Download - RCBS

case PreP case PreP
A B
A Hand Case Neck Turner B Case Neck Turning Accessories C Pilot/Neck Reamers
The RCBS ® Hand Case Neck Turner is designed to “peel” the
brass from the outside of your case necks to a consistent
thickness. Most commercially available brass has variances in
the case neck thickness. This leads to case neck concentricity
and bullet run-out issues. Truing up the case neck produces
more consistent and accurate hand loaded ammunition.
The cutter portion uses caliber specific pilot/mandrels (sold
separately) to guide the case neck. The cutter design features
the ability to “zero” the cutter to the pilot/mandrel and then
use the micrometer adjustment to dial the desired case neck
thickness in .0005” increments. The cutter can also be set for
right or left handed use.
The Quick Change Case Holder has many advantages over the
competition. Most other units use a “tap wrench” design to
hold cartridge cases. Though this is great for threading holes
with a self feeding tap, it does nothing to feed your case neck
to the cutter. The RCBS Quick Change Case Holder features
an ergonomic design that allows you to rotate the case and put
forward pressure to feed the case neck to the cutter. The quick
case change feature helps to speed up the process without
having to use small obtrusive thrumbscrews.
90401 Hand Case Neck Turner
w/ Quick Change Case Holder $78.95
90402 Quick Change Case Holder $39.95
90405-27 Hand CNT Pilot .17-.500 $11.95
Hand Case Neck Turner Pilots: $11.95
See “D” on page 23 for list.
Case Neck Turner w/Auto Feed pictured above
Two tools for fast, easy removal of excessive neck thickness
or variation in case thickness. They guide the cutter over the
sized cartridge case neck and are supported by the special
pilot/reamer. The inside and outside of the neck are turned
simultaneously. The Auto Feed Attachment (for Case Trimmer—2
and Trim Pro ® Manual Case Trimmer) advances the cutting tool
evenly over the case neck with each turn of the trimmer handle.
Note: Not to be used with trim Pro Power Case trimmer.
98860 Case Neck Turner w/ Auto Feed $90.95
98861 Case Neck Turner $43.95
Pilot/Neck Reamers: $11.95
See “C” on page 23 for list.
Pilot/Neck Reamer
C
Hand Case Neck Turner Pilot
Pilot/Neck Reamers: $11.95
98877 .17 Cal. 98883 7mm Cal.
98876 .20 Cal. 98884 .30 Cal.
98878 .223 Cal. 98886 8mm Cal.
98879 .6mm/243 Cal. 98887 .338 Cal.
98880 .25 Cal. 98889 .35 Cal.
98881 6.5mm Cal. 98891 .375 Cal.
98882 .270 Cal.
D Hand Case Neck Turner Pilots
Hand Case Neck Turner Pilots: $11.95
90405 .17 Cal. 90413 .30 Cal. 90421 .40 Cal.
90406 .20 Cal. 90414 .31 Cal. 90422 .41 Cal.
90407 .22 Cal. 90415 .32 Cal. 90423 .416 Cal.
90408 .24 Cal. 90416 .33 Cal. 90424 .44 Cal.
90409 .25 Cal. 90417 .34 Cal. 90425 .45 Cal.
90410 .26 Cal. 90418 .35 Cal. 90426 .475 Cal.
90411 .27 Cal. 90419 .36 Cal. 90427 .500 Cal.
90412 .28 Cal./7mm 90420 .37 Cal.
rcbs.com rcbs.com
n 22 l n 23 l
D
E
Get yourself out a jam with the new RCBS ® Pow’r Pull ® E Pow’r Pull
Kit. This
kinetic style bullet puller’s rugged one-piece body and userfriendly
ergonomic handle resolves mistakes quickly and easily.
The three case holding chucks will accommodate cases from
5.7x28mm and .22 Hornet up through the WSM and RUM family
of cartridges.
Note: Not for use with rimfire cartridges.
09412 Pow’r Pull Kit $24.95
09451 Replacement Small Chuck Assembly $6.95
09418 Replacement Chuck Assembly $6.95
09416 Magnum Chuck Assembly (for WSM & Belted Mags) $6.95
® Kit
Not sure about the powder charge? Need to change bullets? The
RCBS ® F Standard Bullet Puller
Standard Bullet Puller is designed to easily pull and not
damage jacketed bullets. It utilizes the standard 7/8”-14 thread
and may be used in any single stage reloading press having this
thread.
Note: Not for use with rimfire cartridges.
09440 Standard Bullet Puller w/o Collet $24.95
Standard Bullet Puller Collets: $13.95
09419 .17 09429 .348
09438 .20 09430 .35/.38 Spec.
09420 .22 09437 9.3mm
09421 6mm 09431 .375
09422 .25 09432 .40
09423 6.5mm 09433 .41
09424 .270 09434 .416
09425 7mm 09435 .44/11mm
09426 .30/7.35mm 09436 .45
09427 .338 09439 .475
09428 .32/8mm 09445 .500
F