MDH-302/402 & Icepic / Selectable Ice Series - Manitowoc ...

More documents

Recommendations

Info

Maintenance Section 4 MONTHLY ICE CRUSHER ASSEMBLY CLEANING Once the ice crusher hub assembly has been removed the crusher is ready to be cleaned and sanitized. Follow the steps below for proper cleaning and sanitizing procedures. 1. Assure the unit is unplugged. 2. Mix a solution of mild detergent to clean the ice crusher components. 3. Using the mild detergent solution and a soft bristle brush or clean cloth, clean the following ice crusher components. • Blade / Hub assembly • Cosmetic Chute • Drip Pan • Crusher Housing • Ice Crusher Motor Shaft • Rocking Chute Door HOUSING DOOR BLADE/HUB ASSEMBLY HOUSING ROCKING CHUTE DOOR BLADE/HUB ASSEMBLY ICE DOOR BLADE/HUB ASSEMBLY DRIP PAN COSMETIC CHUTE HOUSING HOUSING GENI ICEPIC DRIP PAN COSMETIC CHUTE GENII ICEPIC CRUSHED ICE DOOR COSMETIC CHUTE SANITARY LEVER SELECTABLE ICE MOTOR SHAFT DRIP PAN MOTOR SHAFT MOTOR SHAFT 4-6 Part Number 020003999 4/12
Section 4 Maintenance 4. Rinse all of the parts with clean water. 5. Prepare 2 gallons of sanitizing solution by mixing a ½ ounce of household bleach (that contains 5.25% sodium hypochlorite) with 2 gallons of 120 F water. The mixture should not exceed 100 PPM of chlorine. Or mix a solution of any approved sanitizer, following the directions for mixing and applying the sanitizer. 6. Apply sanitizer to all parts with clean cloth, or by spraying. 7. Allow to air dry. DO NOT RINSE. 8. Reassemble the Ice Crusher Assembly by following the instructions in the “Reassembling the Ice Crusher Assembly” section. 9. Insert the blade assembly into crusher housing. When inserting blade assembly you must align the stationary blades with the locating slots in the crusher housing. 10. When inserting the blade assembly into the crusher housing you must also make sure the axle knob is in a vertical position. This will align the rotating blades with the housing to assure a quick and easy installation. 11. Once all blades are in the housing you will need to align the crusher axle with the motor shaft. You can do this by turning the axle knob and pushing the blade assembly toward the motor until the crusher hub is flush with the end of the housing. 12. To lock the blade assembly into the housing rotate the crusher hub counter clockwise until the locking tab snaps into place and the crusher hub is secure. 13. Replace the crusher drip pan, slide until it snaps into place. 14. Reattach the decorative ice chute by inserting the chute rod through the chute, Housing Mount, and Motor Mount. Secure the Chute Rod by inserting cotter pin through the rod on the right side of the housing mount. Make sure arm of microswitch is in front of vertical protrusions on top of decorative chute. 15. Reinstall the Rocking Chute Door. 16. Reinstall the merchandiser, and secure with the two (2) screws that were removed during disassembly. 17. 110V power may be reapplied when unit is completely reassembled. REASSEMBLE THE ICE CRUSHER ASSEMBLY 1. Insert the blade assembly into crusher housing. When inserting blade assembly you must align the stationary blades with the locating slots in the crusher housing. GENI, GENII & SCI blade assemblies are the same, GENII is illustrated on the left. 2. When inserting the blade assembly into the crusher housing you must also make sure the axle knob is in a vertical position. This will align the rotating blades with the housing to assure a quick and easy installation. 3. Once all blades are in the housing you will need to align the crusher axle with the motor shaft. You can do this by turning the axle knob and pushing the blade assembly toward the motor until the crusher hub is flush with the end of the housing. 4. To lock the blade assembly into the housing rotate the crusher hub counter clockwise until the locking tab snaps into place and the crusher hub is secure. 5. Replace the crusher drip pan, slide until it snaps into place by pulling up slightly on the crusher assembly and pushing the drip pan toward the foam front. GENI, GENII & SCI drip pans are the same, GENII is illustrated on the left. Part Number 020003999 4/12 4-7
Page 1 and 2: MDH-302/402 & Icepic / Selectable I
Page 3 and 4: Section 1 General Information Secti
Page 5 and 6: Section 4 Maintenance Section 5 Bef
Page 7 and 8: Section 1 General Information Read
Page 9 and 10: General These instructions are prov
Page 11 and 12: Section 2 Installation Instructions
Page 25 and 26: Section 3 Operation General System
Page 27 and 28: Section 3 Operation MDH-302 Cold Ca
Page 29 and 30: Section 3 Operation Component Ident
Page 31 and 32: Section 3 Operation Syrup Delivery
Page 33 and 34: Section 3 Operation Operation Check
Page 35 and 36: Section 4 Maintenance Cleaning DAIL
Page 37 and 38: Section 4 Maintenance Preventive Ma
Page 39: Section 4 Maintenance 2. Remove the
Page 43 and 44: Section 4 Maintenance Front Service
Page 45 and 46: Section 4 Maintenance 5. Draw rinse
Page 47 and 48: Section 5 Before Calling for Servic
Page 54: © 2012 Manitowoc Continuing produc

MDH-302/402 & Icepic / Selectable Ice Series - Manitowoc ...

Create successful ePaper yourself

Delete template?

Save as template?