AT Commands Reference Guide - HW Kitchen

More documents

Recommendations

Info

3.5.3 Hayes Compliant AT Commands 3.5.3.1 Generic Modem Control 3.5.3.1.1 Set To Factory-Defined Configuration - &F AT Commands Reference Guide 80000ST10025a Rev. 5 - 09/07/08 &F - Set To Factory-Defined Configuration SELINT 0 / 1 / 2 AT&F[] Execution command sets the configuration parameters to default values specified by manufacturer; it takes in consideration hardware configuration switches and other manufacturer-defined criteria. Parameter: : 0 - just the factory profile base section parameters are considered. 1 - either the factory profile base section and the extended section are considered (full factory profile). Note: if parameter is omitted, the command has the same behaviour as AT&F0 Reference V25ter. 3.5.3.1.2 Soft Reset - Z Z - Soft Reset SELINT 0 / 1 / 2 ATZ[] Execution command loads the base section of the specified user profile and the extended section of the default factory profile. Parameter: 0..1 - user profile number Note: any call in progress will be terminated. Note: if parameter is omitted, the command has the same behaviour as ATZ0. Reference V25ter. 3.5.3.1.3 Select Active Service Class - +FCLASS +FCLASS - Select Active Service Class SELINT 0 / 1 / 2 AT+FCLASS= Set command sets the wireless module in specified connection mode (data, fax, voice), hence all the calls done afterwards will be data or voice. Parameter: Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 34 of 434
AT Commands Reference Guide 80000ST10025a Rev. 5 - 09/07/08 +FCLASS - Select Active Service Class SELINT 0 / 1 / 2 0 - data 1 - fax class 1 8 - voice AT+FCLASS? Read command returns the current configuration value of the parameter . AT+FCLASS=? Test command returns all supported values of the parameters . Reference GSM 07.07 3.5.3.1.4 Default Reset Basic Profile Designation - &Y &Y - Default Reset Basic Profile Designation SELINT 0 / 1 / 2 AT&Y[] Execution command defines the basic profiles which will be loaded on startup. Parameter: 0..1 - profile (default is 0): the wireless module is able to store 2 complete configurations (see &W). Note: differently from command Z, which loads just once the desired profile, the one chosen through command &Y will be loaded on every startup. Note: if parameter is omitted, the command has the same behaviour as AT&Y0 3.5.3.1.5 Default Reset Full Profile Designation - &P &P - Default Reset Full Profile Designation SELINT 0 / 1 / 2 AT&P[] Execution command defines which full profile will be loaded on startup. Parameter: 0..1 – profile number: the wireless module is able to store 2 full configurations (see command &W). Note: differently from command Z, which loads just once the desired profile, the one chosen through command &P will be loaded on every startup. Note: if parameter is omitted, the command has the same behaviour as AT&P0 Reference Telit Specifications Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 35 of 434
Page 1 and 2: AT Commands Reference Guide GM862-Q
Page 3 and 4: Contents AT Commands Reference Guid
Page 5 and 6: DISCLAIMER AT Commands Reference Gu
Page 7 and 8: 2 APPLICABLE DOCUMENTS a) ETSI GSM
Page 9 and 10: 3.2 AT Command Syntax AT Commands R
Page 11 and 12: ATCMD1 CMD2=10+CMD1;+CMD2=, ,10;+CM
Page 13 and 14: AT Commands Reference Guide 80000ST
Page 15 and 16: 3.2.3 Information Responses And Res
Page 21 and 22: +FCLASS +ILRR +DR +CSCS +CR +CRLP +
Page 23 and 24: 3.4 AT Commands Availability Table
Page 25 and 26: COMMAND GM862 - QUAD GM862- QUAD- P
Page 31 and 32: 3.5 AT Commands References 3.5.1 Co
Page 33: 3.5.2.1.1 Select Interface Style -
Page 55 and 56: 3.5.3.3.3 Pulse Dial - P AT Command
Page 63 and 64: 3.5.3.7.6 Command Line Editing Char
Page 73 and 74: +CBST - Select Bearer Service Type
Page 85 and 86:
AT Commands Reference Guide 80000ST
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
3.5.4.3.9 Calling Line Identificati
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
3.5.4.3.12 Call Holding Services -
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
+CPIN - Enter PIN AT Commands Refer
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
3.5.5 ETSI GSM 07.05 AT Commands fo
Page 171 and 172:
Page 173 and 174:
+CPMS - Preferred Message Storage [
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
+CNMI - New Message Indications To
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
+CMGR - Read Message AT Commands Re
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
3.5.5.4 Message Sending And Writing
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
3.5.6 FAX Class 1 AT Commands 3.5.6
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
#CEER - Extended numeric error repo
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
3.5.7.1.20 Software Shut Down - #SH
Page 253 and 254:
Page 255 and 256:
AT#TEMPMON? #TEMPMEAS: , where: an
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
3.5.7.1.28 STAT_LED GPIO Setting -
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
: handset analogue output gain 0..6
Page 297 and 298:
Page 299 and 300:
3.5.7.1.70 Handset Noise Reduction
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
context AT Commands Reference Guide
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
3.5.7.3.5 Socket Configuration - #S
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
#DNS - Manual DNS Selection AT Comm
Page 345 and 346:
3.5.7.5.12 Socket Parameters Save -
Page 347 and 348:
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
Page 371 and 372:
Page 373 and 374:
Page 375 and 376:
3.5.7.6.10 SMTP Read Message - #EMA
Page 377 and 378:
Page 379 and 380:
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
Page 413 and 414:
Page 415 and 416:
Page 417 and 418:
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
Page 429 and 430:
Page 431 and 432:
4 List of acronyms AT Commands Refe
Page 433 and 434:
5 Document Change Log AT Commands R
show all

AT Commands Reference Guide - HW Kitchen

Create successful ePaper yourself

Delete template?

Save as template?