THE WORLD OF TIMING BELTS - MAELabs UCSD

More documents

Recommendations

Info

pm of Faster Shaft 30,000 20,000 10,000 8,000 6,000 5,000 4,000 3,000 2,000 1,000 800 600 500 400 300 200 100 3 mm HTD 5 mm HTD 0 50 100 150 200 250 300 350 (lb⋅in) 5.7 11 17 23 28 34 40 (N⋅m) Design Torque (T peak) Fig. 42 HTD Belt Selection Guide 3,450 rpm 1,750 rpm 1,160 rpm 870 rpm T-144
20,000 10,000 8,000 6,000 5,000 4,000 3,000 2,000 1,000 rpm of Faster Shaft 30,000 800 600 500 400 300 200 100 MXL (.080" & .0816") XL (.200") 0 2 4 6 8 10 12 14 (lb⋅in) 32 64 96 128 160 192 224 (oz⋅in) 0.23 0.45 0.68 0.9 1.13 1.35 1.58 (N⋅m) Design Torque (T peak) Fig. 43 Trapezoidal Belt Selection Guide 3,450 rpm 1,750 rpm 1,160 rpm 870 rpm T-145
Page 1 and 2:
SECTION 1 INTRODUCTION THE WORLD OF
Page 3 and 4:
The main stress line in a trapezoid
Page 5 and 6:
Figure 5 shows an illustrative grap
Page 7 and 8:
4.3 Noise The smoother meshing acti
Page 9 and 10:
The tension members are embedded in
Page 11 and 12:
The "S" twist is obtained if we vis
Page 13 and 14:
SECTION 7 BELT TOOTH PROFILES There
Page 15 and 16:
In order to provide fast reference,
Page 17 and 18:
No. of Pitch Diameter Outside Diame
Page 19 and 20:
No. of Pitch Diameter Outside Diame
Page 21 and 22:
T-23 7.003 7.066 7.130 7.194 7.257
Page 23 and 24:
T-25 13.130 13.250 13.369 13.488 13
Page 25 and 26:
T-27 6.015 6.053 6.090 6.128 6.166
Page 27 and 28: T-29 5 mm Pitch HTD ® Pitch Pulley
Page 29 and 30: T-31 8 mm Pitch HTD ® Pulley Dimen
Page 31 and 32: T-33 2 mm Pitch GT ® Pulley Dimens
Page 33 and 34: T-35 Table 13 (Cont.) 3 mm Pitch GT
Page 35 and 36: T-37 5 mm Pitch GT ® Pulley Dimens
Page 37 and 38: SECTION 9 DESIGN AND INSTALLATION S
Page 39 and 40: slip), and because they require min
Page 41 and 42: elts than pure water. Urethane timi
Page 43 and 44: angular shaft alignment, resulting
Page 45 and 46: • Design with large pulleys with
Page 47 and 48: inch (0.4 mm per 25 mm) of span len
Page 49 and 50: overloaded which may cause an edge
Page 51 and 52: 4. Pulleys for fixed center systems
Page 53 and 54: When identifying a shaft center loc
Page 55 and 56: procedures can be used for finding
Page 57 and 58: In measuring the length of a synchr
Page 59 and 60: Tolerancing/Inspection Procedure: A
Page 61 and 62: Table 31 ISO Pulley O.D. Tolerances
Page 63 and 64: Belt Type MXL XL 2 mm GT 3 mm GT &
Page 65 and 66: Drive selection procedures for driv
Page 67 and 68: Fig. 39 Belt Nomenclature The use o
Page 69 and 70: T-71 1.000 1.042 1.053 1.056 1.059
Page 71 and 72: T-73 2.000 2.083 2.100 2.105 2.118
Page 73 and 74: SECTION 22 CENTER DISTANCE FORMULAS
Page 75 and 76: 22.6 Determination Of Belt Size For
Page 77: pm of Faster Shaft 14,000 12,000 10
Page 81 and 82: The number of teeth in mesh on the
Page 83 and 84: Table 40 (Cont.) Rated Torque (N⋅
Page 89 and 90: Table 43 (Cont.) Rated Kilowatts fo
Page 93 and 94: Table 45 Rated Torque (N⋅m) for S
Page 95: Table 47 Rated Torque (lb⋅in) for
show all

THE WORLD OF TIMING BELTS - MAELabs UCSD

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?