Sgdhsgh fdftdh rth fh fgh fghfgh fgh fgh fgh fgh fdh dfh ... - Fixturlaser

More documents

Recommendations

Info

PRE-ALIGNMENT FUNCTIONS In an effort to obtain the best possible conditions for shaft alignment, it is necessary to perform some prealignment checks. In many cases it is necessary to make these checks in order to obtain precise alignment. It is often impossible to reach the desired alignment results if you do not make any pre-alignment checks. Before going on site, check the following: Safety regulations? What are the required tolerances? Any offsets for dynamic movements? Are there any restrictions for mounting the measuring system? Is it possible to rotate the shafts? What shim size is needed? Before setting up the alignment system on the machine, check the machine foundation, bolt and shim conditions. Also check if there are any restrictions in adjusting the machine (if e.g. there is enough space to move the machine). After the visual checks have been performed, there are some conditions that have to be considered: Make sure the machine is off line and safety tagged. Check that the machine has the right temperature for alignment? Take away old rusty shims (check that you can remove shims). Check coupling assembly and loosen the coupling bolts. Check soft foot conditions. Mechanical looseness. <strong>Fixturlaser</strong> GO Pro Manual 3 rd edition 7.2
Check coupling and shaft run-out. Pipe work strain. Coarse alignment. Check coupling gap (axial alignment). MOUNTING The sensors are mounted as described in chapter “Shaft Alignment Horizontal Machines”. STARTING THE PROGRAM Start the program by selecting the Vertical Shaft Alignment icon in the Main Menu and press OK. Go to Settings for selecting settings. <strong>Fixturlaser</strong> GO Pro Manual 3 rd edition 7.3
Page 1: Fixturlaser GO Pro user`s MANUAL
Page 4 and 5: Fixturlaser GO Pro Manual 3 rd edit
Page 6 and 7: END USER LICENSE AGREEMENT The righ
Page 8 and 9: The laser is classified in accordan
Page 10 and 11: LASER PRECAUTIONS Fixturlaser GO Pr
Page 12 and 13: Handle any batteries with care. Bat
Page 14 and 15: The chains on the V-block fixtures
Page 16 and 17: APPLICATION PROGRAMS Shaft Alignmen
Page 18 and 19: PRE-ALIGNMENT FUNCTIONS In an effor
Page 20 and 21: MOUNTING The sensor marked “M”
Page 22 and 23: The laser of the M-sensor can be ad
Page 24 and 25: TOLERANCE TABLE Alignment tolerance
Page 26 and 27: SETTINGS Settings unique for this a
Page 28 and 29: Turn off inclinometers If the incli
Page 30 and 31: SOFTCHECK TARGET VALUES Go to Softc
Page 32 and 33: Select the register icon and press
Page 34 and 35: EVALUATING THE RESULT The angle and
Page 36 and 37: ALIGNMENT If the machine has been a
Page 38 and 39: OTHER FEATURES M and S unit LED fun
Page 40 and 41: Measurement with disabled inclinome
Page 44 and 45: SETTINGS Settings unique for this a
Page 46 and 47: ENTER DIMENSIONS The screen display
Page 48 and 49: Rotate the shafts 90° to the secon
Page 50 and 51: EVALUATING THE RESULT The angle and
Page 54 and 55: STARTING THE PROGRAM Start the prog
Page 56 and 57: MEASUREMENT VALUE REGISTRATION Sele
Page 58 and 59: SHAFT ALIGNMENT Return to shaft ali
Page 60 and 61: STARTING THE PROGRAM Start the Targ
Page 62 and 63: ANGLE AND OFFSET VALUES Select the
Page 66 and 67: The Memory has the capacity to stor
Page 68 and 69: TRANSFER FILES TO A PC 1. Turn on t
Page 70 and 71: SHAFT ALIGNMENT FOR VERTICAL MACHIN
Page 72 and 73: Measurement unit Changes between mm
Page 74 and 75: 1. USB slave 1 OPERATING MODES The
Page 76 and 77: BACKLIGHT If no button is pressed w
Page 78 and 79: The upgrade file will be automatica
Page 80 and 81: OPERATION In order for the display
Page 82 and 83: WIRELESS SETTINGS The Wireless Sett
Page 84 and 85: Choose the unit to pair with the di
Page 88 and 89: Peripherals 1 USB slave port Wirele
Page 90: Measurement distance Up to 10m Dete

Sgdhsgh fdftdh rth fh fgh fghfgh fgh fgh fgh fgh fdh dfh ... - Fixturlaser

Create successful ePaper yourself

Delete template?

Save as template?