/469 1/488 1/545 1/610
1/899 1/1099 1/1200 1/1361 1/1526 -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/16 KM-20A180-16-241400 6.0-24.0 24.0 0.148 1334 0.746 0.6 1090
1/58 KM-20A180-58-03125 2.0-3.0 3.0 0.22 121.4 0.75 0.6 97.6
1/78 KM-20A180-78-1243 6.0-12.0 12.0 0.02 43 0.045 0.5 34.5
1/144 KM-20A180-144-1585 6.0-15.0 15.0 0.08 84.6 0.474 3 60.7
1/1220 KM-20A180-1220-1205 6.0-12.0 12.0 0.032 5.1 0.057 4 4.6
Remarks:
1. All values approximate.
15REF
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
16.2 3-4 1/6.6
17.7 5 1/43
19.2 6 1/103
20.7 7 1/269
22.2 8 1/644
Ratio Model No.
Positive Pole
7
4 -0.01
-0.03
KM-20A180
3.5 -0
-0.1
Operating
Range
General Reduction Ratios
Voltage No Load On Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
B ±0.1
A ±0.5
3
L ±0.2
32.1REF
(+)
20.4REF
20
15 ±0.1
2-M2.5
Max Depth 4.5mm
Find even More at http://www.kinmoremotor.com Page [ 49 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal or Carbon Brush DC Motor -Garden Tool
-Spur Gears -Electric Lock
-Copperplate Gear Case -Actuator
-Sleeve Bronze Bushing
1/15 1/20 - - - -
1/26 1/34 1/42.8 1/45 - -
1/75 1/98 - - - -
1/165 1/217 - - -
1/362 1/478 - - -
1/796 1/1051 - - -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/75 KM-25A310-75-1295 6.0-12.0 12.0 0.03 95 0.06 0.22 84.1
1/98 KM-25A310-98-01.510 1.5-2.0 1.5 0.02 9.5 0.03 0.04 8
1/217 KM-25A320-217-1325 6.0-13.0 13.0 0.02 25.3 0.05 0.8 22
1/274 KM-25A320-274-1312.8 6.0-13.0 13.0 0.01 12.8 0.03 0.8 11
1/478 KM-25A320-478-1208 6.0-12.0 12.0 0.03 7.3 0.05 1.8 6.4
Remarks:
4 -0.01
-0.03
3.5 -0
-0.1
21 5 1/10.6
23 6 1/57
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
19 4 1/11
25 7 1/125
27 8 1/274
29 9 1/603
Ratio Model No.
A ±0.5
B ±0.1
2.5
KM-25A310/320
9
Operating
Range
Voltage
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
L ±0.2
18.4REF
24.4REF
25
4-M3
MAX Depth 5mm
DIRECTION OF ROTATION
CW/CCW
17 ±0.1
35°
20 ±0.1
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 50 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal or Carbon Brush DC Motor -Garden Tool
-Spur Gears -Electric Lock
-Copperplate Gear Case -Actuator
-Sleeve Bronze Bushing
1/15 1/20 - - - -
1/26 1/34 1/42.8 1/45 - -
1/75 1/98 - - - -
1/165 1/217 - - -
1/362 1/478 - - -
1/796 1/1051 - - -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/11 KM-25A370-11-241400 6.0-24.0 24.0 0.09 1415 0.35 0.6 1057
1/125 KM-25A370-125-1280 6.0-12.0 12.0 0.21 80.2 0.87 4.5 58
1/274 KM-25A370-274-4.560 3.0-5.0 4.5 0.75 62.8 3.3 7.6 49.4
1/362 KM-25A370-362-1242 6.0-12.0 12.0 0.16 42.3 0.83 8 34
1/478 KM-25A370-487-1220 6.0-12.0 12.0 0.08 21 0.57 9 16.4
Remarks:
4 -0.01
-0.03
3.5 -0
-0.1
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
19 4 1/11
21 5 1/10.6
23 6 1/57
25 7 1/125
27 8 1/274
29 9 1/603
Ratio Model No.
A ±0.5
B ±0.1
2.5
KM-25A370
9
Operating
Range
General Reduction Ratios
Voltage No Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
L ±0.2
30.8REF
24.4REF
25
4-M3
MAX Depth 5mm
DIRECTION OF ROTATION
CW/CCW
17 ±0.1
35°
20 ±0.1
On Load
Find even More at http://www.kinmoremotor.com Page [ 51 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -ATM/Robot
-Spur Gears -Toy
-Copperplate Gear Case -Cleaning Brush
-Sleeve Bronze Bushing
1/8.2 1/14.5 1/15 1/18.6 - -
1/42.3 - - - - -
1/96.3 - - - - -
1/219 - - - - -
1/497 - - - - -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/18.6 KM-28A360-18.6-12338 6.0-12.0 12.0 0.13 338 0.32 0.62 270
1/42.3 KM-28A360-42.3-1284 6.0-12.0 12.0 0.12 150 0.34 1.3 119
1/170 KM-28A360-170-1237 6.0-12.0 12.0 0.1 37 0.36 5 29
1/219 KM-28A360-219-1229 6.0-12.0 12.0 0.11 28.5 0.33 6 22.6
1/497 KM-28A360-497-2413 6.0-24.0 24.0 0.05 12.2 0.15 12 10.1
Remarks:
6 -0.01
-0.03
1. All values approximate.
5 -0
-0.1
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
27 3-4 1/6.4
29.5 5 1/33
32 6 1/75
34.5 7 1/170
37 8 1/387
Ratio Model No.
KM-28A360/365
A ±0.5 L ±0.2
B ±0.1
1
12
Operating
Range
Voltage
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
32.6REF
No Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
27.7REF
27.5
2-M3 Depth 4mm
DIRECTION OF ROTATION
CW/CCW
19 ±0.1
On Load
Find even More at http://www.kinmoremotor.com Page [ 52 ]
7.5

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machines
-Metal or Carbon Brush DC Motor -ATM/Robot
-Spur Gears -Toys
-Copperplate Gear Case -Cleaning Brush
-Sleeve Bronze Bushing
1/8.2 1/14.5 1/15 1/18.6 - -
1/42.3 - - - - -
1/96.3 - - - - -
1/219 - - - - -
1/497 - - - - -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/18.6 KM-28A370-18.6-12300 6.0-12.0 12.0 0.06 300 0.17 0.38 258
1/75 KM-28A370-75-1248 6.0-12.0 12.0 0.05 44.8 0.15 1.4 32
1/219 KM-28A370-219-1225 6.0-12.0 12.0 0.07 25 0.20 3.8 21
1/387 KM-28A370-387-1214 6.0-12.0 12.0 0.08 14 0.19 6.5 12
1/497 KM-28A370-497-1211 6.0-12.0 12.0 0.07 11 0.21 8 9.5
Remarks:
6 -0.01
-0.03
1. All values approximate.
B ±0.1
5 -0
-0.1
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
27 3-4 1/6.4
29.5 5 1/33
32 6 1/75
34.5 7 1/170
37 8 1/387
Ratio Model No.
A ±0.5
1
KM-28A370
Operating
Range
General Reduction Ratios
Voltage No Load On Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
12
V
L ±0.2
30.8REF
(+)
24.4REF
2-M3
Depth 4mm
DIRECTION OF ROTATION
CW/CCW
7.5
19 ±0.1
Find even More at http://www.kinmoremotor.com Page [ 53 ]
27.5

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -ATM/Robot
-Spur Gears -Toy
-Copperplate Gear Case -Cleaning Brush
-Sleeve Bronze Bushing
1/8.2 1/14.5 1/15 1/18.6 - -
1/42.3 - - - - -
1/96.3 - - - - -
1/219 - - - - -
1/497 - - - - -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/14.5 KM-28A385-14.5-121140 6.0-12.0 12.0 0.58 1142 1.8 0.8 930.1
1/42.3 KM-28A385-42.3-24260 6.0-24.0 24.0 0.13 247 0.74 3 170.5
1/96 KM-28A385-96-4.5160 3.0-5.0 4.5 1.5 161.7 3.4 3 133
1/170 KM-28A385-170-1225 6.0-12.0 12.0 0.09 25.6 0.33 4 19.8
1/497 KM-28A385-497-1210 6.0-12.0 12.0 0.13 9.3 0.22 8 8.1
Remarks:
6 -0.01
-0.03
5 -0
-0.1
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
27 3-4 1/6.4
29.5 5 1/33
32 6 1/75
34.5 7 1/170
37 8 1/387
Ratio Model No.
KM-28A380/385
A ±0.5 L ±0.2
B ±0.1
1
12
Operating
Range
General Reduction Ratios
Voltage No Load On Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
37.8REF
27.7REF
27.5
2-M3 Depth 4mm
DIRECTION OF ROTATION
CW/CCW
19 ±0.1
Find even More at http://www.kinmoremotor.com Page [ 54 ]
7.5

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -ATM/Robot
-Spur Gears -Toy
-Copperplate Gear Case -Cleaning Brush
-Sleeve Bronze Bushing
1/8.2 1/14.5 1/15 1/18.6 - -
1/42.3 - - - - -
1/96.3 - - - - -
1/219 - - - - -
1/497 - - - - -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/8.2 KM-28A390-8.2-121500 6.0-12.0 12.0 0.54 1512 2.3 1 1170
1/18.6 KM-28A390-18.6-03.6753 2.0-4.0 3.6 1.1 753.3 4.3 1 539.4
1/75 KM-28A390-75-1280 6.0-12.0 12.0 12.0 83 1.2 8 68
1/170 KM-28A390-170-2462 6.0-24.0 24.0 24.0 62.2 0.66 10 53
1/219 KM-28A390-219-1238 6.0-12.0 12.0 12.0 38 0.93 10 30.8
Remarks:
6 -0.01
-0.03
5 -0
-0.1
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
27 3-4 1/6.4
29.5 5 1/33
32 6 1/75
34.5 7 1/170
37 8 1/387
Ratio Model No.
KM-28A390/395
A ±0.5 L ±0.2
B ±0.1
1
12
Operating
Range
General Reduction Ratios
Voltage No Load On Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
46.5REF
27.7REF
27.5
2-M3 Depth 4mm
DIRECTION OF ROTATION
CW/CCW
19 ±0.1
Find even More at http://www.kinmoremotor.com Page [ 55 ]
7.5

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Garden Tool
-Spur Gears -Electric Lock
-Copperplate Gear Case -Actuator
-Sleeve Bronze Bushing
1/17.3 - - - - -
1/40 1/46 1/52 - - -
1/136 1/155 - - - -
1/409 1/466 - - - -
1/1228 1/1397 - - - -
Nominal
Voltage
Current Speed Current Torque 0.054
V A r/min A kg.cm r/min
1/17.3 KM-32A365-17.3-12558 6.0-12.0 12.0 0.27 557.4 0.75 0.9 445
1/46 KM-32A365-46-12160 6.0-12.0 12.0 0.16 158.9 0.4 1.2 134
1/105 KM-32A365-105-12106 6.0-12.0 12.0 0.23 105 0.7 3 85.3
1/136 KM-32A365-136-2460 6.0-24.0 24.0 0.07 61 0.3 4 45
1/278 KM-32A360-278-1216 6.0-12.0 12.0 0.1 15.5 0.25 6 12
Remarks:
6 -0.01
-0.03
1. All values approximate.
5.5 -0
-0.1
Your Reliable DC and Gear Motor Supplier
Number Of
Stage
17.7 3 1/15
20.4 4 1/10.6
23.1 5 1/105
25.8 6 1/278
28.5 7 1/732
Ratio Model No.
B ±0.1
KM-32A360/365
A ±0.5
3
Operating
Range
General Reduction Ratios
Voltage No Load On Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
12
L ±0.2
32.6REF
27.7REF
DIRECTION OF ROTATION
CW/CCW
Find even More at http://www.kinmoremotor.com Page [ 56 ]
26
4-M3
32
3-120°

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-Direction -Vending machine
-Carbon Brush DC Motor -Garden Tool
-Spur Gears -Electric Lock
-Zinc Die Cast Gear Case -Actuator
-Sleeve Bronze Bushing
1/17.3 - - - - -
1/40 1/46 1/52 - - -
1/136 1/155 - - - -
1/409 1/466 - - - -
1/1228 1/1397 - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/52 KM-32A380-52-07.2167 6.0-8.0 7.2 0.36 166.3 1.33 3 132.1
1/105 KM-32A385-105-12120 6.0-12.0 12.0 0.21 120.4 1.21 5 98
1/136 KM-32A385-136-06110 3.0-6.0 6.0 0.81 110.9 3.05 10 84.1
1/155 KM-32A385-155-1240 6.0-12.0 12.0 0.2 38 0.40 4 31.2
1/278 KM-32A385-278-1221 6.0-12.0 12.0 0.2 21 0.5 10 18
Remarks:
6 -0.01
-0.03
5.5 -0
-0.1
1. All values approximate.
Number Of
Stage
17.7 3 1/15
20.4 4 1/10.6
23.1 5 1/105
25.8 6 1/278
28.5 7 1/732
Ratio Model No.
Your Reliable DC and Gear Motor Supplier
B ±0.1
A ±0.5
3
KM-32A380/385
Operating
Range
Voltage
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
12
V
L ±0.2
37.8REF
27.7REF
DIRECTION OF ROTATION
CW/CCW
26
4-M3
32
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 57 ]
3-120°

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Garden Tool
-Spur Gears -Electric Lock
-Zinc Die Cast Gear Case -Actuator
-Sleeve Bronze Bushing
1/17.3 - - - - -
1/40 1/46 1/52 - - -
1/136 1/155 - - - -
1/409 1/466 - - - -
1/1228 1/1397 - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/40 KM-32A390-40-24375 6.0-24.0 24 0.21 390.1 0.95 3 333.4
1/105 KM-32A390-105-12124 6.0-12.0 12 0.34 124.2 1.68 7 104
1/155 KM-32A390-155-1230 6.0-12.0 12 0.1 29.7 0.3 6 24
1/409 KM-32A390-409-1218 6.0-12.0 12 0.2 18.4 0.75 10 15
1/466 KM-32A390-466-1210 6.0-12.0 12 0.1 10 0.3 16 8
Remarks:
6 -0.01
-0.03
1. All values approximate.
5.5 -0
-0.1
Number Of
Stage
17.7 3 1/15
20.4 4 1/10.6
23.1 5 1/105
25.8 6 1/278
28.5 7 1/732
Ratio Model No.
Your Reliable DC and Gear Motor Supplier
B ±0.1
A ±0.5
3
KM-32A390/395
Operating
Range
Voltage
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
12
V
L ±0.2
46.5REF
27.7REF
DIRECTION OF ROTATION
CW/CCW
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 58 ]
26
4-M3
32
3-120°

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending machine
-Metal Brush or Carbon Brush DC Motor -Robot
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Actuator
-Sleeve Bronze Bushing
1/17.3 - - - - -
1/40 1/46 1/52 - - -
1/136 1/155 - - - -
1/409 1/466 - - - -
1/1228 1/1397 - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/10.6 KM-32A500-10.6-06720 3.0-6.0 6.0 0.12 707.3 0.46 0.2 585.3
1/155 KM-32A500-155-0354 3.0-6.0 5.0 0.05 34.4 0.3 2 27
1/466 KM-32A500-466-0610 3.0-6.0 6.0 0.04 10 0.18 4 8
1/732 KM-32A500-732-064.8 3.0-6.0 6.0 0.08 4.6 0.24 7 3.6
1/1228 KM-32A500-1228-062.8 3.0-6.0 6.0 0.09 2.7 0.17 7 2.3
Remarks:
6 -0.01
-0.03
1. All values approximate.
5.5 -0
-0.1
Number Of
Stage
17.7 3 1/15
20.4 4 1/10.6
23.1 5 1/105
25.8 6 1/278
28.5 7 1/732
Ratio Model No.
Your Reliable DC and Gear Motor Supplier
KM-32A500
A ±0.5 L ±0.2
B ±0.1
3
Operating
Range
Voltage
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
12
19.3REF
32REF
32
DIRECTION OF ROTATION
CW/CCW
26
4-M3
No Load On Load
3-120°
Find even More at http://www.kinmoremotor.com Page [ 59 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush And Carbon Brush DC Motor -Robot
-Spur Gears -Satellite/Solar System
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/207 1/209 1/238 1/321 1/474 1/534
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/57 KM-32F300-57-1274 6.0-12.0 12.0 0.02 130 0.06 0.28 105
1/207 KM-32F300-207-1236 6.0-12.0 12.0 0.02 36 0.06 1 29
1/321 KM-32F300-321-1223 6.0-12.0 12.0 0.02 23 0.06 1.4 18.7
1/474 KM-32F300-474-0317 2.0-3.0 3.0 0.06 17 0.17 1.6 13.9
1/534 KM-32F300-534-1220 6.0-12.0 12.0 0.04 20 0.14 5 15
Remarks:
66.5
Ratio Model No.
1. All values approximate.
R13
Number Of
Stage
66.5*32*11 mm 3-4 1/57
Your Reliable DC and Gear Motor Supplier
40
32
KM-32F300
Operating
Range
Voltage
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
R3
R4
135°
7 -0.01
-0.03
24.4
C ±10
A ±0.5
B ±0.1
5 -0
-0.1
1
6×1
1.5
4-2
12.4
11
7
39
1.5
2- 12
40.8
26.3 10.5
DIRECTION OF ROTATION
CW/CCW
4- 3.2
RED BLACK
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 60 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush And Carbon Brush DC Motor -Robot
-Spur Gears -Satellite/Solar System
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/207 1/209 1/238 1/321 1/474 1/534
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/57 KM-32F300-57-1274 6.0-12.0 12.0 0.18 236 0.5 1.2 210
1/207 KM-32F370-207-2430 6.0-24.0 24 0.02 30.7 0.07 3 26.6
1/321 KM-32F370-321-2420 6.0-24.0 24 0.02 19.8 0.07 4.5 17
1/474 KM-32F370-474-2413 6.0-24.0 24 0.02 13.4 0.07 6.5 11.6
1/534 KM-32F370-534-2412 6.0-24.0 24 0.02 11.9 0.07 8 10.3
Remarks:
66.5
1. All values approximate.
Number Of
Stage
66.5*32*11 mm 3-4 1/57
Ratio Model No.
R13
Your Reliable DC and Gear Motor Supplier
40
32
KM-32F370
Operating
Range
Voltage
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
R4
135°
C ±10
R3
7 -0.01
-0.03
A ±0.5
B ±0.1
5 -0
-0.1
30.8
1
6×1
1.5
4-2
24.4
11
7
39
1.5
2- 12
40.8
26.3 10.5
DIRECTION OF ROTATION
CW/CCW
No Load On Load
4- 3.2
RED BLACK
Find even More at http://www.kinmoremotor.com Page [ 61 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length L(mm)
Common King-size
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Dispenser
-Spur Gears -Satellite/Solar System
-Zinc Die Cast Gear Case Valve/EPB/Robot/Model
-Sleeve Bronze Bushing -Power Tool
1/9.3 1/10 - - - -
1/19.5 1/20 1/24 1/30 - -
1/50 1/56 1/60 1/69 1/70 1/190
1/150 1/168 1/180 1/210 1/259 1/270
1/450 1/540 1/622 1/630 1/810 1/1084
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/6.5 KM-37B3530-6.5-121060 6.0-12.0 12.0 0.2 1060 0.6 0.34 818.6
1/70 KM-37B3530-70-1286 6.0-12.0 12.0 0.08 86.4 0.26 1.5 77.3
1/210 KM-37B3530-210-0644 3.0-6.0 6.0 0.42 44 1.28 10 38.2
1/622 KM-37B3530-622-0503 3.0-6.0 5.0 0.06 3.4 0.2 10 2.3
1/810 KM-37B3530-810-0502.5 3.0-6.0 5.0 0.06 2.5 0.2 13 1.8
Remarks:
18 22
21.5 25.2
24
26.7
27.7
30.7
29 31.7
6 -0.01
-0.03
5.5 0
-0.1
Model No.
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
B ±0.1
Number Of
Stage
KM-37B3530
2 1/6.5
3 1/15
4 1/40
5 1/125
6
A ±0.5
6
1/360
Operating
Range
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
L ±0.2 30.8REF
Voltage
No Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
12
34.6REF
7
31
37
DIRECTION OF ROTATION
CW/CCW
3-120°
On Load
6-M3
MAX Depth 3.5mm
Find even More at http://www.kinmoremotor.com Page [ 62 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length L(mm)
Common King-size
24
26.7
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Dispenser
-Spur Gears -Satellite/Solar system
-Zinc Die Cast Gear Case -Valve/ EPB/Robot/Model
-Sleeve Bronze Bushing -Power Tool
1/9.3 1/10 - - - -
1/19.5 1/20 1/24 1/30 - -
1/50 1/56 1/60 1/69 1/70 1/190
1/150 1/168 1/180 1/210 1/259 1/270
1/450 1/540 1/622 1/630 1/810 1/1084
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/40 KM-37B3540-40-24250 6.0-24.0 24.0 0.16 247.2 0.56 3.5 211.2
1/72 KM-37B3540-72-24110 6.0-24.0 24.0 0.07 109 0.53 6 85.5
1/150 KM-37B3540-150-1245 6.0-12.0 12.0 0.24 45.2 0.55 8 40
1/259 KM-37B3540-259-2430 6.0-24.0 24.0 0.07 31.4 0.27 12 28
1/270 KM-37B3540-270-2421 6.0-24.0 24.0 0.08 21 0.19 12 19.6
Remarks:
1. All values approximate.
Number Of
Stage
18 22 2
21.5 25.2 3
29
Your Reliable DC and Gear Motor Supplier
1/6.5
27.7 4 1/40
30.7
31.7
6 -0.01
-0.03
5.5 0
-0.1
Ratio Model No.
5
6
B ±0.1
A ±0.5
KM-37B3540
6
1/125
1/360
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
1/15
Operating
Range
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
12
V
L ±0.2 40REF
Voltage
34.6REF
7
DIRECTION OF ROTATION
CW/CCW
3-120°
No Load On Load
31
37
6-M3
MAX Depth 3.5mm
Find even More at http://www.kinmoremotor.com Page [ 63 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length L(mm)
Common King-size
24
26.7
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush Or Carbon Brush DC Motor -Dispenser
-Spur Gears -Satellite/Solar System
-Zinc Die Cast Gear Case -Valve/ EPB/Robot/Model
-Sleeve Bronze Bushing -Power Tool
1/9.3 1/10 - - - -
1/19.5 1/20 1/24 1/30 - -
1/50 1/56 1/60 1/69 1/70 1/190
1/150 1/168 1/180 1/210 1/259 1/270
1/450 1/540 1/622 1/630 1/810 1/1084
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/6.5 KM-37B500-6.5-24760 6.0-24.0 24.0 0.03 734.6 0.06 0.09 601.8
1/90 KM-37B500-90-0640 3.0-6.0 6.0 0.04 40.2 0.12 1.2 33.4
1/150 KM-37B500-150-0526 3.0-6.0 5.0 0.04 26.1 0.15 1.2 22
1/450 KM-37B500-450-0605 3.0-6.0 6.0 0.03 6 0.12 2.6 4.5
1/1084 KM-37B500-1084-02.502 2.0-3.0 2.5 0.05 2 0.09 4 1.7
Remarks:
1. All values approximate.
Number Of
Stage
18 22 2
21.5 25.2 3
29
Your Reliable DC and Gear Motor Supplier
1/6.5
27.7 4 1/40
30.7
31.7
Ratio Model No.
6 -0.01
-0.03
5
6
5.5 -0
-0.1
KM-37B500
A ±0.5
B ±0.1
1/125
1/360
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
1/15
Operating
Range
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
V
6
Voltage
L ±0.2
12
DIRECTION OF ROTATION
19.3REF CW/CCW
32REF
6-M3 Depth 3.5mm
32
7
3-120°
37
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 64 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length L(mm)
Common
18
21.5
26.7 30.7
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush Or Carbon Brush DC Motor -Dispenser
-Spur Gears -Satellite/Solar System
-Zinc Die Cast Gear Case -Valve/EPB/Robot/Model
-Sleeve Bronze Bushing -Power Tool
1/9.3 1/10 - - - -
1/19.5 1/20 1/24 1/30 - -
1/50 1/56 1/60 1/69 1/70 1/190
1/150 1/168 1/180 1/210 1/259 1/270
1/450 1/540 1/622 1/630 1/810 1/1084
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/10 KM-37B520-10-24310 6.0-24.0 24.0 0.02 310 0.03 0.09 270
1/90 KM-37B520-19-2435 6.0-24.0 24.0 0.02 34.5 0.03 0.73 30
1/270 KM-37B520-270-1211 6.0-12.0 24.0 0.04 10.8 0.07 2.4 9.3
1/540 KM-37B520-540-1206 6.0-12.0 12.0 0.04 6 0.08 5 4.5
1/810 KM-37B520-810-1203.7 6.0-12.0 12.0 0.05 3.7 0.06 6 3
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
Remarks:
King-size
29 31.7
22 2
25.2 3
Model No.
1. All values approximate.
6 -0.01
-0.03
Your Reliable DC and Gear Motor Supplier
5.5 -0
-0.1
Number Of
Stage
24 27.7 4
5
6
KM-37B520
A ±0.5
B ±0.1
1/6.5
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
6
1/15
1/40
1/125
1/360
Operating
Range
V
12
Voltage
L ±0.2 22.8REF
(+)
33
7
31
37
General Reduction Ratios
DIRECTION OF ROTATION
CW/CCW
3-120°
No Load On Load
6-M3
MAX Depth 3.5mm
Find even More at http://www.kinmoremotor.com Page [ 65 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length L(mm) Number Of
Common King-size Stage
18
21.5
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush Or Carbon Brush DC Motor -Dispenser
-Spur Gears -Satellite And Solar System
-Zinc Die Cast Gear Case -Valve/EPB/Robot/Model
-Sleeve Bronze Bushing -Power Tool
1/9.3 1/10 - - - -
1/19.5 1/20 1/24 1/30 - -
1/50 1/56 1/60 1/69 1/70 1/190
1/150 1/168 1/180 1/210 1/259 1/270
1/450 1/540 1/622 1/630 1/810 1/1084
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/10 KM-37B528-10-121032 6.0-12.0 12.0 0.21 1032 0.89 0.6 775.4
1/60 KM-37B528-60-24138 6.0-24.0 24.0 0.08 135.8 0.23 1.8 118.9
1/120 KM-37B528-120-1272 6.0-12.0 12.0 0.13 72 0.66 6 56.8
1/589 KM-37B528-589-1210 6.0-12.0 12.0 0.1 10 0.18 12 9.3
1/810 KM-37B528-810-2410 6.0-24.0 24.0 0.06 10.3 0.12 15 9
Remarks:
24 27.7 4
26.7 30.7
29 31.7
6 -0.01
-0.03
Ratio Model No.
1. All values approximate.
5 -0
-0.1
22 2
25.2 3
Your Reliable DC and Gear Motor Supplier
5
6
KM-37B528
A ±0.5
B ±0.1
1/6.5
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
1/15
1/40
1/125
1/360
Operating
Range
V
Voltage
6-M3 Depth 3.5mm
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
6
12
L ±0.2
29.5REF
32.6REF
7
? 31
DIRECTION OF ROTATION
CW/CCW
3-120°
37
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 66 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length L(mm) Number Of
Common King-size Stage
18
21.5
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush Or Carbon Brush DC Motor -Dispenser
-Spur Gears -Satellite And Solar System
-Zinc Die Cast Gear Case -Valve/EPB/Robot/Model
-Sleeve Bronze Bushing -Power Tool
1/9.3 1/10 - - - -
1/19.5 1/20 1/24 1/30 - -
1/50 1/56 1/60 1/69 1/70 1/190
1/150 1/168 1/180 1/210 1/259 1/270
1/450 1/540 1/622 1/630 1/810 1/1084
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/40 KM-37B545-10-241560 6.0-24.0 24.0 0.6 1511 2.33 2.5 1265
1/72 KM-37B545-40-12155 6.0-12.0 12.0 0.3 155.3 1.23 6 127.8
1/150 KM-37B545-150-1237.5 6.0-12.0 12.0 0.34 37.5 0.65 10 35.3
1/259 KM-37B545-210-1222 6.0-12.0 12.0 0.16 21.6 0.38 13 19.4
1/270 KM-37B545-810-123.7 6.0-24.0 12.0 0.24 3.7 0.3 30 19.6
Remarks:
24 27.7 4
26.7 30.7
29 31.7
6 -0.01
-0.03
Ratio Model No.
1. All values approximate.
5.5 -0
-0.1
22 2
25.2 3
Your Reliable DC and Gear Motor Supplier
5
6
A ±0.5
B ±0.1
KM-37B540/545
6
1/6.5
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
1/15
1/40
1/125
1/360
Operating
Range
V
Voltage
50REF
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
12
L ±0.2
36REF
7
DIRECTION OF ROTATION
CW/CCW
3-120°
No Load On Load
31
37
6-M3
MAX Depth 3.5mm
Find even More at http://www.kinmoremotor.com Page [ 67 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length L(mm) Number Of
Common King-size Stage
18
21.5
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush Or Carbon Brush DC Motor -Dispenser
-Spur Gears -Satellite/Solar System
-Zinc Die Cast Gear Case -Valve/EPB/Robot/Model
-Sleeve Bronze Bushing -Power Tool
1/9.3 1/10 - - - -
1/19.5 1/20 1/24 1/30 - -
1/50 1/56 1/60 1/69 1/70 1/190
1/150 1/168 1/180 1/210 1/259 1/270
1/450 1/540 1/622 1/630 1/810 1/1084
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/19.5 KM-37B555-19.5-241333 6.0-24.0 24.0 1.1 1326 5.42 5.6 1166
1/69 KM-37B555-69-1280 6.0-12.0 12.0 0.26 80.3 1.4 10 67
1/103 KM-37B555-106-1270 6.0-12.0 12.0 0.24 70 1.3 15 62.4
1/150 KM-37B555-150-0621 3.0-6.0 6.0 0.18 21 2.0 17.5 14.2
1/210 KM-37B555-210-1250 6.0-12.0 12.0 0.43 51 1.5 20 47.0
Remarks:
24 27.7 4
26.7 30.7
29 31.7
6 -0.01
-0.03
5.5 -0
-0.1
22 2
25.2 3
Ratio Model No.
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
5
6
A ±0.5
B ±0.1
6
KM-37B550/555
1/6.5
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
12
L ±0.2
1/15
1/40
1/125
1/360
Operating
Range
V
Voltage
57REF
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
36REF
7
DIRECTION OF ROTATION
CW/CCW
3-120°
No Load On Load
31
37
6-M3
MAX Depth 3.5mm
Find even More at http://www.kinmoremotor.com Page [ 68 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length L(mm) Number Of
Common King-size Stage
18
21.5
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal Brush Or Carbon Brush DC Motor -Dispenser
-Spur Gears -Satellite/Solar System
-Zinc Die Cast Gear Case -Valve/EPB/Robot/Model
-Sleeve Bronze Bushing -Power Tool
1/9.3 1/10 - - - -
1/19.5 1/20 1/24 1/30 - -
1/50 1/56 1/60 1/69 1/70 1/190
1/150 1/168 1/180 1/210 1/259 1/270
1/450 1/540 1/622 1/630 1/810 1/1084
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/9.6 KM-37B590-9.6-241400 6.0-24.0 24.0 0.5 1383 3.3 4 1124
1/30 KM-37B590-30-12276 6.0-12.0 12.0 0.45 276 3.0 7 242
1/50 KM-37B590-50-12166 6.0-12.0 12.0 0.45 166 3.0 12 145
1/70 KM-37B590-70-12120 6.0-12.0 12.0 0.45 120 3.0 16.5 104
1/90 KM-37B590-90-1290 6.0-12.0 12.0 0.45 92 3.0 22 80
Remarks:
24 27.7 4
26.7 30.7
29 31.7
6 -0.01
-0.03
5.5 -0
-0.1
22 2
25.2 3
Ratio Model No.
1. All values approximate.
Your Reliable DC and Gear Motor Supplier
5
6
A ±0.5
B ±0.1
6
KM-37B590/595
12
L ±0.2
1/6.5
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
1/15
1/40
1/125
1/360
Operating
Range
V
Voltage
67REF
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
36REF
7
DIRECTION OF ROTATION
CW/CCW
3-120°
No Load On Load
31
37
6-M3
MAX Depth 3.5mm
Find even More at http://www.kinmoremotor.com Page [ 69 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Garden Tool
-Spur Gears -Vacuum Cleaner
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/142.5 1/155.5 1/223 1/446 - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/105 KM-38F3530-105-1257 6.0-12.0 12.0 0.08 57.3 0.26 2.3 51.6
1/155.5 KM-38F3530-155.5-1239 6.0-12.0 12.0 0.08 38.7 0.26 3.4 35
1/223 KM-38F3530-223-1227 6.0-12.0 12.0 0.08 27 0.26 4.6 24
1/446 KM-38F3530-446-1214 6.0-12.0 12.0 0.08 13.5 0.26 7.6 12
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
Remarks:
64*38*12 mm
1. All values approximate.
64.4
Ratio Model No.
Your Reliable DC and Gear Motor Supplier
7.2
50
31
4-R12.5
Number Of
Stage
4-5 1/105
KM-38F3530
Operating
Range
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
26.5
38
A A
Voltage
6 -0.01
-0.03
1
5.5 -0
-0.1
A-A
90°
4-M3
General Reduction Ratios
No Load
4- 4
A ±0.5
B ±0.1
1.5
12
2- 12
2.75
34.5REF
30REF
On Load
Find even More at http://www.kinmoremotor.com Page [ 70 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Garden Tool
-Spur Gears -Vacuum Cleaner
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/142.5 1/155.5 1/223 1/446 - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/105 KM-38F3540-105-12105 6.0-12.0 12.0 0.3 110.7 1.3 8 93
1/155.5 KM-38F3540-155.5-1271 6.0-12.0 12.0 0.3 71 1.3 10 62.8
1/223 KM-38F3540-223-1250 6.0-12.0 12.0 0.3 50 1.3 12 24
1/446 KM-38F3540-446-127.2 6.0-12.0 12.0 0.04 7.2 0.2 18 6
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
Remarks:
64*38*12 mm
64.4
1. All values approximate.
7.2
50
Model No.
Your Reliable DC and Gear Motor Supplier
31
4-R12.5
Number Of
Stage
4-5 1/105
KM-38F3540
Operating
Range
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
26.5
38
V
A A
Voltage
1
A-A
90°
2- 12
4-M3
4- 4
1.5
General Reduction Ratios
No Load
12
A ±0.5
B ±0.1
2.75
5.5 -0
-0.1
6 -0.01
-0.03
34.5REF
40REF
On Load
Find even More at http://www.kinmoremotor.com Page [ 71 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear box length
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Garden Tool
-Spur Gears -Vacuum Cleaner
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/142.5 1/155.5 1/223 1/446 - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/105 KM-38F500-105-0626 3.0-6.0 6.0 0.03 25.7 0.1 0.85 20.7
1/155.5 KM-38F500-155.5-1245 6.0-12.0 12.0 0.06 44.3 0.21 4 36
1/223 KM-38F500-223-0325 2.0-3.0 3.0 0.12 25.6 0.55 2.9 19.8
1/446 KM-38F500-446-0311 2.0-3.0 3.0 0.17 11.2 0.55 5 8.6
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
Remarks:
64*38*12 mm
64.4
Model No.
1. All values approximate.
7.2
50
Your Reliable DC and Gear Motor Supplier
31
4-R12.5
Number Of
Stage
4-5 1/105
KM-38F500
Operating
Range
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
26.5
38
Voltage
A A
1
6 -0.01
-0.03
5.5 +0
-0.1
A-A
90°
Positive Pole
General Reduction Ratios
No Load
B ±0.1
4-M3
4- 4
A ±0.5
2- 12
1.5 2.75
12
32
19.5
On Load
Find even More at http://www.kinmoremotor.com Page [ 72 ]
(+)

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Garden Tool
-Spur Gears -Vacuum Cleaner
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/142.5 1/155.5 1/223 1/446 - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/105 KM-38F520-105-1252 6.0-12.0 12.0 0.05 52 0.2 3 45
1/155.5 KM-38F520-155.5-1273 6.0-12.0 12.0 0.16 73 0.75 6 60.6
1/223 KM-38F520-223-1231 6.0-12.0 12.0 0.06 32 0.4 8 24
1/446 KM-38F520-446-1212 6.0-12.0 12.0 0.05 12.3 0.23 10 10.5
Remarks:
64*38*12 mm
64.4
Model No.
1. All values approximate.
7.2
50
Your Reliable DC and Gear Motor Supplier
31
4-R12.5
Number Of
Stage
4-5
KM-38F520
Positive Pole
1/105
Operating
Range
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
26.5
38
Voltage
A A
1
6 -0.01
-0.03
5.5 +0
-0.1
90°
Positive Pole
B ±0.1
4-M3
4- 4
A ±0.5
1.5 2.75
12
2- 12
33REF
22.8REF
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 73 ]
A-A
(+)

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal or Carbon Brush DC Motor -Business Machine
-Spur Gears -Duplicating Machine
-Zinc Die Cast Gear Case -Valve
-Sleeve Bronze Bushing -RC Toy
1/1026 - - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/766 KM-38L130-766-1210 6.0-12.0 12.0 0.04 9.4 0.13 4 8
1/766 KM-38L130-766-0605 3.0-6.0 6.0 0.03 5 0.13 4 3
1/766 KM-38L130-1026-0608 3.0-6.0 6.0 0.03 7.8 0.35 5 6.7
1/766 KM-38L130-1026-1207 6.0-12.0 12.0 0.04 7 0.13 7 6
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
Remarks:
64*38*29 mm
64
Model No.
1. All values approximate.
28
13
Your Reliable DC and Gear Motor Supplier
12.9
Number Of
Stage
4- 3.1
KM-38L130
38
33
6 1/766
Operating
Range
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
Voltage
44.5REF
15.4REF
29
13
12
R1
1.2
B ±0.1
A ±0.5
1.5
(+)
6- 0.01
-0.03
5.15
20.4REF
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 74 ]
5.5 -0
-0.1
19.5
4-R12.5

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Metal or Carbon Brush DC Motor -Business Machine
-Spur Gears -Duplicating Machine
-Zinc Die Cast Gear Case -Valve
-Sleeve Bronze Bushing -RC Toy
1/1026 - - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/766 KM-38L180-766-1217 6.0-12.0 12.0 0.13 17.2 0.45 9 14.8
1/766 KM-38L180-766-0316 2.0-3.0 3.0 0.33 16.9 2 8 12
1/766 KM-38L180-1026-1204 6.0-12.0 12.0 0.03 4.5 0.09 8 3.7
1/766 KM-38L180-1026-2409 6.0-24.0 24.0 0.03 9 0.13 12.5 7.5
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
Remarks:
64*38*29 mm
64
Model No.
1. All values approximate.
28
13
Your Reliable DC and Gear Motor Supplier
12.9
Number Of
Stage
4- 3.1
KM-38L180
38
33
6 1/766
Operating
Range
General Reduction Ratios
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
V
Voltage
51.3REF
15.4REF
29
13
12
R1
1.2
B ±0.1
A ±0.5
5.5 -0
-0.1
1.5
(+)
6- 0.01
-0.03
5.15
20.4REF
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 75 ]
19.5
4-R12.5

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
70*40*20 mm
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Air Pillow Machine
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/32 1/53 1/57 1/81 1/158 1/169 1/240 1/530 1/564
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/57 KM-40F3540-57-12140 6.0-12.0 12.0 0.1 140 0.67 3.3 114.5
1/158 KM-40F3540-158-1250 6.0-12.0 12.0 0.1 50.3 0.67 9 41.2
1/240 KM-40F3540-240-1233 6.0-12.0 12.0 0.1 33 0.67 14 27
1/530 KM-40F3540-530-1215
6.0-12.0 12.0 0.1 14.8 0.67 30 12.3
Remarks:
Number Of
Stage
1. All values approximate.
6
2- 14
1
Model No.
Your Reliable DC and Gear Motor Supplier
34
20
KM-40F3540
A ±0.5
B ±0.1
Operating
Range
Voltage
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
1
V
7 -0
-0.1
40REF
34.5REF
8 -0.01
-0.03
70.5
4- 4.5
7
20
30
40
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 76 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
70*40*20 mm
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Air Pillow Machine
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
6 1/32 1/53 1/57 1/81 1/158 1/169 1/240 1/530 1/564
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/32 KM-40F550-32-18226 6.0-12.0 12.0 0.35 225.8 1.27 6 189.7
1/81 KM-40F550-81-12154 6.0-12.0 12.0 0.9 148 4.2 20 121.2
1/158 KM-40F550-158-1232 6.0-12.0 12.0 0.36 32.7 1.45 30 25.4
1/169 KM-40F550-169-2427 6.0-24.0 24.0 0.1 27.2 0.62 30.6 22
Remarks:
Number Of
Stage
1. All values approximate.
2- 14
Ratio Model No.
1
Your Reliable DC and Gear Motor Supplier
34
20
KM-40F550/555
A ±0.5
B ±0.1
Operating
Range
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
1
V
7 -0
-0.1
35.8REF
8 -0.01
-0.03
57REF
Voltage
70.5
4- 4.5
7
20
General Reduction Ratios
30
40
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 77 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Air Pillow Machine
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
92*42*20 mm 6 1/14.6 1/36.9 1/189 1/244 1/531 1/554 1/609 1/818 -
Ratio Model No.
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/531 KM-42F3540-531-1205 6.0-12.0 12.0 0.06 4.6 0.22 30 3.5
1/554 KM-42F3540-554-1215.5 6.0-12.0 12.0 0.21 15.5 0.5 10 14.5
1/818 KM-42F3540-818-129.5 6.0-12.0 12.0 0.28 9.5 0.68 40 8.3
Remarks:
1. All values approximate.
92
24
40
Number Of
Stage
Your Reliable DC and Gear Motor Supplier
12
KM-42F3540
Operating
Range
Voltage
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
42
34
4- 4.5
-
V
(-)
8 -0.01
-0.03
7 -0
-0.1
A ±0.5
B ±0.1
52
General Reduction Ratios
1
20
? 14
2.5
40REF
34.5REF
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 78 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Air pillow Machine
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
92*42*20 mm 6 1/14.6 1/36.9 1/189 1/244 1/531 1/554 1/609 1/818 -
Ratio Model No.
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/189 KM-42F545-189-1234 6.0-12.0 12.0 0.3 34.4 1.5 23 28.7
1/224 KM-42F545-224-1227 6.0-12.0 12.0 0.3 26.5 1.5 30 22.5
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
Remarks:
92
24
40
Number Of
Stage
1. All values approximate.
12
(+)
Your Reliable DC and Gear Motor Supplier
KM-42F540/545
Operating
Range
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
42
34
4- 4.5
V
8 -0.01
-0.03
7 -0
-0.1
Voltage
A ±0.5
B ±0.1
1
20
52
General Reduction Ratios
? 14
2.5
50REF
35.8
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 79 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Air Pillow Machine
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
92*42*20 mm 6 1/14.6 1/36.9 1/189 1/244 1/531 1/554 1/609 1/818 -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/189 KM-42F550-189-1242 6.0-12.0 12.0 0.6 41.7 2.4 40 35.5
1/154 KM-42F550-554-13.888 6.0-12.0 12.0 1.3 38 2 23 36
1/609 KM-42F550-609-1211 6.0-12.0 12.0 0.4 10.4 1 56 9.7
Remarks:
92
1. All values approximate.
24
40
Number Of
Stage
Your Reliable DC and Gear Motor Supplier
12
(+)
Ratio Model No.
KM-42F550/555
Operating
Range
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
42
34
4- 4.5
V
8 -0.01
-0.03
Voltage
7 -0
-0.1
A ±0.5
B ±0.1
1
20
52
? 14
2.5
57REF
35.8
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 80 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
97*48*23 mm 4
Ratio
Features: Typical Applications:
-Bi-Direction -Vending Machine
-Carbon Brush DC Motor -Air Pillow Machine
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/108 1/147 1/558 - - - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/558 KM-48F3540-558-1205
6.0-12.0 12.0 0.09 5.2 0.21 30 4.3
Remarks:
97
1. All values approximate.
43.5
Your Reliable DC and Gear Motor Supplier
36
32
Number Of
Stage
Model No.
32.5
KM-48F3540
Operating
Range
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
42
41
6 -0
-0.1
V
+
Voltage
R21
4-M4
R8
56
23 2-A±0.5
14
2-1 2-B±0.1
8 -0.01
-0.03
2- 14
40RED
4.5REF
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 81 ]

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
97*48*23 mm 4
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Air Pillow Machine
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Model
-Sleeve Bronze Bushing
1/108 1/147 1/558 - - - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/147 KM-48F555-147-1230
6.0-12.0 12.0 0.23 30 0.95 24 24
Remarks:
97
1. All values approximate.
43.5
Your Reliable DC and Gear Motor Supplier
36
32
Number Of
Stage
+
Model No.
32.5
KM-48F550/555
Operating
Range
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
42
41
6 -0
-0.1
V
R21
4-M4
R8
Voltage
56
23 2-A±0.5
14
2-1 2-B±0.1
8 -0.01
-0.03
2- 14
40RED
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 82 ]
35.8REF

Customization:
1.Length A, B
2.Technical Data
3.Shaft Shape
Gear Box Length
L (mm)
97*48*23 mm 4
Ratio
Features: Typical Applications:
-Bi-direction -Vending Machine
-Carbon Brush DC Motor -Air pillow Machine
-Spur Gears -Power Tool
-Zinc Die Cast Gear Case -Industrials
-Sleeve Bronze Bushing
1/108 1/147 1/558 - - - - - -
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/108 KM-48F775-108-2432
6.0-24.0 24.0 0.17 31.9 0.56 24 29.1
Remarks:
97
1. All values approximate.
32.5
36
43.5
32
Number Of
Stage
Model No.
Your Reliable DC and Gear Motor Supplier
KM-48F770/775
Operating
Range
General Reduction Ratios
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
42
Positive Pole
41
V
R21
2- 14
4-M4
R8
Voltage
1
23
1
14
2-A ±0.5
2- B ±0.1
6 0
-0.1
8 -0.01
-0.03
38REF
43.8REF
66REF
No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 83 ]
41.8REF

56*53*42.5 mm
Features: Typical Applications:
-Bi-direction
-Metal Brush DC Motor -Home Appliance
-Nylon Glass Fiber Gear Case -Water Meter
-Water-proof
-Copper and Powder Metallurgy Gears
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/2000 KM-36F1-500-2000-0301.6 2.0-3.0 3.0 0.04 1.6 0.07 3 1.4
Remarks:
30
Gear Box Length
L (mm)
1. All values approximate.
General Reduction
Ratios
1/2000
Ratio Model No.
Your Reliable DC and Gear Motor Supplier
Motor:
Red & Yellow (26AWG)
(From left to rigth)
Red wire length:275±10mm
Yellow wire length:265±10mm
2.2
16
5
3
1
KM-36F1-500
18 24.5
Logo 0.1~0.2
Operating
Range
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
No Load
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
V
Switch:
Blue & Green (26AWG)
(From Left to right)
Blue wire length:275±10mm
Green wire length:275±10mm
36
Voltage
13.5
30.5
4- 5.5
4- 3.5
8
77.5°
8
45
39
36
50
56
4.6 +0.1
+0
β
Switch:
WK1-01A-0136
17.5
22.5
53
On Load
Find even More at http://www.kinmoremotor.com Page [ 84 ]

47
42
33
4-R4
Features: Typical Applications:
-Bi-direction 90° Rotation Angle
-Metal Brush DC Motor -Home Appliance
-Copper and POM Gears -Water Meter
-ABS Gear Case
-Water-proof
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/1980 KM-42F1-320-1980-0301.6 2.0-3.0 3.0 0.03 1.6 0.06 3 1.3
Remarks:
2-R3 27
Gear Box Length
L (mm)
33
42
4.6
1. All values approximate.
General Reduction
Ratios
47*42*37.4 mm 1/1980
Ratio Model No.
8
Your Reliable DC and Gear Motor Supplier
13.4±0.05
KM-42F1-320
Operating
Range
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
18.2
4- 3.2
Through-hole
37.4
15.7
V
3
2
5.8
(7.4)
16.8
5.95
26.6
1.5
Exposed lead75±5
Black wire
24AWG
Voltage No Load
9
18.1
7.2
27
2- 5
Red wire
24AWG
On Load
27
Heat-shrink tubes
Find even More at http://www.kinmoremotor.com Page [ 85 ]

64.5
32
Gear Box Length
L (mm)
Features: Typical Applications:
-Bi-Direction
-Metal Brush DC Motor -Home Appliance
-Nylon Glass Fiber Gear Case -Water Meter
-Water-proof
-Copper and Powder Metallurgy Gears
Nominal
Voltage
Current Speed Current Torque Speed
V A r/min A kg.cm r/min
1/2357 KM-46Y320-2357-0302.5 2.0-3.0 3.0 0.06 2.6 0.14 6 2
Remarks:
+
G
Green
Blue
Red
Yellow
49
40
Electrical schematic diagram:
1. All values approximate.
General Reduction
Ratios
64.5*49*32.1mm 1/2357
Ratio Model No.
Your Reliable DC and Gear Motor Supplier
36.5
( 26.4)
KM-46Y320
Operating
Range
Unit Conversion: 1g.cm≈0.098mN.m≈0.014oz.in 1mm=0.039in 1g=0.035oz
2. Customized electric performance on request by using suitable dc motor windings and ratio.
3. Available with required shaft length, D-shape size and length, grease type etc.
8
1
Inside switch:KFC-W-04-4(R)
6
(32.1)
29.1
V
11
16.5
3.5
Heat-shrink tubes
Ribbon
Heat-shrink tubes
4.5
Green
WL:PVC UL 1007#26AWG
GREEN/BULE WIRE (ROHS)
Exposed lead 110
Red
100
Terminal:5264-2P
WL:PVC UL 1007#26AWG
RED/YELLOW WIRE (ROHS)
Yellow
Blue
Voltage No Load On Load
Find even More at http://www.kinmoremotor.com Page [ 86 ]

Benefits of working with Kinmore Motor
Excellent Sales Service
• Independent office in the urban city, talented team of sales and engineers
providing flexible, professional, prompt and customized services.
• More than 8 years’ exporting experience
Quality Control
• The passing rate of finished products is no less than 99.7%.
Green light for customers’ participation during the whole
Process of your projects
• Welcome the buyer to join in the products’ development and design.
Comprehensive ability
• Delivery on time
• Knowing well the target market
• Supplying Turnkey solutions
• Supporting buyer accessories
R&D and Innovative ability
• At least 1 new motor developed per month
SHENZHEN KINMORE MOTOR CO.,LTD
Add: 1403B Nangang Business Building, No. 1428 Qianhai Road,
Nanshan District, Shenzhen China
Tel: 86-755-21677419/86218176
Fax: 86-755-26470091
Email: kinmore@kinmoremotor.com
Website:www.kinmoremotor.com
Your Reliable DC and Gear Motor Supplier
Kinmore Motor Copyright reserved 2012