Page 1 of 18 On Board Diagnostics PCED 7/25/2009 http://www ...
Page 1 of 18 On Board Diagnostics PCED 7/25/2009 http://www ...
Page 1 of 18 On Board Diagnostics PCED 7/25/2009 http://www ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>On</strong> <strong>Board</strong> <strong>Diagnostics</strong> <strong>PCED</strong><br />
<strong>http</strong>://<strong>www</strong>.fordtechservice.dealerconnection.com/pubs/content/~WV52/~MUS~LEN/14/...<br />
<strong>Page</strong> 14 <strong>of</strong> <strong>18</strong><br />
7/<strong>25</strong>/<strong>2009</strong><br />
GO to KB61 .<br />
REPAIR the open circuit.<br />
KB61 CHECK THE FPDM2 PWR CIRCUIT FOR AN OPEN IN THE HARNESS<br />
Measure the resistance between:<br />
( + ) FPDM2 Connector, Harness Side ( - ) FPDM2 PWR Relay Connector, Harness Side<br />
FPDM2 PWR - Pin 5 FPDM2 PWR - Pin 5<br />
Is the resistance less than 5 ohms?<br />
Yes<br />
INSTALL a new FPDM2 PWR relay. GO to KB66 .<br />
No<br />
KB62 CHECK THE FPM2 CIRCUIT FOR AN OPEN IN THE HARNESS<br />
FPDM2 connector disconnected.<br />
PCM connector disconnected.<br />
Measure the resistance between:<br />
( + ) FPDM2 Connector, Harness Side ( - ) PCM Connector, Harness Side<br />
FPM2 - Pin 1<br />
FPM2<br />
Is the resistance less than 5 ohms?<br />
GO to KB63 .<br />
Yes<br />
REPAIR the open circuit.<br />
No<br />
KB63 CHECK THE FPM2 CIRCUIT FOR A SHORT TO VOLTAGE IN THE HARNESS<br />
Key ON, engine OFF.<br />
Measure the voltage between:<br />
( + ) FPDM2 Connector, Harness Side ( - )<br />
FPM2 - Pin 1<br />
Ground<br />
Is the voltage less than 1 V?<br />
Key in OFF position.<br />
GO to KB64 .<br />
Yes<br />
REPAIR the short circuit.<br />
No<br />
KB64 CHECK THE FPM2 CIRCUIT FOR A SHORT TO GROUND IN THE HARNESS<br />
Measure the resistance between:<br />
( + ) FPDM2 Connector, Harness Side ( - )<br />
FPM2 - Pin 1<br />
Ground<br />
Is the resistance greater than 10K ohms?<br />
GO to KB65 .<br />
Yes<br />
REPAIR the short circuit.<br />
No<br />
KB65 CHECK FOR FPM2 OUTPUT FROM THE FPDM2<br />
FPDM2 connector connected.<br />
Key ON, engine OFF.<br />
Note: It is OK for the voltage to cycle below this range and then return within range.<br />
Measure the voltage between:<br />
( + ) PCM Connector, Harness Side ( - )<br />
FPM2<br />
Ground<br />
Is the voltage between 0.02 - 1 V?<br />
Yes<br />
INSTALL a new PCM. REFER to Section 2, Flash Electrically Erasable<br />
Programmable Read <strong>On</strong>ly Memory (EEPROM).<br />
INSTALL a new FPDM2.<br />
No